Parts Alliance Garage Essentials Winter 2020

Garage 

Essentials 

Issue 43 

Don’t get left out in the cold this winter... 

our affordable ZM Heater range will keep you nice and toastie 

MULTI-FUEL HEATERS 

FROM ONLY 

OFFERING high specification 

heaters, sourced direct 

from world-renowned 

factories, to the UK market 

at exceptionally low prices. 

The Z.M. Heater range is 

distributed exclusively into 

the automotive aftermarket 

by The Parts Alliance. 

SEE PAGES 4-7 FOR 

EXCLUSIVE OFFERS 

FROM ONLY 

£1295 SPACE HEATERS 

£249 

23% 

MORE HEAT 

THAN 

OTHER UNITS 

HOT & COLD WATER 

HIGH PRESSURE STEAM WASHER 

• Operating pressure / max 150/160 bar 

• Delivery rate 540 I/h 

• Motor pump type MPBX2/2800 RPM 

• Max outlet water temperature 140 o C 

• Three ceramic coated pistons, brass axial pump head 

with built-in by-pass valve 

• Vertical burner with high thermal efficiency steel coil 

• Temperature regulation guage 

• Detergent built-in tank for indirect suction 

PART NO: 

HDS7-10HCS / JESDHPSTEAM 

HOT & COLD WATER 

PRESSURE WASHER 

987AA8170 

• Built-in detergent tank 

• 150bar / 2175psi max output 

• 570l / min max flow rate 

• 90 degree max water temperature 

• Brass pump head and ceramic 

• Vertical burner with highly efficient steel coil 

• Steel reinforced professional 8m hose 

• High pressure/ low pressure adjustable lance 

PART NO: 

