solidworks
Detailing and DrawingsDimensioning Datum TargetsIn part and assembly models, you can use dimensions to control the position and shapeof datum targets.Positioning Datum Targets Without Using SketchesYou can use the Smart Dimension tool, without a sketch, to place driving and drivendimensions on datum targets. You can use driving dimensions to control the position ofthe attachment point of the datum target’s leader.Datum Target Shape DimensionsYou can add dimensions directly to the datum target shape. You can drag to modify theposition of these dimensions.In the Datum Target PropertyManager, select Show dimensions.Flag NotesFlag Note BankThe Flag Note Bank appears only on drawings that have flag notes.Sorting Flag NotesTo sort a stack of flag notes, right-click and select Sort Stack. For a stack of balloonsthat includes flag notes, the software sorts flag notes separately after it sorts the otherballoons.Foreshortened DimensionsArrow StylesTwo new arrow styles are available for foreshortened dimensions.Click Tools > Options > Document Properties > Drafting Standard > Dimensions> Linear. Under Foreshortened, the new options are:StraightSingle arrow88
Detailing and DrawingsDrafting StandardsForeshortened dimensions are available for all drafting standards. Previously, they wereonly available for the ANSI drafting standard.Link Child Views to Parent by DefaultWhen you create a projected view, the drawing view property Use named configurationis set to <Link to parent> by default. Previously, the property was set to Default.This behavior applies only to projected views created in SOLIDWORKS 2020 or later.Location for Saving a New DrawingWhen you save a new drawing, the default folder location in the Save or Save As dialogbox is the folder where the model in the drawing's first view is saved.You can override this behavior by specifying a default folder in Tools > Options > FileLocations > Show folders for > Default Save Folder.Performance Improvements in DrawingsWhen you create a drawing from an open assembly, the creation of the first view maybe faster than in previous releases.Render Pipeline in DrawingsDrawings and drawing annotations benefit from the graphics architecture introduced inSOLIDWORKS 2019, which implemented graphics acceleration and image quality scalingacross graphics cards.This architecture provides a more responsive, real-time display especially for large models.It takes advantage of modern OpenGL (4.5) and hardware-accelerated rendering tomaintain a high level of detail and frame rate when you pan, zoom, or rotate large models.These performance improvements scale up with the higher-end graphics cards not fullysupported in previous versions of the SOLIDWORKS software.Symbols on Sheet FormatsYou can include geometric tolerance and surface finish annotations on sheet formats. Theannotations cannot include leaders.89
- Page 37 and 38: SOLIDWORKS Fundamentals7. In the Sa
- Page 39 and 40: InstallationInstalling Toolbox Soft
- Page 41 and 42: 5AdministrationThis chapter include
- Page 43 and 44: AdministrationSpecifying Support In
- Page 45 and 46: AssembliesCreating Envelopes for a
- Page 47 and 48: AssembliesAdd a Group / Edit GroupA
- Page 49 and 50: AssembliesReusing a Multibody Part
- Page 51 and 52: AssembliesTo change a component fro
- Page 53 and 54: Assemblies10. In the graphics area,
- Page 55 and 56: AssembliesLinear andCircularPattern
- Page 57 and 58: AssembliesLimit Angle MateAvailable
- Page 59 and 60: Assemblies5. In the callout, modify
- Page 61 and 62: AssembliesChanges to the Step 2: Se
- Page 63 and 64: Assemblies6. Under Orient Component
- Page 65 and 66: Assemblies6. Under Mirror Type, sel
- Page 67 and 68: Assemblies4. Click OK .The pattern
- Page 69 and 70: SOLIDWORKS CAMTab CuttingYou can cr
- Page 71 and 72: SOLIDWORKS ComposerImporting Appear
- Page 73 and 74: SOLIDWORKS ComposerSee Composer Hel
- Page 75 and 76: Detailing and DrawingsTo add hole c
- Page 77 and 78: Detailing and DrawingsEditing Alter
- Page 79 and 80: Detailing and Drawings3. Click feat
- Page 81 and 82: Detailing and Drawings2. Select the
- Page 83 and 84: Detailing and DrawingsCreating Mark
- Page 85 and 86: Detailing and DrawingsSetting Custo
- Page 87: Detailing and DrawingsIn addition,
- Page 91 and 92: eDrawings• 2D annotations, genera
- Page 93 and 94: eDrawingsButtonFunctionalityResets
- Page 95 and 96: eDrawings2020Model DisplayYou can d
- Page 97 and 98: SOLIDWORKS ElectricalText LeaderYou
- Page 99 and 100: SOLIDWORKS ElectricalHorizontal lan
- Page 101 and 102: SOLIDWORKS ElectricalViewProjects m
- Page 103 and 104: SOLIDWORKS ElectricalRow StyleAutom
- Page 105 and 106: 12SOLIDWORKS Flow SimulationThis ch
- Page 107 and 108: 13SOLIDWORKS 3D InterconnectThis ch
- Page 109 and 110: 14SOLIDWORKS ManageThis chapter inc
- Page 111 and 112: SOLIDWORKS ManageCopy Manual Quanti
- Page 113 and 114: SOLIDWORKS ManageExport Feature of
- Page 115 and 116: SOLIDWORKS Manage2. Click at the up
- Page 117 and 118: SOLIDWORKS ManageThe functionality
- Page 119 and 120: SOLIDWORKS MBDSorting by Annotation
- Page 121 and 122: 16Model DisplayThis chapter include
- Page 123 and 124: Model DisplayBody Compare PropertyM
- Page 125 and 126: 17Parts and FeaturesThis chapter in
- Page 127 and 128: Parts and FeaturesDecimating a Grap
- Page 129 and 130: Parts and Features6. In the Propert
- Page 131 and 132: Parts and Features5. Drag the point
- Page 133 and 134: Parts and Features4. In the Tangent
- Page 135 and 136: Parts and FeaturesAfter creating th
- Page 137 and 138: Parts and Features9. Under Items to
Detailing and Drawings
Dimensioning Datum Targets
In part and assembly models, you can use dimensions to control the position and shape
of datum targets.
Positioning Datum Targets Without Using Sketches
You can use the Smart Dimension tool, without a sketch, to place driving and driven
dimensions on datum targets. You can use driving dimensions to control the position of
the attachment point of the datum target’s leader.
Datum Target Shape Dimensions
You can add dimensions directly to the datum target shape. You can drag to modify the
position of these dimensions.
In the Datum Target PropertyManager, select Show dimensions.
Flag Notes
Flag Note Bank
The Flag Note Bank appears only on drawings that have flag notes.
Sorting Flag Notes
To sort a stack of flag notes, right-click and select Sort Stack. For a stack of balloons
that includes flag notes, the software sorts flag notes separately after it sorts the other
balloons.
Foreshortened Dimensions
Arrow Styles
Two new arrow styles are available for foreshortened dimensions.
Click Tools > Options > Document Properties > Drafting Standard > Dimensions
> Linear. Under Foreshortened, the new options are:
Straight
Single arrow
88