Speedfax 2017
Sentron Busway Systems Tees Selection Tees are used to simplify directional and plane orientation changes in a busway system. Tees can make 90° bends left or right, and up and down along the busway run. All tees are supplied with two joint stack assemblies. 15 BUSWAY SYSTEMS Flatwise Tees, Dimensions (standard/min.) Dimensions Inches (mm) Ampere Rating “A”, ”B”, ”C” AL L-Rated 225 — 12 (305) 400 — 12 (305) 600 — 12 (305) 800 400 12 (305) 1000 600 12 (305) 1200 800 12 (305) 1350 1000 12 (305) 1600 1200 18 (457) 2000 1350,1600 18 (457) 2500 2000 18 (457) 3000 2500 18 (457) 3200 2000 18 (457) 4000 3000,3200 24 (610) CU M-Rated 225 — 12 (305) 400 — 12 (305) 600 — 12 (305) 800 400 12 (305) 1000 — 12 (305) 1200 600 12 (305) 1350 800 12 (305) 1600 1000 12 (305) 2000 1200,1350 12 (305) — 1600 18 (457) 2500 2000 18 (457) 3000 — 18 (457) 3200 — 18 (457) 4000 2500,3000,3200 18 (457) 5000 4000 24 (610) Flatwise Tees Flatwise tees are used to create left and right branches. Flat Right Suffix TEFR Flat Left Suffix TEFL Edgewise Tees, Dimensions (standard/min.) Dimensions Inches (mm) Ampere Rating “D” AL L-Rated 225 — 13 (330) 400 — 13 (330) 600 — 13 (330) 800 400 13 (330) 1000 600 13 (330) 1200 800 18 (457) 1350 1000 18 (457) 1600 1200 18 (457) 2000 1350,1600 18 (457) 2500 2000 27 (686) 3000 2500 27 (686) 3200 2000 27 (686) 4000 3000,3200 29 (737) CU M-Rated 225 — 13 (330) 400 — 13 (330) 600 — 13 (330) 800 400 13 (330) 1000 — 13 (330) 1200 600 13 (330) 1350 800 13 (330) 1600 1000 18 (457) 2000 1200,1350 18 (457) — 1600 18 (457) 2500 2000 18 (457) 3000 — 27 (686) 3200 — 27 (686) 4000 2500,3000,3200 27 (686) 5000 4000 29 (737) Edgewise Tees Edgewise tees are used to create branches that stem up or down from the busway run. Edge Up Suffix TEEU Edge Down Suffix TEED a a 12.0" (305mm) For Isolated Ground. 15-16 Siemens Industry, Inc. SPEEDFAX Product Catalog
Sentron Busway Systems End Tap Boxes Revised on 04/30/18 Selection End tap boxes are non-fusible devices used to connect cable and conduit to the end of a busway run or where busway runs connect without the need for over-current protection. End tap boxes may be installed at the end or beginning of a run. Vertical end tap boxes and horizontal end tap boxes can be installed in both horizontal and vertical applications. Extended end tap boxes are available if the application requires additional wire bending space. One joint stack assembly is shipped with each end tap box. Standard and Extended Horizontal End Tap Boxes, Dimensions Cable Lugs Dimensions Inches (mm) Wire Bend Space Per Phase & Neutral Ground Ampere Rating “A” “B” Std. “B” Ext. “C” Std. “C” Ext. Qty. Size Lugs a AL L-Rated 225 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 1 a 1 400 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 1 b 1 600 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 2 b 1 800 400 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 3 b 1 1000 600 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 4 b 1 1200 800 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 4 b 1 1350 1000 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 4 b 1 1600 1200 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 5 b 1 2000 1350,1600 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 6 b 2 2500 2000 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 8 b 2 3000 2500 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 9 b 2 3200 2000 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 9 b 2 4000 3000,3200 29 (737) 33 (838) 37 (940) 20 (508) 24 (610) 12 b 3 CU M-Rated 225 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 1 a 1 400 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 1 b 1 600 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 2 b 1 800 400 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 3 b 1 1000 — 13 (330) 30 (762) 34 (863) 17 (432) 21 (533) 4 b 1 1200 600 13 (330) 33 (838) 37 (940) 20 (508) 24 (610) 4 b 1 1350 800 13 (330) 33 (838) 37 (940) 20 (508) 24 (610) 4 b 1 1600 1000 