HDS6-12HC / JESDPHW 

NORMALLY 

£ 

2,195 

NOW ONLY 

£ 

1,795 

NORMALLY 

£ 

1,295 

NOW ONLY 

£ 

995 

Weekly from: £9.53† Weekly from: £5.28† 

Enquiries: 0121 749 8801

Excellence in Automotive 

Component Distribution 

Branches 

Branches / Contents 

ALLPARTS BRANCHES 

AYLESBURY 01296 737873 

ENFIELD 020 8443 8090 

HAYES 020 8573 0033 

HEMEL HEMPSTEAD 01442 868040 

HIGH WYCOMBE 01494 441234 

OXFORD 01235 550555 

SLOUGH 01753 215080 

WATFORD 01923 239039 

BBC SUPERFACTORS 

BRANCHES 

ACCRINGTON 01254 239911 

BLACKBURN 01254 53463 

BLACKPOOL 01253 843373 

BURNLEY 01282 450005 

CHORLEY 01257 233833 

CLITHEROE 01200 425525 

PRESTON 01772 281711 

BMF BRANCHES 

BROMSGROVE 01527 575444 

KIDDERMINSTER 01562 864333 

MALVERN 01684 882699 

REDDITCH 01527 520445 

WORCESTER 01905 29990 

BMS BRANCHES 

BURY 01617 614012 

DUKINFIELD 01613 396500 

OLDHAM 01616 268384 

ROCHDALE 01706 678000 

CES BRANCHES 

AINTREE 0151 525 1764 

ANGLESEY 01248 422000 

BURTON 01283 500 006 

CAERNARFON 01286 673504 

CANNOCK 01543 431 400 

CHESTER 01244 377118 

CREWE 01270 214216 

DERBY 01332 202802 

HALESOWEN 0121 561 3001 

ISLE OF MAN 01624 620000 

LIVERPOOL 0151 2076667 

LLANDUDNO 01492 592144 

MACCLESFIELD 01625 427733 

MANCHESTER (SOUTH) 0161 946 7929 

NORTHWICH 01606 353200 

PORTHMADOG 01766 515414 

RHYL 01745 355505 

SHREWSBURY 01743 440088 

SOUTHPORT 01704536446 

STOKE 01782 844395 

TELFORD 01952 581666 

WIDNES 0151 424 5056 

WOLVERHAMPTON 01902 350940 

WREXHAM 01978 365392 

CAR PARTS & ACCESSORIES 

BRANCHES 

BURGESS HILL 01444 258831 

CHICHESTER 01243 771331 

EAST GRINSTEAD 01342 321456 

EASTBOURNE 01323 410817 

HASLEMERE 01428 654444 

HENFIELD 01273 495880 

HORSHAM 01403 257325 

HOVE 01273 701777 

LEWES 01273 487828 

LITTLEHAMPTON 01903 719990 

WORTHING 01903 823123 

DINGBRO BRANCHES 

ABERDEEN 01224 682000 

ARBROATH 01241 876414 

AYR 01292 266400 

BATHGATE 01506 633335 

BELLSHILL 01698 744328 

CARLISLE 01228 584888 

DUMBARTON 01389 317700 

DUMFRIES 01387 270250 

DUNDEE 01382 643000 

DUNFERMLINE 01383 748210 

EAST KILBRIDE 01355 236500 

EDINBURGH (GYLE) 0131 453 8360 

EDINBURGH (LEITH) 0131 657 6464 

ELGIN 01343 552888 

FALKIRK 01324 677100 

FRASERBURGH 01346 512345 

GALASHIELS 01896 664800 

GLASGOW 0141 554 9998 

GREENOCK 01475 552556 

INVERNESS 01463 236686 

KILMARNOCK 01563 591800 

KIRKCALDY 01592 654212 

MONTROSE 01674 675311 

PAISLEY 0141 887 2033 

PERTH 01738 443388 

PETERHEAD 01779 476551 

STIRLING 01786 463300 

STRANRAER 01776 705777 

GMF BRANCHES 

BRIDGEND 01656 649493 

CAMARTHEN 01267 237977 

CARDIFF (NORTH) 02920 628686 

CARDIFF (EAST) 02920 489150 

CHELTENHAM 01242 252100 

COLEFORD 01594 832092 

GLOUCESTER 01452 528800 

HAVERFORDWEST 01437 760428 

LLANELLI 01554 775772 

MERTHYR 01443 699002 

NEATH 01639 641118 

NEWPORT 01633 280001 

ROSS ON WYE 01989 769921 

SWANSEA 01792 790080 

GSF CAR PARTS 

BRANCHES 

ANDOVER 01264 839999 

BANBURY 01295 221133 

BASINGSTOKE 01256 710200 

BELFAST 028 9066 3866 

BIRMINGHAM 0121 749 8815 

BRADFORD 01274 652020 

BRISTOL (NORTH) 0117 322 4078 

BRISTOL (CENTRAL) 0117 9557 654 

BRISTOL (SOUTH) 0117 338 0380 

CAMBRIDGE 01223 640999 

CANTERBURY 01227 811088 

CARDIFF 029 2034 7900 

CHELMSFORD 01245 460460 

CHELTENHAM 01242 225620 

COLCHESTER 01206 203006 

COVENTRY 024 7666 9988 

DAVENTRY 01327 871009 

DERBY 01332 346680 

DONCASTER 01302 762762 

DUBLIN (NORTH) 01 862 2884 

DUBLIN (SOUTH) 01 460 6062 

FARNHAM 01252 333891 

GLOUCESTER 01452 212212 

HARLOW 01279 342200 

HARROW 020 8960 8182 

HEATHROW 020 8917 3800 

HUDDERSFIELD 01484 434333 

IPSWICH 01473 748166 

KINGSTON 020 8547 3101 

LEAMINGTON SPA 01926 451980 

LEEDS (EAST) 0113 201 9030 

LEEDS (WEST) 0113 244 3637 

LEICESTER 0116 234 0200 

LETCHWORTH 01462 708800 

LINCOLN 01522 575333 

LUTON 01582 506940 

MANSFIELD 01623 594900 

MILTON KEYNES 01908 872278 

NORTHAMPTON 01604 609080 

NORWICH 01603 780900 

NOTTINGHAM 01159 503723 

OXFORD 01865 972 972 

PETERBOROUGH 01733 293444 

PLYMOUTH 01752 330011 

POOLE 01202 741060 

PORTSMOUTH 02392 728970 

READING 01189 873030 

ROMFORD 0208 598 8800 

SHEFFIELD 01142 617888 

SITTINGBOURNE 01795 402402 

SMETHWICK 0121 565 6340 

SOUTHAMPTON (WEST) 023 8086 3900 

SOUTHAMPTON (NORTH) 0238 124 2636 

SOUTHEND-ON-SEA 01702 277 969 

STAPLES CORNER 020 8208 6444 

SWINDON 01793 836940 

THURROCK 01708 890740 

TORQUAY 01803 242400 

TOTTENHAM 020 8104 8020 

TRAFFORD 0161 876 0466 

WATFORD 01923 229255 

WOODFORD GREEN 0203 2802611 

SAS AUTOPARTS BRANCHES 

BRADFORD 01274 733 888 

CASTLEFORD 01977 558 833 

DURHAM 0191 336 1990 

GOOLE 01405 658031 

HARROGATE 01423 889 021 

LEEDS 0113 292 4999 

MIDDLESBROUGH 01642 386477 

NEWCASTLE 0191 204 9555 

NEWCASTLE EAST 0191 205 8313 

NORTHALLERTON 01609 779 551 

OTLEY 01943 467 514 

SKIPTON 01756 799 500 

SUNDERLAND 01916 444789 

YORK 01904 829 239 

SC MOTOR FACTORS 

BRANCHES 

ASHFORD 01233 502379 

CROYDON 0208 970 7734 

DOVER 01304 210712 

FOREST HILL 020 8314 4750 

HASTINGS 01424 435588 

MAIDSTONE 01622 766410 

SIDCUP 020 8302 7624 

STROOD 01634 712212 

THANET 01843 298676 

TUNBRIDGE WELLS 01892 518028 

WELLING 020 8317 7774 

THE PARTS ALLIANCE 

BRANCHES 

BARNSTAPLE 01271 375801 

CHARD 01460 65051 

EXETER 01392 258279 

FROME 01373 465961 

INDIAN QUEENS 01637 849377 

PENRYN 01326 372651 

PLYMOUTH 01752 668931 

TAUNTON 01823 259691 

TIVERTON 01884 256767 

WESTON 01934 886544 

WEYMOUTH 01305 360875 

WATERLOO BRANCHES 

BEVERLEY 01482 871771 

BRIDLINGTON 01262 400900 

HULL 01482 328308 

Find Us On 

CAPITAL EQUIPMENT 

AIR COMPRESSORS 

ABAC 60-69 

AIR CONDITIONING 

Denso 20-22 

AFT CLEANER & FLUID 

Powatec 64 

MOT EQUIPMENT 

Crypton 26 & 27 

Tecalemit 12 & 15 

VEHICLE LIFTS 

Atlas 15 

EAE 10-11 

Tecalemit 16-17 

DIAGNOSTICS 

VEHICLE DIAGNOSTICS 

Autel 38-39 

Bendix 41-43 

Bosch 44-47 

Crypton 26-27 

Delphi 34-35 

Draper 44 

Maverick 36-37 

Powatec 65 

Texa 30 

VDO 28 

VCDS Vag-Com 29 

HEATERS 

ZM Heaters 7-9 

SPRAY BOOTHS 

Rowley 40 

WHEEL & TYRE 

Atlas 12-14 

EAE 11 

Tecalamit 18-19 

WHEEL & TYRE 

WHEEL ALIGNMENT & ADAS 

Atlas 13-14 

Bendix 41-43 

Tecalemit 19 

WORKSHOP EQUIPMENT 

BATTERY CHARGERS / TESTERS 

GYS 23 

Lemania Energy 49 

SIP 50 

BOTTLE JACKS / TRANSMISSION JACKS / 

TROLLEY JACKS / JACKING BEAMS / 

AXLE STANDS 

Draper 52 

Laser Tools 56 

Liftmaster PAGE 19 

Sealey Tools 54 

CHEMICALS 

CTR 20-22 

Powatec 64 

HAND / WORKSHOP TOOLS / HYBRID 

Bendix 41-43 

Carbon - Clean 32-33 

Draper 52-53 

Laser Tools 56-59 

Milwaulkee 67-72 

Sealey Tools 54-55 

LIGHTING 

Unilite 66 

PRESSURE WASHERS / VACUUM 

CLEANERS 

DeWALT 25 

Karcher 8-9 

SIP Cleaners 24 

WELDING 

SIP & Helvi 48 

GAS EXTRACTION 

AER Services 51 

Dingbro Ltd 

2 Garage Essentials - For the best Choice, Quality, Service & Expertise 

3



Z.M. Heaters - Exclusive to Parts Alliance 

Z. M. Heaters - Exclusive to Parts Alliance 

PART NO: ZM-135T 

ZM135-T Manual Dual Fuel Heater with Flue Kit 120,000 Btu/hr 

All the proven features of the ZM-130 but with these 4 great additions: 

PART NO: 987AA720K 

WITH FLUE KIT 

£ 

1,495 

Weekly from: £7.94† 

PART NO: 987AA7200 

WITHOUT FLUE KIT 

£ 

1,295 


ZM-130 32kW 110,000 Btu 

Multi Fuel Heater 

Reliable, efficient, versatile heating 

for smaller sized workshops 

• ‘Plug and play’ 220-240V power supply 

• With built-in fuel storage tanks 

• Simple control panels with unique 5x LED 

operating function display 

• Fully variable output control 

• Blower fans for the winning combination 

of radiant heat and air circulation 

• Multi-fuel – waste engine oil, hydraulic oils, red diesel, 

diesel or bio-fuels can all deliver clean, efficient workshop 

heat 

• Up to 90% efficient – with the ‘Heater Booster’ 

• Fast & free UK delivery – arrives in just 2 to 3 working days 

• Draft stabilisers included – simply add / connect to 150mm 

flue 

• Safety controls – overheat and overflow protection switches 

• Cleaning pan included - to quickly scrape and clean away 

any soot 

ZM-150 52kW 177,000 Btu 

Multi Fuel Heater 

This heater boasts class-leading 

features including 75 litre fuel tank, 

massive 52kW maximum heat output, 

high capacity blower fan and unique 

built-in heat exchanger. 

177,000 Btu of heat 52 kW, 

clean and affordable! 

THESE HEATERS ARE 

EUROPEAN MADE 


WITH FLUE KIT 

£ 

1,995 




£ 

1,795 


SEALED COMBUSTION 

CHAMBER FOR INCREASED 

SAFETY. NO WORKSHOP 

SMOKE OR ODOURS 


WITH FLUE KIT 

£ 

1,575 




£ 

1,395 


• Combustion fan - for faster heat-up and 

cleaner burn (can be ducted to draw 

outside air) 

• New grille design - for even more airflow 

and increased heater efficiency 

• Higher output range - 19-35kW / 65,000- 

120,000 Btu - from max 3.5 litres per hr fuel 

Z.M. AUTOMATIC 

MULTI FUEL HEATERS 

• ‘Plug and play’ 220-240v supply 

• 55 litre fuel tank 

• Fully variable heat output 

• 1,000 m 2 /hr blower fan 

• Multi fuel capability 

• Inc. draft stabiliser & cleaning pan 

• Free delivery 

ZM Heaters have added a range of 90% efficient, auto-ignition 

warm air blowing cabinet heaters for the 2017/2018 season 

• Designed for multiple fuels - with resistant 

stainless steel combustion chambers and 

heat exchangers, with easy access to clean 

• Quality components - inc Soler & Palau 

centrifugal 

fans and Honeywell double-limit fan 

thermostats 

• Rugged construction - simple design using 

strong materials, for longer operating life 

• Supplied with European oil burner - 

Citerm JUNIOR or G-series burners included 

• Connecting hoses included - supplied with 

either floating pick-up or in-line filter 

• Safety controls - all burners have overheat, 

overflow and flame-out protection included 

• Push button control - turn on / off or add 

a room thermostat / timer 

control remotely 

• Lower maintenance - higher burning 

temperatures reduce cleaning frequency 

• 12 months warranty 

170kW Automatic Heater 

also available - POA! 

Features Units Z-45 Z-80 Z-120 

Rating (gross / nett) Btu/hr 143,000 307,000 460,000 

Power supply V 220-240 (single phase) 400 (3 phs) 

Power intake kW .25 .37 1.1 

to 

RUNS ON 

MULTIPLE FUELS 

HEATER 

BOOSTERS 

Specifications compared: 

Boost the efficiency of your 

Heater by 40%. 

Just add a Heater Booster 

The heater booster is an in-line multipass stainless steel flue gas heat 

exchanger which can raise efficiency on HP heaters to over 90%. This means 

over 40% more heat is realised from your fuel that would otherwise be lost up 

the flue. A 220-240v supply is required for the fan. The booster simply slots onto 

any 150mm flue sector before the flue. The heat outlet can be ducted if required 

(see as illustrated). 

ZM-130 

ZM-150 

NEW LOWER PRICES NOW SAVE 12% NOW SAVE 5% 

Output range kW (Btu) 17 – 32 (58,000 – 110,000) 30 – 52 (102,000 – 177,000) 

Weight 80 kg 115 kg 

Dimensions H x W x D - cm 137 x 58 x 87 147x 70 x 100 

Max fuel usage 3.3 litres per hour 5.2 litres per hour 

Air flow 1,000 m2 per hour 5,400 m2 per hour 

Tank capacity 50 litre 75 litre 

Warranty as standard 2 years 2 years 

IMPROVES 

HEATER 

EFFICIENCY 

BY 40% 

987AA7240 

£ 

299 

*2 Year Warranty Terms - covers sudden or unforeseen failures on a parts-only basis, specifically excluding burner dishes and thermostats, which are consumable 

items each carrying 6 months goodwill warranty from date of heater purchase. For full details: http://www.zmosystems.co.uk/trading-terms-conditions. 

• UK-manufactured stainless steel flue kits from just £245 

+ VAT for a basic 5m kit. Need to exit a rear wall and 

not sure what you need? Want to add a roof seal? - No 

problem! All our flue kits are sourced to order from 

manufacturer - delivering exactly what you need. 

• Heater Booster inline stainless-steel heat exchanger will 

recover heat that would be lost back into the workshop 

only £299+ VAT when ordered with a heater. The booster 

adds 270 m2 per hour air flow from 80mm twin outlets 

(dimensions: H 61cm x W 37cm x D 42cm and 8.7 kg 

weight). 

