TESA RUGOSURF 10G Surface roughness gage TESA - Swiss ...
TESA RUGOSURF 10G Surface roughness gage TESA - Swiss ...
TESA RUGOSURF 10G Surface roughness gage TESA - Swiss ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
✓<br />
Transport<br />
packing<br />
<strong>Surface</strong> Roughness Testing<br />
Probes<br />
General Purpose Probes<br />
A 90˚ conical diamond stylus, .0004" (10μm)<br />
radius per ANSI–B46.1, ISO, and MIL specs.<br />
599-4000-1019 26834<br />
A 90˚ conical diamond stylus, .0002"<br />
(5μm) radius per DIN 4768 and certain<br />
ISO specs. This probe is identified by<br />
yellow dot at end of connector.<br />
599-4000-1026 26838<br />
Transverse Chisel Probe (Optional extra)<br />
A 90˚ sapphire chisel, .0004" (10μm)<br />
radius. Gages sharp edges or small<br />
O.D.s where probe is aligned with<br />
(in 180˚or closed position) axis of traverse.<br />
599-4000-1020-1 26835<br />
Small Bore Probe (Optional extra)<br />
A 90˚ conical diamond stylus, .0004"<br />
(10μm) radius. Gages small bores<br />
(1/8" [3.2 mm] min I.D.) up to a depth<br />
of 3/4" (19 mm).<br />
Note: Small Bore Probes can only be<br />
used in the “180˚ position” with the<br />
Pocket Surf unit supported in a height<br />
stand or other fixture.<br />
599-4000-1021 26837<br />
Parallel Chisel Probe (Optional extra)<br />
A 90˚ sapphire chisel, .0004" (10μm)<br />
radius. Gages sharp edges or small<br />
O.D.s where probe is perpendicular<br />
(in 90˚ or 270˚ position) to axis of traverse.<br />
Also for O.D.s smaller than .25" (6.35 mm)<br />
staged on 599-4000-2421 Vee Fixture.<br />
599-4000-1020-2 26836<br />
Groove Bottom Probe (Optional extra)<br />
A 90˚ conical diamond stylus, .0004"<br />
(10μm) radius. Gages grooves,<br />
recesses and holes to depths of .25"<br />
(6.35 mm). Also used for short lands<br />
and shoulders.<br />
Note: Groove Bottom Probes can only<br />
be used in the “180˚ position” with the<br />
Pocket Surf unit supported in a height<br />
stand or other fixture.<br />
599-4000-1028 26840<br />
Small Bore Probe (Optional extra)<br />
A 90˚ conical diamond stylus, .0002"<br />
(5μm) radius. Gages small bores<br />
(1/8" [3.2 mm] min I.D.) up to a depth<br />
of 3/4" (19 mm).<br />
Note: Small Bore Probes can only be<br />
used in the “180˚ position” with the<br />
Pocket Surf unit supported in a height<br />
stand or other fixture.<br />
599-4000-1027 26839<br />
J-13