ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing Windows NT Server 4.0 (DR/2) 6.1. Determining Whether Software Is Preloaded Caution To prevent installation problems, or wasted time, determine whether Windows NT has been preloaded. Then follow either the procedure for preloaded software or the full installation procedure, as appropriate. To determine whether the Windows NT operating system is preloaded, 1. Power on the Intel node and allow it to fully boot (takes about 2 minutes). 2. If the Windows NT Software License Agreement screen appears, the operating system is preloaded. If Windows NT is preloaded, perform the steps described in 6.2. Then complete the installation as described in Section 7. If Windows NT is not preloaded, 1. Configure the RAID controller (6.3). 2. Install the Windows NT operating system (6.4). 3. Log on to Windows NT (6.5). 4. Complete the installation (Section 7). 6.2. Steps to Take If Windows NT Is Preloaded You must take the steps below to initially configure Windows NT when it is preloaded. Notes: • Before powering on the Intel node, verify that the preloaded RAID disks are installed into the correct bays as labeled on the disks. See the DR/2 system map for the location and layout of the drive bays. • If you decide to perform a full installation even though the system is preloaded, do not format the RAID disk. Instead, use the DAC BIOS utility to initialize the RAID volume before you reload the operating system. Formatting the disk makes the drive unrecognizable to the software. 1. Power the Intel node on and allow it to fully boot (takes about 2 minutes). Watch the messages on the screen for the ALT-R prompt. 2. Press Alt-R to start the Mylex RAID EzAssist utility. An EzAssist Menu for configuring RAID logical arrays appears as follows: ----EzAssist Menu---- Configure RAID Drive 6–4 Version 009B (Web Only) 7850 5104–009
Installing Windows NT Server 4.0 (DR/2) View or Modify Controller Configuration Perform Administration on... Rescan for New Devices Advanced Options 3. Use the arrow keys to select the Configure RAID Drive option, then press Enter. A Configuration Method menu appears: ------Configuration Method----- Automatic Assisted Custom Note: Unless noted otherwise, use the arrow keys to select menu options throughout the rest of this procedure. 4. If there are no disks to configure, return to the EzAssist menu (step 7) and select Advanced Options; then select “clear configuration.” You will then be able to configure the RAID drive. 5. Select Automatic, then press Enter. The RAID Configuration Summary window appears: RAID Configuration Summary Logical Drive 0 Fault Tolerance: Yes Spare: No Optimization: Performance Logical Drive Count: 1 Total Capacity: 17.0 GB Chan: 10 Vendor Model Version Capacity (GB) Status 1:00 UNISYS ....... 17.0 Online 1:01 UNISYS ....... 17.0 Online A message window appears: Writing RAID Configuration Please wait... A final window appears: Congratulations! Configuration Status Logical Drive 0 RAID configuration is successful. You may utilize this drive immediately. [Reboot] Main Menu 6. Press Ctrl-Alt-Del to reboot. A Software License Agreement screen appears. 7. Have the client, or a representative of the client, accept the license agreement as follows: 7850 5104–009 Version 009B (Web Only) 6–5
- Page 101 and 102: Installing Windows NT Server, Enter
- Page 103 and 104: Installing Windows NT Server, Enter
- Page 105 and 106: Installing Windows NT Server, Enter
- Page 107 and 108: Installing Windows NT Server, Enter
- Page 109 and 110: Installing Windows NT Server, Enter
- Page 111 and 112: Installing Windows NT Server, Enter
- Page 113 and 114: Installing Windows NT Server, Enter
- Page 115 and 116: Installing Windows NT Server, Enter
- Page 117 and 118: Installing Windows NT Server, Enter
- Page 119 and 120: Installing Windows NT Server, Enter
- Page 121 and 122: Installing Windows NT Server, Enter
- Page 123 and 124: Section 5 Installing Windows NT Ser
- Page 125 and 126: Installing Windows NT Server, Enter
- Page 127 and 128: Installing Windows NT Server, Enter