Airflow m 2 per hour 2,900 m 2 per hour 4,500 m 2 per hour 7,900 m 2 per hour 

Width x Depth x Height cm 46 x 75 x 160 61 x 81 x 195 61 x 101 x 195 

Flue ø mm 115 (5”) 154 (6”) 154 (6”) 

Price inc delivery £ £3,995 £4,495 £5,595 

HOW MUCH HEAT 

DO I NEED TO GENERATE? 

Here is your step by step guide for 

working out how much heat you need. 

A. Area to be heated, length.....feet, width.....feet, average height.....feet 

B. Multiply, length x width x average height = volume.....cubic feet 

C. Select the description which best suits the area to be heated from the table 

below and fill in the appropriate Btu/cu.ft figure here..... 

D. Multiply the volume from B.....Cubic feet by the figure from C.....Btu/cu.ft 

= Total heat required.....Btu/hour 

The amount of Btu/cu.ft required is dependent on the insulation of the building 

and the average ambient temperature prevailing in the area where the building 

is situated. A building with no insulation in the area that experiences extremely 

adverse weather conditions may require up to 9 Btu per cu.ft 

For general calculation we recommend 5 Btu per cu.ft. 

* 1 cubic metre = 35 cubic feet 

Weekly from: £ 21.20† Weekly from: £ 23.86† Weekly from: £ 29.70† 

A comfortable working temperature is not only essential for people to 

work safely and productively it is a legal requirement. The amount of 

heat required to give comfortable working conditions depends on several 

factors, the most important are: 

• The standard of insulation in your building 

• How much warm air escapes through frequently opened doors 

• The outside temperature 

• 15 C˚/59˚ F is a comfortable temperature for people who are 

moving about and so generating some body heat 

• Calculations are based on a Delta T of 20˚C, i.e. an ambient 

temperature of -5˚C and a required temperature of +15˚C 

Which description best fits the building? 

or area that you want to heat? 

A No insulation (e.g. corrugated sheet), doors frequently opened 9 Btu/cu.ft 

B Poor insulation (e.g. single skin brick/block), single glazed windows, opened fairly often 6,8 Btu/cu.ft 

C Average insulation (e.g. double skin brick/block), single glazed windows, roof insulated 5 Btu/cu.ft 

D Good insulation (e.g. blocks/cladding/insulation between), few or double-glazed windows 2,7 Btu/cu.ft 

w 

? 

L 

? 

Dingbro Ltd 


5





SUPER QUIET 

PORTABLE PARAFFIN 

DIESEL SPACE HEATERS 

PART NO: ZMQ-K125 

987AA7280 

NORMALLY 

£ 

395 

NOW ONLY 

£ 

325 

125,000 BTU 

POWERFUL 

& DURABLE 


987AA7270 

NORMALLY 

£ 

349 

NOW ONLY 

£ 

249 

70,000 BTU 

26% more 

Heat than 

other units 

23% more 

Heat than 

other units 

PART NO: ZMIR-K60 

987AA7250 

NORMALLY 

£ 

495 

NOW ONLY 

£ 

395 

60,000 BTU 

145,000 BTU 

PART NO: ZMID-K135 

987AA7260 

NORMALLY 

£ 

695 

NOW ONLY 

£ 

529 

• 987AA7250 

‘Available from Jan/Mar Z.M. Infrared heater - very 

efficient low cost heating’ 

• 987AA7270 

‘Available from Jan/Mar Z.M. Indirect heater - connect to a 

flue to get all the heat and none of the fumes’ 

Watch our 

video to find 

out more 

https://youtu.be/umJILm8yu54 

Z.M. Heaters offer high specification heaters, sourced 

direct from world-renowned factories, to the UK market 

at exceptionally low prices. The Z.M. Heater range is 

distributed exclusively into the automotive aftermarket by 

The Parts Alliance. 

Z.M. Heaters keep things simple with UK manuals written 

in plain English and fast support, with spares in stock and 

experienced engineers. 

987AA7270 987AA7280 987AA7290 

Output kW (Btu) 20kW (70,000) 36kW (125,000) 51kW (175,000) 

Weight 12 kg 24 kg 27 kg 

175,000 BTU 


987AA7290 

NORMALLY 

£ 

495 

NOW ONLY 

£ 

375 

Portable Heavy Duty Paraffin 

Kerosene Space Heaters 

Powerful, durable heaters offering significantly better heat. Sourced from 

a world-leading factory,this range offers better quality and reliability than 

many other heaters that will cost far more. 

• Quick, cost-effective heat, no installation, 

near-100% efficiency 

• Run on diesel, red diesel, paraffin or heating oils 

987AA7250 

987AA7260 

• Supplied with UK 220-240V mains plug 

• Built-in variable thermostat control 

for auto on / off cycling 

• Digital room temperature read-out with 

built-in diagnostics (not on ZMQ-K70 only) 

• Full safety controls include 

flame-out and overheat shut-down 

• UK manual including service procedures, 

trouble-shooting, parts diagrams etc 

• Fast delivery – typically delivered next working day 

• 12 months warranty - spares & service parts in UK stock 

Max fuel usage 1.9 litres per hour 3.6 litres per hour 4.9 litres per hour 

Air flow 400 m3 per hour 900 m3 per hour 1,100 m3 per hour 

Output kW (Btu) 17.6kW (60,000) 42.5kW (145,000) 

Weight 13.5kg 42kg 

MADE IN 

SOUTH 

KOREA 

Tank capacity 19 litre 38 litre 50 litre 

Move with Carry handle Trolley & wheels Trolley & wheels 

Watch our 

video to find 

out more 

Max fuel usage 1.7 litres per hour 4.2 litres per hour 

Air flow 100 m3 per hour 1,500 m3 per hour 

Tank capacity 13 litre 49 litre 

Please visit: www.zmosystems.co.uk 

https://youtu.be/umJILm8yu54 

Move with Carry handle Trolley & wheels 

Dingbro Ltd 


7



Karcher 

Karcher 

HDS 7/10-4 M 

With water flow of up to 700 litres per hour, and up to 100 bar pressure, the 7/10 is 

a great all-round machine with superb performance for daily and deep cleaning jobs. 

• Voltage: 240v 

• Flow rate (l/h): 350-700 

• Pressure bar / MPa 30-100 / 3-10 

• Max. temperature ˚C 155 

• Power rating kW 3, 4 

• Consumption fuel oil kg/h 4, 6 

• Fuel tank l 25 

• Weight kg 146 

• Dimensions (L x W x H) mm 1330, 750, 1060 

PART NO: HDS7/10-4M 

ONLY 

£ 

2,695 


HDS 6/12 C 

Single-phase (240 V) HDS 6/12 C hot water high-pressure 

cleaner with eco!efficiency mode, EasyForce trigger gun 

and Servo Control; The infinitely variable pressure and 

water flow regulation function from Kärcher. 

• Current type (Ph/V/Hz) 1 / 240 / 50 

• Flow rate (l/h) 240 - 560 

• Operating pressure (bar/MPa) 30 / 120 / 3 / 12 

• Max. temperature (°C) 80 - 155 

• Power rating (kW) 3 

• Consumption fuel oil (kg/h) 3.5 

• Fuel tank (l) 15 

• Weight (kg) 107.4 

• Dimensions (L x W x H) (mm) 1060 x 650 x 920 

PART NO: HDS6/12C 

ONLY 

£ 

1,995 


HD 6/13 

The new HD 6/13 C Plus from Kärcher features 

a host of benefits to make cleaning jobs that little 

bit quicker and easier. Typical Kärcher design 

features add convenience without compromising 

performance: like the on-board storage for 

nozzles, power cable, hose and lance; the new 

carry handle that makes the machines truly 

portable; and of course the unique lie-flat or 

stand up operating position. 

• Current type (Ph/V/Hz) 1 / 230 / 50 

• Flow Rate (l/h) 590 

• Operating pressure (bar/MPa) 130 / 13 

• Max. Pressure (bar/MPa) 190 / 19 

• Power rating (kW) 2.9 

• Power cable (m) 5 

• number of simultaneous users 1 

• Mobility ultra 

• Weight (with accessories) (kg) 26.2 

• Weight incl. packaging (kg) 28.6 

• Dimensions (L x W x H) (mm) 

380 x 360 x 930 

PART NO: HD6/13 

ONLY 

£ 

595 

BR 40/10 C ADV 

• Powerful and fast 

• Two high-speed roller brushes with high 

contact pressure 

• Two squeegees remove water forwards 

and backwards 

• Floors dry very quickly 

• Low reach 

• Easily reaches under furniture 

• The push handle can folded in both 

directions 

• Removable tank - suitable for low lying 

objects 

• Service-friendly 

• Squeegee and brush are easy to replace 

without tools 

• Water distributor strip is easy to remove 

and clean 

• All electrical components are quickly and 

easily accessible 

• Ergonomic handle 

• For easier use 

• With integrated water flow and brush 

control 

• Ideal for transporting and storage 

PART NO: BR40/10CADV 

ONLY 

£ 

1,795 


WORKING WIDTH: 400MM 

BRUSH SPEED: 1100 RPM 

FRESH/DIRTY WATER TANK 

10/10 LITRES 

KM 70/20 

The KM 70/20 C is a high-value push sweeper with professional build-quality and 

a range of professional features. Sweeping 7 x faster than a conventional broom, 

the 70/20 dramatically reduces dust and guarantees consistent, thorough results. 