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 5 b 1 2000 1200,1350 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 6 b 2 — 1600 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 5 b 1 2500 2000 18 (457) 33 (838) 37 (940) 20 (508) 24 (610) 8 b 2 3000 — 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 9 b 2 3200 — 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 9 b 2 4000 2500,3000,3200 27 (686) 33 (838) 37 (940) 20 (508) 24 (610) 12 b 3 5000 4000 29 (737) 33 (838) 37 (940) 20 (508) 24 (610) 15 b 4 Horizontal End Tap Box Suffix ETHS (Standard) Suffix ETHX (Extended) 15 BUSWAY SYSTEMS Standard and Extended Vertical End Tap Boxes, Dimensions Cable Lugs Dimensions Inches (mm) Wire Bend Space Per Phase & Neutral Ground Ampere Rating “A” “B” Std. “B” Ext. “C” Std. “C” Ext. Qty. Size Lugs a AL L-Rated 225 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 1 a 1 400 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 1 b 1 600 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 2 b 1 800 400 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 3 b 1 1000 600 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 4 b 1 1200 800 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 4 b 1 1350 1000 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 4 b 1 1600 1200 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 5 b 1 2000 1350,1600 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 6 b 2 2500 2000 27 (686) 28 (711) 32 (813) 20 (508) 24 (610) 8 b 2 3000 2500 27 (686) 28 (711) 32 (813) 20 (508) 24 (610) 9 b 2 3200 2000 29 (737) 28 (711) 32 (813) 20 (508) 24 (610) 9 b 2 4000 3000,3200 29 (737) 28 (711) 32 (813) 20 (508) 24 (610) 12 b 3 CU M-Rated 225 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 1 a 1 400 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 1 b 1 600 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 2 b 1 800 400 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 3 b 1 1000 — 13 (330) 25 (635) 29 (737) 17 (432) 21 (533) 4 b 1 1200 600 13 (330) 28 (711) 32 (813) 20 (508) 24 (610) 4 b 1 1350 800 13 (330) 28 (711) 32 (813) 20 (508) 24 (610) 4 b 1 1600 1000 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 5 b 1 2000 1200,1350 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 6 b 2 — 1600 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 5 b 1 2500 2000 18 (457) 28 (711) 32 (813) 20 (508) 24 (610) 8 b 2 3000 — 27 (686) 28 (711) 32 (813) 20 (508) 24 (610) 9 b 2 3200 — 27 (686) 28 (711) 32 (813) 20 (508) 24 (610) 9 b 2 4000 2500,3000,3200 27 (686) 28 (711) 32 (813) 20 (508) 24 (610) 12 b 3 5000 4000 29 (737) 28 (711) 32 (813) 20 (508) 24 (610) 15 b 4 Vertical End Tap Box Suffix ETVS (Standard) Suffix ETVX (Extended) a #6 AWG -350 kcmil, Cu/AI. b #4 AWG -600 kcmil, Cu/AI. c 24.0" (610mm) for isolated ground. Siemens Industry, Inc. SPEEDFAX Product Catalog 15-17
- Page 885 and 886: Low-voltage Switchgear Type WL Low
- Page 887 and 888: Low-voltage Switchgear WL Low-volta
- Page 889 and 890: Low-voltage Switchgear WL Low-volta
- Page 891 and 892: Type WL Low Voltage Metal-Enclosed
- Page 893 and 894: Type WL Low Voltage Metal-Enclosed
- Page 895 and 896: Type WL Low Voltage Metal-Enclosed
- Page 897 and 898: Type WL Low Voltage Metal-Enclosed
- Page 899 and 900: (559 m m ) (559 m m Type WL Low ) V
- Page 901 and 902: Type WL Low Voltage Metal-Enclosed
- Page 903 and 904: Type WL Low Voltage Metal-Enclosed
- Page 905 and 906: Type WL Low Voltage Metal-Enclosed
- Page 907 and 908: Switchboard Monitoring Sm@rtGear Mo
- Page 909 and 910: Low-voltage Switchgear Siemens Sm@r
- Page 911 and 912: Low-voltage Switchgear Type WL Low-
- Page 913 and 914: Low-voltage Switchgear Type WL Arc
- Page 915 and 916: Low-voltage Switchgear Arc Flash So
- Page 917 and 918: Low-voltage Switchgear Arc Flash So
- Page 919 and 920: Low-voltage Switchgear Arc Flash So
- Page 921 and 922: Busway Systems SPEEDFAX TM Section
- Page 923 and 924: Busway Systems Overview Busway Sele
- Page 925 and 926: Sentron Busway Systems Sentron Busw
