Speedfax 2017
For Operation in the Control Cabinet 3RW Soft Starters 3RW30 for standard applications Characteristic curves Permissible installation height Operational rated current I in % e 105 100 95 90 85 80 75 70 0 1000 2000 3000 4000 5000 Mounting height in m At an installation height above 2000 m, the max. permissible operational voltage is reduced to 460 V. NSB0_01704 Soft Starter Control 17 CONTROL PRODUCTS More information Application examples for normal starting (Class 10) Normal starting Class 10 (up to 20 s with 300 % I n motor ), The soft starter rating can be selected to be as high as the rating of the motor used Application Conveyor belt Roller conveyor Compressor Small fan Pump Hydraulic pump Starting parameters • Voltage ramp and current limiting - Starting voltage % 70 60 50 40 40 40 - Starting time s 10 10 20 20 10 10 Note: These tables present sample set values and device sizes. They are intended only for the purposes of information and are not binding. The set values depend on the application in question and must be optimized during commissioning. The soft starter dimensions should be checked where necessary with the Win-Soft Starter software or with the help of Technical Assistance. 17-244 Siemens Industry, Inc. SPEEDFAX Product Catalog
For Operation in the Control Cabinet 3RW Soft Starters 3RW30 for standard applications Configuration The 3RW solid-state motor controllers are designed for easy starting conditions. In the event of deviating conditions or increased switching frequency, it may be necessary to choose a larger device. For accurate dimensioning, use the Win-Soft Starter selection and simulation program. If necessary, an overload relay for heavy starting must be selected where long starting times are involved. PTC sensors are recommended. In the motor feeder between the SIRIUS 3RW soft starter and the motor, no capacitive elements are permitted (e. g. no reactivepower compensation equipment). In addition, neither static systems for reactive-power compensation nor dynamic PFC (Power Factor Correction) must be operated in parallel during starting and ramp-down of the soft starter. This is important to prevent faults arising on the compensation equipment and/or the soft starter. All elements of the main circuit (such as fuses, controls and overload relays) should be dimensioned for direct starting, following the local short-circuit conditions. Fuses, controls and overload relays must be ordered separately. Please observe the maximum switching frequencies specified in the technical specifications. Note: When induction motors are switched on, voltage drops occur as a rule on starters of all types (direct starters, wye-delta starters, soft starters). The infeed transformer must always be dimensioned such that the voltage dip when starting the motor remains within the permissible tolerance. If the infeed transformer is dimensioned with only a small margin, it is best for the control voltage to be supplied from a separate circuit (independently of the main voltage) in order to avoid the potential switching off of the soft starter. Status graphs U U U N S ON 13/14 t R on t R on Win-Soft Starter selection and simulation program With this software, you can simulate and select all Siemens soft starters, taking into account various parameters such as mains properties, motor and load data, and special application requirements. The software is a valuable tool, which makes complicated, lengthy manual calculations for determining the required soft starters superfluous. The Win-Soft Starter selection and simulation program can be downloaded from: www.usa.siemens.com/softstarters > Software More information can be found on the Internet at: www.usa.siemens.com/softstarters t t NSB0_01941 Soft Starter Control Schematic circuit diagram L1 T1 A bypass contact system is already integrated in the 3RW30 soft starter and therefore does not have to be ordered separately. L2 T2 L3 T3 NSB0_01940 17 CONTROL PRODUCTS Siemens Industry, Inc. SPEEDFAX Product Catalog 17-245
- Page 1221 and 1222: Motor Starters, Soft Starters and L
- Page 1223 and 1224: For Operation in the Control Cabine
- Page 1225 and 1226: For Operation in the Control Cabine