Featuring an adjustable side brush for cleaning right up to kerb edges. Ideal for 

cleaning paths, halls and warehouses quickly and efficiently. The 20 litre hopper 

is very easy to empty and both main and side brushes are fully adjustable to suit 

different surfaces. The machine folds flat for easy storage. 

• Drive Manual 

• Max. Area Performance (m²/h) 2800 

• Working width (mm) 480 

• Working width with 1 side brush (mm) 700 

• Container capacity gross/net (l) 42 / 20 

• Weight (with accessories) (kg) 22 

• Weight, ready to operate (kg) 23 


• Dimensions packaging (L x W x H) (mm) 

795 / 400 / 935 

• Dimensions (L x W x H) (mm) 

1300 x 765 x 1035 

NT 27/1 

The NT27/1 is a robust and powerful all-purpose 

vacuum cleaner designed for professional 

applications and perfect for the automotive 

industry supplied with inter-changeable floor tool 

for wet or dry use, and a sock to protect the filter 

when picking up liquids. Perfect for cleaning 

vehicles, workshop spills and more. 

• Capacity: 27 litres 

• Air Flow: 67 litres/sec 

• Power: 1380W (240V) 

PART NO: NT27/1 

ONLY 

£ 

195 

NT 48/1 

The NT 48/1 is a high-capacity single motor 

all-purpose vacuum cleaner for picking up large 

quantities of wet or dry dirt. It is fitted with an 

automatic cut out facility for when maximum fluid 

capacity is reached and a drainage hose for the 

disposal of all liquids in a safe and clean manner. 

• Current type (Ph/V/Hz) 1 / 110 - 110 / 

50 - 60 

• Air flow (l/s) 67 

• Vacuum (mbar/kPa) 200 / 20 

• Container capacity (l) 48 

• Container material Plastic 

• Motor rating (W) 1380 

• Cable length (m) 7.5 

• Sound level (dB(A)) 72 

• Weight without accessories (kg) 10.5 


• Dimensions (L x W x H) (mm) 770 x 390 

x 485 

PUZZI 8/1 

The powerful and compact Puzzi. 8/1C enhances Kärcher’s spray extraction 

range as it is ideal for upholstery cleaning of carpeted floors. Due to the 

excellent suction power, the Puzzi 8/1 C leaves carpets and upholstery 

virtually dry to touch in minutes. It’s lightweight construction means this unit 

can be transported easily from one place to another perfect for use in hotels, 

hospitals, shops and the automotive industry. 

• Spray Rate: 1 litre per minute 

• Air Flow: 61 litres per minute 

• Fresh/Dirty water capacity: 8/7 litres 

PART NO: KM70/20 

ONLY 

£ 

550 

PART NO: HT48/1 

ONLY 

£ 

249 

PART NO: PUZZI-8/1 

ONLY 

£ 

425 

Dingbro Ltd 


9



EAE 

NEW EAE 5 year 2+2 warranty: the equipment will be covered for a 5 year structure 2 year hydraulic and 2 year electrical parts* 

STANDARD WHEEL ALIGNMENT 

FOUR POST LIFT 

• 4000Kg / 5000Kg lifting capacity 

• Long slip plate and adjustable turntable positions for 

alignment use 

• Reliable mechanical safety locking system 

• Avoid rapid descending cause by leakage of hydraulic 

system by applying FLOW-CONTROL technique to 

hydraulic system 

• Max height switch limits the travel of runways 

and ensures cylinders work within the stroke 

• The alarm buzzer for safe descending 

• 24V safety control voltage 

• Reliable electrical release for easy and efficient use 

• Compact quick plug electrical connection releases 

installers from too many wires and terminals and 

make initial installation much more efficient. 

Save more than 70% time on wire connection 

• Low profile runway is convenient for driving 

on and off and less demanding on space 

• Optional rolling jack 

ELECTRICAL SAFETY 

LOCK RELEASE SYSTEM 

with two optional 

rolling jacks 

3 TONNE AIR OPERATED 

JACKING BEAMS ARE 

ALSO AVAILABLE 

FOR JUST 

PART NO: EE-CJ354 

ONLY 

£ 

880 

TYRE CHANGER & 

WHEEL BALANCER 

PACKAGE DEAL 

EE-4880ID 

Tyre Changer 

• Pneumatically operated tilting column 

• Simultaneous pneumatic horizontal 

and vertical arm locking 

• Pneumatic bead breaker 

• Durable and convenience operation 

• Tilting column and pneumatic 

locking system 

• Bigger bead breaker cylinder 

ø200, more powerful 

• CE certified 

EE-4880ID Tyre Changer 

Rim material: Steel, Al., Alloy 

EE-3096AV2 

Wheel Balancer 

• CE certified 

• For passenger car, motorcycle and 

light commercial vehicle wheels 

• Hand-operated distance and wheel diameter 

input 

• Various balancing modes 

• Self-calibration and diagnosis 

• Plastic safe-guard works as the START and STOP 

• Optional centreless wheel adapter, 

motorcycle adaptor and ltruck 

and van cones 

EE-3096AV2 Wheel Balancer 

Max. wheel weight 65KG 

FANTASTIC 

PACKAGE!! 

EAE 

Package Deal 

£ 

2,595 


Model No. 

Lifting Capacity: 

Max. Lifting Height: 

Min. Lifting Height: 

Lifting Time: 

Air Supply: 

Capacity of Motor: 

Electricity Supply: 

EE-6435V2.B 

4000kg / 5000kg 

1830mm 

180mm 

40 seconds 

6-8 bar 

3.5kW 

According to customer needs 

PART NO: 

EE-6435V2B48L 

4.0 Tonne 

£ 

5,995 


PART NO: 

EE-6435V2B52L 

5.0 Tonne 

£ 

6,595 


Max. wheel diameter: 45” 

Motor Power: 0.2kw 

Max. wheel width: 14” Rim diameter: 10”-24” 

Outer clamp: 12”-23” Rim width: 1.5”-20” 

Motorcycle clamp: 12”-26” 

Balancing speed: 220RPM 

Power supply: 110V/220V/380V 

Balancing accuracy: 1g 

Motor power: 0.75KW/1.1KW 

Power supply: 220V 

Air supply: 8-10Bar 

Noise level:



Atlas and Atlas Platinum Garage Equipment 


UNBEATABLE TYRE PACKAGE OFFERS 

PTC420 26” 

TYRE CHANGER 

£ 

4,995 


ATLAS TC220 PLUS & 

WB12 TYRE PACKAGE 

Representing unbeatable value, this highly capable tyre 

package provides a sensible entry-level investment 

without compromising on key features. 

With a reputable brand name and comprehensive installation 

and training, the TC220 Plus and WB12 combo is 

the perfect choice for anyone looking to get into 

tyres, ensuring they have the equipment to 

allow their tyre business to grow. 

TC220 PLUS – £1,795 

WB12 – £995 

COMBO PRICE £ 

2,395 


FULL 

INSTALLATION 

& TRAINING 

INCLUDED 

LIMITED EDITION 

‘TORNADO’ TYRE PACKAGE 

Consisting of a Fully-Automatic Tyre Changer with 3-Way 

assist arm, and compact yet heavy-duty Motorised Wheel 

Balancer, this Italian-designed combo comes with the 

full-spectrum support you’d expect from the Atlas team, 

including delivery, installation and the peace of mind from 

a 12 months on-site parts and labour warranty from a 

nationwide team of expert technicians. 

• 10”–24” clamping (22” external) 

• Pneumatic Assist arm for handling difficult tyres 

• One of the UK’s best-selling wheel balancers 

• Both machines single phase operating from 

3-pin plug 

TORNADO TC – 

£2,095 

TORNADO WB – 

£945 

Now includes 

LED 

ILLUMINATION 

onto inside of 

rim! 

COMBO 

PRICE 

£ 

2,695 


PWB50 


AUTOMATIC 2D WHEEL BALANCER 

WITH DIGITAL DISPLAY 

Premium quality Italian engineering and advanced 

features means you shouldn’t be fooled by the 

PWB50’s compact appearance. Automatic data 

entry (2D), Split Weight function for hiding weights 

discreetly behind rim spokes, and the automatic 

weight placement arm for guaranteed first time zero/ 

zero balancing demonstrate the capability of this 

premium balancer. 

• Handles rims up to 30” diameter 

• 2D Automatic Data Entry 

• Automatic guidance to weight location using 

weight placement arm 

• ‘Split-Weight’ function 

• Compact yet feature-packed 

• 2 Year Warranty 

£ 

1,795 


PWB90 


FULLY AUTOMATIC TYRE CHANGER WITH 

ASSIST ARM 

A super heavy duty tyre changer that is designed for alloy 

wheel specialists or fast fit professionals and built to last. 

Over-engineered structure and 3-way Robotic Arm ensure 

this machine is capable in the toughest of environments. 

