ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing and Configuring SPO Workstation Software Continue by installing network services (11.2). 11.3. Installing Network Services on the Windows NT Workstation To install network services for the SPO workstation: 1. Click Start, Settings, Control Panel to go to the control panel. 2. In the control panel, double-click Network. 3. Click the Services tab. 4. Click Add. 5. Click Microsoft Peer Web Services. 6. Click OK. You are prompted to insert the Windows NT CD-ROM. 7. Insert the CD-ROM. If a Windows CD-ROM window appears, you can close it. Verify that the path is set to D:\I386. 8. Click OK. A Peer Web Services Setup window appears. 9. Click OK. 10. Click OK again. A message asks if you want to create a directory. 11. Click Yes. A Publishing Directories window appears. 12. Click OK. 13. Click Yes to create the directories. In a few seconds, a window appears for installing the SQL Server driver. 14. Click SQL Server once to highlight it, then click OK. Setup completes. 15. Click OK. 16. Click Add to add more services. 17. By the same method as that for the Peer Web Service, select and add Simple TCP/IP services. 18. Review the list of services, which should contain the following: • Computer browser • Microsoft Peer Web Services • NetBIOS interface 11–14 Version 009B (Web Only) 7850 5104–009
• RPC configuration • Server • Simple TCP/IP services Installing and Configuring SPO Workstation Software • Workstation 19. Close the Network window. A message asks whether you want to shut down the computer at this time. 20. Click No. Continue with 11.3. 11.4. Installing the Latest Service Pack for Windows NT Workstation 4.0 Note: The latest recommended service pack is shipped with the system. The instructions that follow are based on Windows NT Service Pack 4. If a later service pack arrived with the system, install it using these instructions as a guideline. To install a Windows NT Service Pack on the SPO workstation, follow these steps: 1. Insert the Windows NT Service Pack n CD-ROM into the drive unit. Internet Explorer should start automatically and a Service Pack n home page appears. 2. Click the Install Service Pack n link, then click Open. A License Agreement screen appears. 3. Click Accept the License Agreement. 4. Click Install. A Service Pack Setup screen appears. Files are copied and the service pack is installed. During installation, a Windows NT Service Pack Setup window may appear, listing the name of a file with the following message: This file has been identified as an oem-installed file. Would you like to overwrite the version of the file on your system with the Service Pack n version? 5. Click No for all file messages that may appear. When setup finishes, a prompt appears to reboot the system. 6. Remove the CD-ROM from the drive and click Restart. Continue with 11.4. 7850 5104–009 Version 009B (Web Only) 11–15
- Page 229 and 230: 8.9. Retrieving and Applying Fixes
- Page 231 and 232: Installing UnixWare 7 Console outpu
- Page 233 and 234: Installing UnixWare 7 • Use the u
- Page 235 and 236: Section 9 Installing the ClearPath
- Page 237 and 238: Section 10 Installing SPO Basic Edi
- Page 239 and 240: Installing SPO Basic Edition and Re
- Page 241 and 242: Installing SPO Basic Edition and Re
- Page 243 and 244: Installing SPO Basic Edition and Re
- Page 245 and 246: Installing SPO Basic Edition and Re
- Page 247 and 248: Installing SPO Basic Edition and Re
- Page 249 and 250: Installing SPO Basic Edition and Re
- Page 251 and 252: Installing SPO Basic Edition and Re
- Page 253 and 254: Installing SPO Basic Edition and Re
- Page 255 and 256: Installing SPO Basic Edition and Re
- Page 257 and 258: Installing SPO Basic Edition and Re
- Page 259 and 260: Installing SPO Basic Edition and Re
- Page 261 and 262: Installing SPO Basic Edition and Re
- Page 263 and 264: Installing SPO Basic Edition and Re
- Page 265 and 266: 2. At the password prompt, enter un
- Page 267 and 268: Section 11 Installing and Configuri
- Page 269 and 270: SPO Server SPO Basic Edition SPO Wo
- Page 271 and 272: Installing and Configuring SPO Work
- Page 273 and 274: Installing and Configuring SPO Work
- Page 275 and 276: Installing and Configuring SPO Work
- Page 277 and 278: Installing and Configuring SPO Work
- Page 279: Installing and Configuring SPO Work
- Page 283 and 284: Installing and Configuring SPO Work
- Page 285 and 286: Installing and Configuring SPO Work
- Page 287 and 288: • Installing the SPO Basic Editio
- Page 289 and 290: Installing and Configuring SPO Work
- Page 291 and 292: Installing and Configuring SPO Work
- Page 293 and 294: Installing and Configuring SPO Work
- Page 295 and 296: Installing and Configuring SPO Work
- Page 297 and 298: Installing and Configuring SPO Work
- Page 299 and 300: Installing and Configuring SPO Work
- Page 301 and 302: Installing and Configuring SPO Work
- Page 303 and 304: Installing and Configuring SPO Work
- Page 305 and 306: Installing and Configuring SPO Work
- Page 307 and 308: Section 12 Configuring Intel Nodes
- Page 309 and 310: Configuring Intel Nodes for Monitor
- Page 311 and 312: Configuring Intel Nodes for Monitor
- Page 313 and 314: Configuring Intel Nodes for Monitor
- Page 315 and 316: Configuring Intel Nodes for Monitor
- Page 317 and 318: Configuring Intel Nodes for Monitor
- Page 319 and 320: Configuring Intel Nodes for Monitor
- Page 321 and 322: Section 13 Installing the Basic OS
- Page 323 and 324: Installing the Basic OS 2200 IOE Yo
- Page 325 and 326: Installing the Basic OS 2200 IOE 5.
- Page 327 and 328: Installing the Basic OS 2200 IOE 2.
- Page 329 and 330: Installing the Basic OS 2200 IOE Yo
• RPC configuration<br />
• Server<br />
• Simple TCP/IP services<br />
Installing <strong>and</strong> Configuring SPO Workstation Software<br />
• Workstation<br />
19. Close the Network window.<br />
A message asks whether you want to shut down the computer at this time.<br />
20. Click No.<br />
Continue with 11.3.<br />
11.4. Installing the Latest Service Pack for Windows<br />
NT Workstation 4.0<br />
Note: The latest recommended service pack is shipped with the system. The<br />
instructions that follow are based on Windows NT Service Pack 4. If a later<br />
service pack arrived with the system, install it using these instructions as a<br />
guideline.<br />
To install a Windows NT Service Pack on the SPO workstation, follow these steps:<br />
1. Insert the Windows NT Service Pack n CD-ROM into the drive unit. Internet Explorer<br />
should start automatically <strong>and</strong> a Service Pack n home page appears.<br />
2. Click the Install Service Pack n link, then click Open.<br />
A License Agreement screen appears.<br />
3. Click Accept the License Agreement.<br />
4. Click Install.<br />
A Service Pack Setup screen appears.<br />
Files are copied <strong>and</strong> the service pack is installed. During installation, a Windows NT<br />
Service Pack Setup window may appear, listing the name of a file with the following<br />
message:<br />
This file has been identified as an oem-installed file.<br />
Would you like to overwrite the version of the file on your system with<br />
the Service Pack n version?<br />
5. Click No for all file messages that may appear.<br />
When setup finishes, a prompt appears to reboot the system.<br />
6. Remove the CD-ROM from the drive <strong>and</strong> click Restart.<br />
Continue with 11.4.<br />
7850 5104–009 Version 009B (Web Only) 11–15
Change language