- Page 129 and 130: Installing Windows NT Server, Enter
- Page 131 and 132: Installing Windows NT Server, Enter
- Page 133 and 134: ID 0 1 2 3 4 5 6 Installing Windows
- Page 135 and 136: Installing Windows NT Server, Enter
- Page 137 and 138: Installing Windows NT Server, Enter
- Page 139 and 140: Installing Windows NT Server, Enter
- Page 141 and 142: Installing Windows NT Server, Enter
- Page 143 and 144: Installing Windows NT Server, Enter
- Page 145 and 146: Installing Windows NT Server, Enter
- Page 147 and 148: Installing Windows NT Server, Enter
- Page 149 and 150: Section 6 Installing Windows NT Ser
- Page 151: Installing Windows NT Server 4.0 (D
- Page 155 and 156: Installing Windows NT Server 4.0 (D
- Page 157 and 158: Installing Windows NT Server 4.0 (D
- Page 159 and 160: Installing Windows NT Server 4.0 (D
- Page 161 and 162: Installing Windows NT Server 4.0 (D
- Page 163 and 164: Installing Windows NT Server 4.0 (D
- Page 165 and 166: • Communications Installing Windo
- Page 167 and 168: Installing Windows NT Server 4.0 (D
- Page 169 and 170: Installing Windows NT Server 4.0 (D
- Page 171 and 172: 6.5. Logging On As the Administrato
- Page 173 and 174: Section 7 Completing Windows Instal
- Page 175 and 176: 7.1. Completing Windows NT Installa
- Page 177 and 178: Completing Windows Installation 14.
- Page 179 and 180: Completing Windows Installation To
- Page 181 and 182: Completing Windows Installation 6.
- Page 183 and 184: Completing Windows Installation 3.
- Page 185 and 186: Completing Windows Installation Thi
- Page 187 and 188: SCSI 0, Bus 1, Id 5, Lun 0 ARCHIVE
- Page 189 and 190: Completing Windows Installation 8.
- Page 191 and 192: 7.1.16. Installing ess Software Com
- Page 193 and 194: Completing Windows Installation An
- Page 195 and 196: Completing Windows Installation Whe
- Page 197 and 198: Completing Windows Installation 5.
- Page 199 and 200: Completing Windows Installation A s
- Page 201 and 202: Section 8 Installing UnixWare 7 Thi
Installing Windows NT Server 4.0 (DR/2)<br />
6.1. Determining Whether Software Is Preloaded<br />
Caution<br />
To prevent installation problems, or wasted time, determine whether Windows NT<br />
has been preloaded. Then follow either the procedure for preloaded software or<br />
the full installation procedure, as appropriate.<br />
To determine whether the Windows NT operating system is preloaded,<br />
1. Power on the Intel node <strong>and</strong> allow it to fully boot (takes about 2 minutes).<br />
2. If the Windows NT Software License Agreement screen appears, the operating system<br />
is preloaded.<br />
If Windows NT is preloaded, perform the steps described in 6.2. Then complete the<br />
installation as described in Section 7.<br />
If Windows NT is not preloaded,<br />
1. Configure the RAID controller (6.3).<br />
2. Install the Windows NT operating system (6.4).<br />
3. Log on to Windows NT (6.5).<br />
4. Complete the installation (Section 7).<br />
6.2. Steps to Take If Windows NT Is Preloaded<br />
You must take the steps below to initially configure Windows NT when it is preloaded.<br />
Notes:<br />
• Before powering on the Intel node, verify that the preloaded RAID disks are installed<br />
into the correct bays as labeled on the disks. See the DR/2 system map for the<br />
location <strong>and</strong> layout of the drive bays.<br />
• If you decide to perform a full installation even though the system is preloaded, do<br />
not format the RAID disk. Instead, use the DAC BIOS utility to initialize the RAID<br />
volume before you reload the operating system. Formatting the disk makes the drive<br />
unrecognizable to the software.<br />
1. Power the Intel node on <strong>and</strong> allow it to fully boot (takes about 2 minutes).<br />
Watch the messages on the screen for the ALT-R prompt.<br />
2. Press Alt-R to start the Mylex RAID EzAssist utility.<br />
An EzAssist Menu for configuring RAID logical arrays appears as follows:<br />
----EzAssist Menu----<br />
Configure RAID Drive<br />
6–4 Version 009B (Web Only) 7850 5104–009