• Clamping up to 26” diameter rims 

• Fully-Automatic Operation 

• Ergonomic positioning of bead breaker pedal 

• 3-Way Robotic Assist Arm 

• Super Heavy Duty build quality 


£ 

3,295 


£250 

OFF 

when you purchase 

any combination 

package 

Includes 

2 YEARS 

On-Site 

WARRANTY 

£ 

2,695 


PTC520 30” 

TYRE CHANGER 

SUPER AUTOMATIC CENTRE POST 

LEVER-LESS TYRE CHANGER 

The ultimate in Atlas Platinum tyre fitting technology, the 

PTC520 employs ‘centre-post’ clamping and patented 

‘Lever / No Lever’ operation on rims up to 30” diameter. 

In addition, the integral pneumatic wheel lifter 3-way 

Assist Arm ensures minimal effort from the operator 

and complete peace of mind when handling difficult or 

prestigious rim and tyre combinations. 

• 30” rims handled via centre-post clamping 

• Choose between leverless or conventional 

operation by simple adjustment 

• Perfect for anyone handling exotic or difficult 

rims and tyres 

• Integral wheel lifter 

• 3-Way Robotic Assist Arm 


• Fully-Automatic, tilt-arm operation with 

automatic back/forth movement of the turret 

and up/away movement of the demount head 

• 10” to 24” clamping (22” external) 

• 3-way robotic assist arm provides assistance 

in all areas of fitting and removal of the tyre 

• Proven, Italian-designed electronics and 

engineering make this wheel balancer 

reliable and functional, and simple to use 

• Both machines single phase operating from a 

3-pin plug 

3D WHEEL BALANCER WITH SONAR 

AND LASER 

High-end, premium quality wheel balancer with 3D 

Automatic data input via sonar and full-colour TFT 

display. 

• Handles rims up to 30” diameter 

• 3D Automatic Data Entry via Sonar 

• 6 o’clock weight placement using Laser 

guidance 

Entry of the rim data is achieved by simply 

selecting your preferred weight position 

using the internal arm and lowering the 

hood, it is that simple! The inside of the 

rim is automatically illuminated to allow 

better visibility when placing the weights, 

which can be done at either the 12 or 6 

o’clock position. Advanced features like 

Split Weight has never been easier due to 

the live on-screen animation. 

Dingbro Ltd 


13




PWA60 

4CCD COMPUTERISED WHEEL ALIGNER 

One of the UK’s best-selling Wheel Aligners, the PWA60 comes 

with a price tag that makes it accessible to the most modest of 

garages, and yet compromises on nothing in terms of capability. 

The simple and speedy ‘hang-on’ clamps make it a logical next step for those used 

to doing laser alignment. Our new ‘F-Tab’ software gives it a familiarity to those 

who have used computerised aligners already. 

• Ingenious ‘hang-on’ clamps 

• Smart new software means less buttons to press 

• Autodata Vehicle Database 

• Compact yet highly capable 

• Bluetooth Wireless Technology 

• Unbeatable Price vs Performance ratio 

Can be used 

on 2 Post Lifts 

with optional 

accessories 

PWA60 PRO 

6CCD COMPUTERISED WHEEL ALIGNER 

Another best-seller, the PWA60 Pro offers up a specification 

that matches up to some of those ‘famous’ alignment 

systems which are literally three times the price!! 

Improving further on all of the attributes of the PWA60, the ‘Pro’ comes 

with some luxury features such as ANPR (Automatic Number Plate 

Recognition), ADAS-Ready Software and premium 3-point ‘FastClamps’. 

ANPR AS STANDARD 

£ 

6,995 

(AN ADDITIONAL COST ON MANY ALIGNERS) 

PWA-3D 

‘TOWER-FREE’ 3D COMPUTERISED ALIGNMENT SYSTEM 

Unlike traditional 3D systems, which require a great deal of space in front of the lift, 

the PWA-3D provides ingenious lift-mounted cameras, making it more accessible to 

those where space is at a premium. 

Lightweight ‘targets’ remove all of the expensive technology from the vulnerable position of being on the rim, 

meaning cost of ownership and downtime can be massively reduced versus CCD systems. Modular in it’s 

design, the PWA-3D can be configured to your specification, with a range of clamps and software options 

available, including OEM specific models for the likes of BMW and Mercedes-Benz. 

• 3D ‘Camera and Target’ Technology 

• Space-saving over traditional 3D Systems 

• Varying Clamp and Software Options 

• ANPR, ADAS-Ready, and many other features can be included or removed 

• Full on-site demonstration available unlike most 3D systems 

• Made In Italy by some of the Worlds leading alignment engineers 

NEW! 

Perfect for 

Alignment 

NO MORE 

oxy-acetylene! 

HEAT MATE 

INDUCTION HEATER 

Common workshop processes become a 

breeze including the un-seizing of bolts, 

track rod ends and ball joints. The Heat Mate 

Induction Heater from Hofmann Megaplan 

is the perfect partner to any of our premium 

wheel alignment solutions. 

Heat Mate 

Buy any Aligner + 

2 Post Lift Combi & 

SAVE £250, 

or buy any Aligner + 

4 Post Lift Combo & 

SAVE £500! 

£ 

2,595 £ 

2,795 



Heat Mate Pro 

(with portable trolley) 


£ 

4,995 


Delivered, 

Installed, Trained 

and Supported by a 

Nationwide Team of 

Dedicated Alignment 

Experts! 

• Luxury 3-Point ‘FastClamps’ 

• Software developed to specific OEM standards 

• ADAS-Ready 

• ANPR (Automatic Number Plate Recognition) 

included 

• Bluetooth Wireless Technology 

• Made in Italy by some of the world’s leading 

alignment engineers 

FROM 

£ 

9,995 


• It’s fast! Heat Mate takes seconds to 

heat ferrous based metals. 

• It’s easy to use! Plug it in, switch on 

and you’re off. 

• It’s accurate! Finger point accuracy 

allows for close proximity to heatsensitive 

parts. 

• It’s long-lasting! Water-cooled 

components mean longer usage 

times. 

• It’s safe! The flameless solution 

means no naked flame or excessive 

heat. 

• It’s cheaper! By up to 50% vs. 

oxyacetylene 

TREADSMART 2 

AUTOMATIC DRIVE-OVER TREAD DEPTH 

MEASUREMENT & TYRE HEALTH CHECK 

PVL4000 

2 POST VEHICLE LIFT 


• Can be recessed or surface-mounted. Low profile surface-mounted 

version (just 90mm) means no excavation necessary 

• Generate tyre and alignment sales through credible supporting printout 

or electronic report which can be emailed to the customer 

• Software can be integrated into Atlas Platinum alignment systems 

• Installation and training carried out by factory-trained technicians with 

ongoing diagnostic and advisory support from a nationwide team 

• ‘Zoom’ function allows you to home in on a specific tyre for more detailed 

explanation 

• Optional ‘Traffic Light System’ will indicate when the next vehicle can be 

loaded and automatically grabs the number plate and inserts the vehicle 

details straight into the database. 

£ 

2,295 

Not to be confused with ‘budget’ lifts of similar pricing, 

the PVL4000 has been designed in Europe with European 

vehicles in mind. 

Too many customers focus on lifting capacity, when actually versatility is the 

most important factor. Higher lifting capacity is purely vanity; it is irrelevant if 

you can’t accommodate the vehicle safely in the first place. This is where the 

PVL4000 scores over its competition which may boast higher lifting capacity. 

The PVL4000 incorporates 3-Stage arms all-round, ensuring that the arms 

can be retracted and extended to a far greater degree, and therefore making 

it one of the most (if not the most) versatile 2 post lifts on the market. The US 

version of this lift is categorised as ‘Super-Duty’, and we think that sums up 

the build quality of the PVL4000. 

• Lifting Capacity 4000KG 

• 50s lifting time, 60s lowering time 

• Low-profile arms 

• 3-stage arms all round 

• Automatic, electronic safety-release 

3 STAGE ARMS 

ALL ROUND FOR 

MAXIMUM VEHICLE 

COVERAGE! 


The Atlas Platinum Drive-Over Health Check Unit is the perfect 

partner to any garage or tyre shop selling tyres or alignment. 

Simply drive the vehicle over to get instant readings and advisory 

information such as tread depth, adverse tyre wear, mis-alignment and 

under/over inflation issues – all of which results in additional tyre and 

alignment sales, as well as providing undisputed data and credibility 

with your customers. The software can be integrated into any compatible 

alignment machine to avoid duplication of PC systems and printer set ups. 

PVL QUADRO 

4 POST VEHICLE LIFT 

The PVL Quadro is widely considered one of the best alignment 

lift designs on the market. 

£ 

5,995 

The alignment platforms are specifically designed with alignment in mind, unlike most other lifts 

which take a standard lift and bolt on additional platforms. The value in having a dedicated alignment 

lift, supplied by the same manufacturer as the aligner, cannot be under-estimated. With a 4200KG 

lifting capacity, the PVL Quadro is available in both 4.5m and 4.8m lengths. A reassuring 2 Year 

Warranty provides peace of mind that you are investing in a quality product. 

• 4200KG Lifting Capacity 

• ‘Made for the job’ alignment platforms consist of Front Recesses and Rear Slip Plates 

• Available in 4.5m and 4.8m platform lengths 

• Width between columns of 2850mm, making it ideal even for ‘Crucifix’ style alignment 

Buy any Aligner + 

2 Post Lift Combi & 

SAVE £250, 

or buy any Aligner + 

4 Post Lift Combo & 

SAVE £500! 