- Page 1227 and 1228: For Operation in the Control Cabine
- Page 1229 and 1230: For Operation in the Control Cabine
- Page 1231 and 1232: Modules for RESET 1) Modules for re
- Page 1233 and 1234: For Operation in the Control Cabine
- Page 1235 and 1236: For Operation in the Control Cabine
- Page 1237 and 1238: For Operation in the Control Cabine
- Page 1239 and 1240: Planning and Configuration with SIR
- Page 1241 and 1242: Planning and Configuration with SIR
- Page 1243 and 1244: Planning and Configuration with SIR
- Page 1245 and 1246: For Operation in the Control Cabine
- Page 1247 and 1248: For Operation in the Control Cabine
- Page 1249 and 1250: For Operation in the Control Cabine
- Page 1251 and 1252: For Operation in the Control Cabine
- Page 1253 and 1254: Control Products Enclosed 3RW44 3RW
- Page 1255 and 1256: Control Products Enclosed 3RW44 3RW
- Page 1257 and 1258: Control Products Enclosed 3RW44 3RW
- Page 1259 and 1260: Control Products Enclosed 3RW44 3RW
- Page 1261 and 1262: Control Products Enclosed 3RW44 Enc
- Page 1263 and 1264: For Operation in the Control Cabine
- Page 1265 and 1266: For Operation in the Control Cabine
- Page 1267 and 1268: For Operation in the Control Cabine
- Page 1269 and 1270: For Operation in the Control Cabine
- Page 1271: For Operation in the Control Cabine
- Page 1275 and 1276: For Operation in the Control Cabine
- Page 1277 and 1278: For Operation in the Control Cabine
- Page 1279 and 1280: For Operation in the Control Cabine
- Page 1281 and 1282: For Operation in the Control Cabine
- Page 1283 and 1284: For Operation in the Control Cabine
- Page 1285 and 1286: For Operation in the Control Cabine
- Page 1287 and 1288: For Operation in the Control Cabine
- Page 1289 and 1290: For Operation in the Control Cabine
- Page 1291 and 1292: For Operation in the Control Cabine
- Page 1293 and 1294: For Operation in the Control Cabine
- Page 1295 and 1296: For Operation in the Control Cabine
- Page 1297 and 1298: For Operation in the Control Cabine
- Page 1299 and 1300: For Operation in the Control Cabine
- Page 1301 and 1302: For Operation in the Control Cabine
- Page 1303 and 1304: For Operation in the Control Cabine
- Page 1305 and 1306: For Operation in the Control Cabine
- Page 1307 and 1308: For Operation in the Control Cabine
- Page 1309 and 1310: For Operation in the Control Cabine
- Page 1311 and 1312: l For Operation in the Control Cabi
- Page 1313 and 1314: 3RW44 5. and 3RW44 6. for High-Feat
- Page 1315 and 1316: For Operation in the Control Cabine
- Page 1317 and 1318: For Operation in the Control Cabine
- Page 1319 and 1320: For Operation in the Control Cabine
- Page 1321 and 1322: For Operation in the Control Cabine
For Operation in the Control Cabinet<br />
3RW Soft Starters<br />
3RW30 for standard applications<br />
Characteristic curves<br />
Permissible installation height<br />
Operational rated current I in %<br />
e<br />
105<br />
100<br />
95<br />
90<br />
85<br />
80<br />
75<br />
70<br />
0 1000 2000 3000 4000 5000<br />
Mounting height in m<br />
At an installation height above 2000 m, the max. permissible operational<br />
voltage is reduced to 460 V.<br />
NSB0_01704<br />
Soft Starter<br />
Control<br />
17<br />
CONTROL<br />
PRODUCTS<br />
More information<br />
Application examples for normal starting (Class 10)<br />
Normal starting Class 10 (up to 20 s with 300 % I n motor ),<br />
The soft starter rating can be selected to be as high as the rating of the motor used<br />
Application Conveyor belt Roller conveyor Compressor Small fan Pump Hydraulic pump<br />
Starting parameters<br />
• Voltage ramp and current<br />
limiting<br />
- Starting voltage % 70 60 50 40 40 40<br />
- Starting time s 10 10 20 20 10 10<br />
Note:<br />
These tables present sample set values and device sizes. They<br />
are intended only for the purposes of information and are not<br />
binding. The set values depend on the application in question<br />
and must be optimized during commissioning.<br />
The soft starter dimensions should be checked where necessary<br />
with the Win-Soft Starter software or with the help of Technical<br />
Assistance.<br />
17-244<br />
Siemens Industry, Inc. SPEEDFAX Product Catalog