- Page 927 and 928: Sentron Busway Systems Technical Da
- Page 929 and 930: Sentron Busway Systems Straight Sec
- Page 931 and 932: Sentron Straight Section Busway Cop
- Page 933 and 934: Sentron Busway Systems Elbows Revis
- Page 935: Sentron Busway Systems Revised on 0
- Page 939 and 940: NCBA Sentron Busway Systems Joint M
- Page 941 and 942: Sentron Busway Systems TBNK Fitting
- Page 943 and 944: Sentron Busway Systems Reducers and
- Page 945 and 946: Sentron Busway Systems Hangers Revi
- Page 947 and 948: Sentron Busway Systems Hangers and
- Page 949 and 950: Sentron Busway Systems Busway Acces
- Page 951 and 952: Sentron Busway Systems Flanged Ends
- Page 953 and 954: Sentron Busway Systems Cubicle Opti
- Page 955 and 956: Sentron Busway Systems Revised on 0
- Page 957 and 958: Sentron Busway Systems General Info
- Page 959 and 960: Sentron Busway Systems Siemens Sent
- Page 961 and 962: Sentron Busway Systems Programs and
- Page 963 and 964: Sentron Bus Plugs Sentron Bus Plug
- Page 965 and 966: Sentron Bus Plugs Circuit Breaker B
- Page 967 and 968: Sentron Circuit Breaker Bus Plugs B
- Page 969 and 970: Sentron Circuit Breaker Bus Plugs W
- Page 971 and 972: Sentron Busway Systems Fusible Bus
- Page 973 and 974: Sentron Fusible Bus Plugs Fusible B
- Page 975 and 976: Sentron Fusible Bus Plugs Wall Clea
- Page 977 and 978: Sentron SPD Bus Plugs Sentron SPD B
- Page 979 and 980: Sentron 3/6 Bus Plugs Sentron 3/6 B
- Page 981 and 982: 0 0 Sentron 3/6 Bus Plugs Rev Third
- Page 983 and 984: Surface Mount Receptacle Bus Plug (
- Page 985 and 986: XJ-L HD Busway System XJ-L HD Buswa
Sentron Busway Systems<br />
Tees<br />
Selection<br />
Tees are used to simplify directional and plane<br />
orientation changes in a busway system. Tees can<br />
make 90° bends left or right, and up and down along<br />
the busway run. All tees are supplied with two joint<br />
stack assemblies.<br />
15<br />
BUSWAY SYSTEMS<br />
Flatwise Tees, Dimensions (standard/min.)<br />
Dimensions Inches (mm)<br />
Ampere Rating<br />
“A”, ”B”, ”C”<br />
AL L-Rated<br />
225 — 12 (305)<br />
400 — 12 (305)<br />
600 — 12 (305)<br />
800 400 12 (305)<br />
1000 600 12 (305)<br />
1200 800 12 (305)<br />
1350 1000 12 (305)<br />
1600 1200 18 (457)<br />
2000 1350,1600 18 (457)<br />
2500 2000 18 (457)<br />
3000 2500 18 (457)<br />
3200 2000 18 (457)<br />
4000 3000,3200 24 (610)<br />
CU M-Rated<br />
225 — 12 (305)<br />
400 — 12 (305)<br />
600 — 12 (305)<br />
800 400 12 (305)<br />
1000 — 12 (305)<br />
1200 600 12 (305)<br />
1350 800 12 (305)<br />
1600 1000 12 (305)<br />
2000 1200,1350 12 (305)<br />
— 1600 18 (457)<br />
2500 2000 18 (457)<br />
3000 — 18 (457)<br />
3200 — 18 (457)<br />
4000 2500,3000,3200 18 (457)<br />
5000 4000 24 (610)<br />
Flatwise Tees<br />
Flatwise tees are used to create left and right branches.<br />
Flat Right<br />
Suffix TEFR<br />
Flat Left<br />
Suffix TEFL<br />
Edgewise Tees, Dimensions (standard/min.)<br />
Dimensions Inches (mm)<br />
Ampere Rating<br />
“D”<br />
AL L-Rated<br />
225 — 13 (330)<br />
400 — 13 (330)<br />
600 — 13 (330)<br />
800 400 13 (330)<br />
1000 600 13 (330)<br />
1200 800 18 (457)<br />
1350 1000 18 (457)<br />
1600 1200 18 (457)<br />
2000 1350,1600 18 (457)<br />
2500 2000 27 (686)<br />
3000 2500 27 (686)<br />
3200 2000 27 (686)<br />
4000 3000,3200 29 (737)<br />
CU M-Rated<br />
225 — 13 (330)<br />
400 — 13 (330)<br />
600 — 13 (330)<br />
800 400 13 (330)<br />
1000 — 13 (330)<br />
1200 600 13 (330)<br />
1350 800 13 (330)<br />
1600 1000 18 (457)<br />
2000 1200,1350 18 (457)<br />
— 1600 18 (457)<br />
2500 2000 18 (457)<br />
3000 — 27 (686)<br />
3200 — 27 (686)<br />
4000 2500,3000,3200 27 (686)<br />
5000 4000 29 (737)<br />
Edgewise Tees<br />
Edgewise tees are used to create branches that stem up or down<br />
from the busway run.<br />
Edge Up<br />
Suffix TEEU<br />
Edge Down<br />
Suffix TEED<br />
a<br />
a 12.0" (305mm) For Isolated Ground.<br />
15-16<br />
Siemens Industry, Inc. SPEEDFAX Product Catalog