£ 

13,995 


NEW! 

Generate 

alignment 


Dingbro Ltd 


15



Tecalemit 

Tecalemit 

ATL PACKAGES 

ATL XERO PACKAGES 

The ATL Xero is for customers who want a lower cost, 

initial investment ATL package whilst maintaining the 

quality and specification of fully approved equipment. 

Each of the ATL Xero packages includes 4 post lift, 

brake tester, jacking beam, headlamp beam tester, 

mirror kit and brake applicator. Other options can 

then be added as required. 

2 POST LIFTS 

Part No. 

Lifting 

Capacity 

Raised 

Height 

Application 

SF/9010/H 3.0T 1.96m Mechanical lift 

with base frame 

SF/9207 4.0T 1.8m Hydraulic lift 


Price 

£2,999 

£3,795 

3T Mechanical Lift with Base Frame (1.96m) 

• Azur 3.0t 2 Post Lift with heavy duty base frame 

• Suitable for lifting most passenger cars and car derived vans 

• Automatic arm locking 

• 5 year warranty on self lubricating Nylatron operating and 

safety nuts 

• Low minimum lifting pad height of just 90mm 

• Foot/toe protection device 

• Ideal for transmission work 

Model 

SF/9010/H 

ONLY 

£ 

2,999 


3.2T Model 

Available 

SF/9010/H/32 

4T hydraulic lift 


Model 

SF/9207 

• Electro-hydraulic operation 4.0t 2 Post Lift 

• Asymmetric lifting arms 3 stages 

for lifting a wide range of vehicles 

• Rapid lifting time 

• Structural base frame 

• Electronically controlled safety latches 

• 3PH power supply 

• Includes free high lift pads 

1PH Model 

available 

FROM 

£ 

3,795 


ATL 5 STAR PREMIUM 

PACKAGES 

WITH ENHANCED SERVICE SUPPORT OVER 5 YEARS 

Extras over standard ATL packages: 

• Checker plate finish on lift platforms 

• Large cabinet workstation 

• Floor lift strike plates 

• Full brake tester installation cassette 

• Premium headlamp beam tester with laser 

• Air Operated Jacking Beam 

• 5 year calibration, service & repair package 

Terms & Conditions 

1. For new orders only 

2. Customers name must be supplied at point of order 

3. The order for the ATL bay, and the accompanying product must be ordered at the same time 

4. ATL Bay must be despatched within 6 months of the order date 

5. Emissions tester and 3 Year Tecalemit prepaid service contract must 

be purchased at the time of order. 

6. Excludes pit packages and ATL Xero packages. 

7. 1,2,3,4 offer products cannot be used in combination with other offers for those products 

8. 1,2,3,4 offer is only available to the ATL purchasing customer. 

ATL Xero 

PACKAGES 

START FROM 

JUST 

£ 

16,749 

1, 2, 3, 4 TECALEMIT 

OFFERS YOU MORE 

FREE VALUE ADD OPTIONS 

ON TECALEMIT BRAND AND 

AUTOMATED TEST LANES** 

Purchase a qualifying ATL Class IV or VII package with 

a 3 Year Tecalemit prepaid service contract to receive a 

3 Year Warranty and choose one of the four Value Add 

options FREE 

Select One of Four Value Add Options from the “1, 2, 3, 4 Tecalemit Offers You More” promotion* 

* **For all qualifying ATL packages ordered in the promotional period, Tecalemit will include one of either: 

1, 2, 3, or 4. NOT available on ATL Xero packages or ATL Pit packages 

1 2 3 

4 

SAVE £1,000 OR SAVE £1,250 OR OR 

ON ANY 2 POST LIFT 

SAVE 

£1,000 

ON ANY 

2 POST LIFT 

ORDER ANY 

TECALEMIT 2 POST LIFT 

AND CLAIM £1,000 

OFF THE PRICE 

ON ANY 4 POST LIFT 

SAVE 

£1,200 

ON ANY 

4 POST LIFT 

ORDER ANOTHER 

TECALEMIT 4 POST LIFT 

AND RECEIVE £1,250 OFF 

THE PRICE 

GTR/400/W 

FREE 

OR 

£1,000 

OFF ANY 

TECALEMIT 

WHEEL 

ALIGNMENT 

SYSTEM 

CLAIM A FREE 

GTR/400/W OR ENJOY 

£1,000 OFF ONE OF OUR 

OTHER WHEEL ALIGNERS 

SF/9207 

FREE 

4.0T 

2 POST 

LIFT 

CLAIM A FREE SF/9207 

AND ADD THIS VERSATILE, 

PROVEN 4.0T 2 POST LIFT 

TO YOUR WORKSHOP 

4 POST LIFTS 

Part No. Lifting Capacity Platform Length Application Price 

SF/9436/SR 3.5T 4.3m Servicing & Class IV MOT* £5,950 

SF/9084 4.0T 5.0m Service Lift £6,250 

3.5T Service Lift 

• Maximum Load: 3500kg 

• Raised Platform Height:1700mm 

• Lifting Time: 50 sec 

• Lowering Time: 45 sec 

• Minimum Height: 120mm 

• 3ph or 1ph options available 

• 4.3m Platform 

ONLY 

£ 

5,950 


Model 

SF/9436/SR 

SCISSOR LIFTS 

• Raised height: 1900mm 

• Motor supply: 400 3kW - 3Ph 50Hz 

• Maximum load: 4000kg 

• Lifting/Lowering time: 35 secs 

• Operation: Electro-hydraulic 

• Extendable platforms 


Model 

SF/8994 

Single Phase 

Options 

Part No. Lifting Capacity Lifting Height Application Price 

SF/8992 3.2t 1.9m Short platform, 

low profile 

SF/8994 4.0t 1.9m Short platform, 

recessed 

4T In-ground Scissor Lift 

ONLY 

£ 

5,595 


£4,995 

£5,595 

* Requires radius 

turning plates 

for M.O.T. 

Single Phase 

Options 

* Requires 

radius turning 

plates for M.O.T. 

4T Service Lift 

• Lifting Capacity: 4000kg 

• Lifting/Lowering Time (3ph): 35 sec 

• Lifting Height: 1830mm 

Model 

SF/8992 

5T 

5.2m Model 

Available 

Model 

SF/9084 

SF/9250 

• Minimum Height: 165mm 


• 5m Platform 

Single 

Phase Model 

Available 

SF/8992/1 

ONLY 

£ 

6,250 


3.2T Scissor Lift 

• Operation: Electro-hydraulic 

• Capacity: 3200kg 

• Lifting height: 1945mm 


ONLY 

£ 

4,995 


Dingbro Ltd 


17



Tecalemit 

Tecalemit 

TYRE CHANGER & WHEEL BALANCER 

PACKS 

Tyre Changer TTC/TIRO/1 

• Automatic tyre changer 

• Rim diameter 11” to 24” 

• Air operated tilting column for 

car, motorcycle and commercial 

wheels 

• Comes with 3 Assistant Arms Inc 

pressing/lifting tool for use with 

on Low-profile, UHP and Run-Flat 

tryes 

• 230v Single Phase 

Tyre Changer TTC/9620/T 

• Automatic tyre changer 

• Outside rim clamping 10“/22 “ 

• Inside rim clamping 12“/24” 

• Rim width 3“/11“ 

• Max. wheel diameter. 1100mm 

• Bead breaker range.65mm/305mm 

• Air connection 8-10 bar 

• Twin Speed of rotation.7-15 rpm 


• Model With Optional Technoroller = 

TTC/9620/T (Shown) 

MADE IN 

ITALY 

TYRE CHANGER TTC/9624S/T 

• Automatic Tyre Changer 

• Outside rim clamping 10“/24“ 

• Inside rim clamping 12“/28“ 

• Rim width 3“/12.5“ 

• Max. wheel 1200mm 


• Air connection..8-10 bar 

• Inverter Variable speed controlled 


MADE IN 

ITALY 

Tyre Changer TTC/9628S/T 

• Automatic Tyre Changer 

• Outside rim clamping 12” - 28” 

• Inside rim clamping 13” - 32” 

• Rim width 3” - 15” 

• Max. wheel 1200mm 


• Air connection..8-10 bar 

• Inverter Variable speed controlled 


• Leverless option available 

MADE IN 

ITALY 

TECALEMIT TIRO PACK 

TTC/TIRO/1-TBM/TIRO/2500 

Wheel Balancer TBM/TIRO/2500 

• 4 Alu and 1 Steel programmes 

• Rim width 1.5” - 20” 

• Rim diameter 10” - 24” 

• Balancing speed 200 rpm 

• Max. wheel weight 65kg 

• 230V Single phase 50Hz 

FROM ONLY 

£ 

2,999 


TECALEMIT PROFESSIONAL PACK 

TTC/9620/T-TBM/960A 

Upgrade to TTC/9628S/T to get 28” 

External Wheel Clamping 

Wheel Balancer TBM/960A 

• Semi Automatic, Max Wheel Diameter 31.5” 

• Rim Diameter 8” – 26.5” 

• Wheel Weight 65Kg 

• Internal Data Entry Arm 

• Led Display, 240v Single Phase 

TECALEMIT EXPERT PLUS PACK 

TTC/9624S/T-TBM/960AE 

Upgrade to TTC/9628S/T to get 28” 

External Wheel Clamping 

Wheel Balancer TBM/960AE 

• Semi Automatic 

• Max Wheel Diameter 31.5” 

• Rim Diameter 8” – 26.5” 



• External Data Entry Arm 

• Led Display, 240v Single Phase 

TECALEMIT MASTER 28 PACK 

TTC/9628S/T -TBM/9165L/AE 

Upgrade to TTC/9628S/LL/T to get 

Leverless Tyre Removal 

FREE STARTER 

PACK 

PARTS ALLIANCE 

EXCLUSIVE 

FROM ONLY 

£ 

5,699 


FROM ONLY 

£ 

6,395 


Wheel Balancer TBM/9165L/AE 

• Fully Automatic 

• Laser line for precise weight positioning 

• Powerful internal LED light 

• Max Wheel Diameter 47.5” 

• Rim Diameter 10” - 26” 



• External Data Entry Arm 

• Dual LED Display 


FROM ONLY 

£ 

7,595 


GTR/400/W 

GTR/400/W 

• Highly accurate and easy to use 

• Suitable for car wheel rim sizes 

up to 23” 

• Compact wall mounted storage of 

equipment 

• On-rack recharging of lasers 

• Includes pedal applicator and 

steering wheel clamp 

• Measures front & rear toe, total 

toe, set-back and rear axle thrust 

line 

Buy the GTR/400/W 

& Camber Caster 

together for just 

Optional camber caster 

(LA/CTD) available 

User install, training DVD provided 

GTR/3020 

Model 

GTR/3020 

Compact easy to use high precision 

4 wheel laser alignment system. 

Upgrade to 

an XL Kit 

for larger 

wheels 

£ 

2,095 


£ 

465 

GTR/400/W 

FROM ONLY 

KIT INCLUDES 

Longer Rear Flags, 

Set 6 Rime Extension buttons 

Pair Head Extensions 

Extended Head Hangers 

(£189 Parts Alliance Exclusive) 

Full 4 Wheel Alignment Wireless 

8CCD Camera System 

GTR/3020 

£ 

1,895 


BARGAIN! 

• Quick & easy measurements in a few 

minutes 

• 8 CCD electronic measuring heads 

• Bluetooth cable free communication 

• PC controlled/windows operating system 

• Precision measurement of angles 

• Haweka Pro-clamp wheel mounting 

system, no run out compensation needed 

• Extensive vehicle database 

• Colour before/after printout 

• Camera tilt facility 

overcomes low spoilers 

• The unit has freeze frame 

facility to use on 2 Post Lifts 

GTR/3020 

FROM ONLY 

£ 

7,750 


CALL FOR 

A DEMO 

GTR/430 

GTR/430 

• Developed by Tecalemit to provide rapid 

measurement of key vehicle geometry 

angles 

• Compact and easy to use high 

precision 4 wheel laser aligner 

• Autodata database with red/green display of 

results when in/out of parameter 

• Includes a brake pedal depressor, 

steering wheel clamp and radius plates 

• Zigbee wireless PC interface which allows 

for measurement results to be printed and 

archived on to the supplied PC 

• 2x built-in camber caster gauges 

• Stylish new cabinet on wheels houses the 

PC and printer 

Upgrade to 

an XL Kit 

for larger 

wheels 

GTR/430 

FROM ONLY 

£ 

4,495 


GTR/8400 

4 Wheel Laser Alignment with 

Vehicle Database and Live Data 

KIT INCLUDES 

Longer Rear Flags, 

Set 6 Rime Extension buttons 

Pair Head Extensions 

Extended Head Hangers 

(£189 Parts Alliance Exclusive) 

New 3D Computerised 4 Camera 

Wheel Alignment System 

GTR/8400 

• 4 HD digital video cameras enable rapid target capture 

at any ramp height eliminating the need for a movable 

boom 

• Utilising 4 cameras enables cameras to be positioned 

closer to the ramp than is possible with 2 camera 

systems 

• The 4 wide angle cameras provide up to twice the range 

of working heights compared with 2 camera systems 

• Unique “Machine Vision” 

software provides accurate 

measurements without the need 

to calibrate targets 

• Integrated database incorporates 

alignment specifications, 

adjustment diagrams and 3D 

animated instruction videos 

• Self centering wheel adapters 

accommodate wheel sizes 

12” – 24” 

• Integrated storage for adapters 

and targets on the cabinet 

• Cabinet comes with high 

specification fast PC, extra wide 

27” monitor, printer, and unique 

wireless remote control 

GTR/8400 

FROM ONLY 

£ 

8,895 


Dingbro Ltd 


19



Denso 

Denso 

KRISTAL BASE 

R1234YF FULLY Automatic 

Air Con Service Station 

PART NO: CE92009KB 

Machine Components 

• 10 Litre Cylinder Capacity 

• 1 Electronic Scales for Gas 

• Automatic Oil/UV Dye Injection 

• Comprehensive Vehicle Database 

• Self Service Replacement Filters 

• 2.5m Charging Line with Couplings 

• Refrigerant Tank Lock 

Includes: 

• Free F Gas Training for One Person 

• Free Delivery & Commissioning 

• Free Technical Helpline 

ANTI BAC 

TREATMENT 

MACHINE 

PART NO: GEQ261AA0870 / 261AA0870 

NORMALLY: 

£ 

199 

STARTER PACK 

Get the Anti Bac 

Ozone Purifier for 

ONLY £99 

with any Air Con 

Machine Package 

SAVING £100 

off the trade price 

Mainboard / Database 

Automotive / Commercial Vehicles 

Re-Order Notification for Oil / Dye 

Thermal Printer 

Personalised Document Printout 

Report Reprints Available 

GUARANTEE 

3 YEAR 

SATISFACTION 

Terms and Conditions 

apply. 

The machine must be 

serviced after 

Year 1 and Year 2. 

KHEOS PLUS 

R134A FULLY Automatic 

Air Con Service Station 

PART NO: CE92006KP 

Machine Components 

• Fully Programmable 

• Comprehensive Vehicle Database 

• 10 KG Refrigerant Cylinder 

• Easy Read Pressure Gauges 

• Automatic Recovery / Vacuum/ Charge 

• Automatic Oil Discharge 

• 100 L/ Min Vacuum Pump 

• 400 G per Min Recovery Pump 

• Counters for Machine Servicing 

• Heater Blanket 

Includes: 

• Free F Gas Training for One Person 

• Free Delivery & Commissioning 

• Free Technical Helpline 

AIR CON PROFIT 

OPPORTUNITY! 

Purchasing a Kheos Plus (R134A) 

Air Conditioning service station will 

not only give you control & flexibility 

in your workshop but it will offer 

high profit margins on all your air 

conditioning service repairs. 

A fully automatic service station, 

accessory packs, consumables with 

training can be purchased & the full 

cost recovered within the first 

6 months of use! 

Carry out just 2 air con recharges pw 

@ £ 69 each = £ 138 

Material cost to carry out 2 air con recharges pw 

@ £ 16.80 each = – £ 33.60 

Increasing your profit by £ 104.40 pw 

The cost of your equipment package will be 

recovered within just 20 weeks 

EXAMPLE OVER ONE YEAR 

2 air con recharges @ £ 69 each pw 

over 12 months = £ 7,176 

Material cost to carry out 2 air con recharges 

@ £ 16.80 each pw 

over 12 months = – £ 1,747 

PART NO: CEACC3K 

SPECIAL PRICE: 

£ 

599 

DIAGNOSTIC PACK 


GUARANTEE 

3 YEAR 

SATISFACTION 

Terms and Conditions apply. 

The machine must be serviced after Year 1 and Year 2. 

Recovery Pump 

High Speed Recovery 

400g per minute 

Vacuum Pump 

DIAGNOSTIC PACK 



£ 

140 

STARTER PACK 



£ 

170 

FULL YEAR PROFIT OF £ 5428 

LESS COST OF EQUIPMENT £ 1895 

NETT PROFIT IN FIRST YEAR £ 3533 

OR 

Carry out just 2 air con recharges pw 

@ £ 69 each = £ 138 

Carry out just 1 condenser change pw @ £ 250 

Material cost to carry out service & repair work pw 

@ £ 200 

Increasing your profit by £ 188 pw 


£ 

170 

MACHINE 

ONLY PRICE FROM: 

£ 

2,275 

Weekly from: £ 12.08 

2 Stage Pump High Capacity 

170 Litre / min 

COMPLETE 

PACKAGE PRICE FROM: 

£ 

2,995 


MACHINE 

ONLY PRICE FROM: 

£ 

1,795 


COMPLETE 

PACKAGE PRICE FROM: 

£ 

1,975 


EXAMPLE OVER ONE YEAR 

1 air con recharge @ £ 69 each pw & 1 condenser 

change @ £ 250 each pw 

over 12 months = £ 20,176 

Material cost to carry out service work 

over 12 months = – £ 10,400 

FULL YEAR PROFIT OF £ 9,766 

LESS COST OF EQUIPMENT £ 1,895 

NETT PROFIT IN FIRST YEAR £ 7,881 

Dingbro Ltd 


21



Denso 

GYS 

MRL 85 UNIVERSAL OIL 

A ONE STOP SOLUTION 

FOR OIL AND DYE! 

This NEW lubricant has been specially formulated to work in all types 

of vehicle air conditioning systems. A synthetic ester blend oil being 

non - conductible and is therefore safe to lubricate the hybrid car air 

conditioning system. Service stations can now use one oil instead of 

flushing charge lines, changing oil and dye bottles and carrying four if 

not more different system oils in stock. Therefore using the MRL-85 Oil 

becomes a sensible option and more cost effective. 

• Synthetic ester blend 

• Non conductible 

• Cost effective 

• Hybrid & Electric safe 

• HFO1234YF 

• R134A 

MRL 85 OIL 

Special Price: £ per Ltr 

19.99 

PART NO: CE98029ML / 261AA0630 

MRL 85 OIL/UV DYE MIX 

Special Price: £ per Ltr 

22.99 

PART NO: CE91067ML / 261AA0620 

A NEWLY FORMULATED OIL TO USE IN ‘ALL’ 

VEHICLE AIR CONDITIONING SYSTEMS 

CONSUMABLES 

INCLUDES FREE 

'SOAPY SUDS' 

LEAK DETECTOR 

£ 

135 

Nitrogen Pressure Testing Kit 

PART NO: CE93027 / 261AA0740 

£ 

279 

All Prices 

Excl VAT 

Anti Bac Treatment Machine 

PART NO: CE98045B / 261AA0840 

£ 

199 

Anti Bac Ozone Generator 

PART NO: GEQ261AA0870 / 261AA0870 

£ 

30 

Leak Stop 

NEW 

PART NO: CE92555 / 261AA0650 

F GAS 

LICENCESING 

FROM 1 ST JANUARY 2015 A NEW 

EU DIRECTIVE NO: 

517/2015 F GAS REGULATION 2 

Approved Centre 

SAFE HANDLING 

OF REFRIGERANTS 

CERTIFICATION 

CITY & GUILDS 7543 - 01 

This Certification meets the above EU 

Directive. On Site Training and Assessment 

throughout the UK 

ASSESSMENTS FROM: 

£ 

220+VAT 

(Per Technician - Discounts available 

for Multiple Assessments) 

£ 

24 

Renault Charge Port 

PART NO: CE93054A / 261AA0690 

025677 NEW PRODUCT GYSFLASH 123.12 

Battery Support Unit 

PART NO: 25677 

• Carrying handle & rubber 

boot for increased portability 

& floor standing use 

• Option to wall mount or 

attach to vehicle lift post 

• 120Amp current supplied on 

demand 

• DIAG+ mode – user adjustable 

voltage 12-14.8v (in 0.1v 

increments) 

U56992 POWERDUCTION 37 

HEAT INDUCTION MACHINE 

PART NO: U56992 

• Provides instant, safe, flameless heat 

• No damage to surrounding components 

• Powerful 3700Watts – heats M10 bolt 

in 1 sec 

• Ideal for releasing seized track rod 

ends, manifold studs, exhaust 

brackets etc 

• List Price £2,718.80 


£ 

1,999 


• Charger mode – charges all battery types including 

EFB & AGM stop/start + Lithium 

• Safe to charge without disconnecting battery 

• Connected Technology - future software updates 

• List Price £949.00 

downloadable, extract charging data via USB, 


connection to Wi-Fi, printer, scanner etc. 

• Supplied with 5m cables 

£ 

889 

025592 DIAG-STARTIUM 

60.24 3 IN 1 Smart Starter/ 

Smart Charger/ Battery 

Supoort Unit 


• The only SMART starter that passes the 

GYS 123 Test 

• Safety – protection for vehiclew elctronics 

• All Battery types – Lead acid, gel, silver/ 

calcium, EFB & AGM stop/start 

• Universal Mode – Safe to use when battery 

type unknown. 

• Provides 60Amps battery support 

• Suitable for safe smart starting of cars, 

vans & LCV’s 



£ 

649 

£ 

24 

Ford Extension Port 

PART NO: CE90345 / 261AA0680 

£ 

32 

O Ring Kit 

PART NO: CE54019 / 261AA0660 

£ 

50 

Valve Cap Kit 

PART NO: CE51997 / 261AA0670 

£ 

7 

Gas Bottle Adaptor 

PART NO: CE93034 / 261AA0700 

£ 

30 

R1234YF Gas Bottle Adaptor 

PART NO: CE93034YFH / 261AA0710 

027879 Gyspack 660 12v 

Booster Pack 


• Suitable for starting cars & vans 

• On/Off switch to prevent misuse 

• Reverse polarity alarm 

• Internal battery tester 

• LED worklamp 

• Automatic charger enables booster to 

be left permanently connected to mains 

ensuring always fully charged. 


024229 Battery Tester with Printer 


• Features latest dynamic resistance testing 

technology (minimises battery discharge) 

• Provides instant test results with print out 

• Tests battery voltage & battery health (12v) 

• Test alternator no load & charging voltage & 

ripple (12v & 24v) 

• Tests starter motor output (12v & 24v) 

• Can test all battery types including EFB & 

AGM stop/start (up to 230Ah) 


CTR Astra Oil / UV Dye 

£ 

12 

£ 

16 

PART NO: CE98029MLCTR 250ML / 261AA0630 

PART NO: CE91067MLCTR 125ML / 261AA0620 

CTR Oil / UV Dye Mix 

£ 

15 

PART NO:CE91067BCTR 250ML / 261AA0610 

UV Dye 

£ 

30 

£ 

85 

PART NO:CE91067H 250ML / 261AA0640 

PART NO: CE91067I 1L / 261AA0770 

£ 

29 

UV Torch & Goggles 

PART NO: CE91072H / 261AA0730 


£ 

249 


£ 

199 

Dingbro Ltd 


23



SIP Pressure Washers 

DeWALT 

SIP CW2800 

ELECTRIC PRESSURE WASHER 

• 230v (13A) input supply 

• 2800w brushless induction motor 

• 2610psi (180bar) max. pressure 

• 510litres/hour max. water flow 

• Steel adjustable lance 

• Steel Turbo lance 

• Reliable heavy-duty Axial pump 

• Total stop - stops power when 

not in use 

• 8 metre hose with integrated 

hose reel 

• 1.8 litre detergent tank 

• Wheel-mounted 


ONLY 

£ 

249 

INTEGRATED 

DETERGENT 

TANK 

ITALIAN 

DESIGN 

SIP CW4000 PRO PLUS 



• 2800w 4-pole 1450rpm induction motor 

• 1885 to 2175psi variable pressure range 

• 540 litres/hour maximum water flow rate 

• Durable steel lance with adjustable nozzle 

• Fitted with an adjustable pressure regulator 

• Reliable brass-head Triplex crankshaft pump 

• Total stop - stops power when not in use 


ONLY 

£ 

599 

BRASS-HEAD 

TRIPLEX 

CRANKSHAFT 

PUMP 

2800W 

4-POLE 

INDUCTION 

MOTOR 

ITALIAN 

DESIGN 

SPECIAL OFFERS 

AVAILABLE NOW! 

DXV15T WET & DRY 

VACUUM CLEANER 

• Compact ‘Toolbox’ design 

• Rugged quality plastic casing 

• Integrated tool storage 

• Automatic ball-cock air shut-off 

• Blower feature for removing dust & debris 

• Lightweight and portable 

• Powerful suction/blower motor 

• Hose & accessories 

supplied 

DXV20P PROFESSIONAL 

WET & DRY 


• Rugged quality plastic casing 

• Hard-wearing castors 

• Durable side catches 

• Large sturdy On/OFF switch 





• Hose & accessories supplied 

DXV20S PROFESSIONAL 

WET & DRY 


• Stainless steel quality casing 

• Hard wearing castors 







• Hose & accessories supplied 

SIP PH600/140 T4 HOT WATER 



• Electric-powered pressure washer 

• 2200w 1400rpm 4-pole motor 

• 2030psi (140bar) max. pressure 

• 600 litres/hour maximum water flow rate 

• 100°C boiler-fired hot water temperature 

• 15 litre diesel fuel tank capacity for heater 

• 10 metre heavy-duty hose w/ rugged lance 

• Brass-headed in-line Triplex crankshaft pump 

• One-piece body cover and folding handles 

• Mounted on rear wheels and front castor 

• Low pressure detergent suction 

• Reliable boiler safety features 


ONLY 

2200W 4-POLE 

INDUCTION MOTOR 

£ 

1,479 


MADE IN 

ITALY 

SIP PH/HDS HOT STEAM 

ELECTRIC PRESSURE WASHERS 


SIP PH660/120HDS HOT STEAM 



• 2200w 4-pole brushless induction motor 

• 1740psi (120bar) variable max. pressure 

• 660litres/hr variable max. water flow rate 

• 85 - 140°C max. water temperature 

• Brass-headed, in-line Triplex crankshaft pump 

• Integral water softener and de-scaling tank 

• 3.5 litres / low pressure detergent suction 

• 10 metre heavy-duty hose included 

• Built-in pressure gauge 

BRASS-HEAD 

TRIPLEX 

CRANKSHAFT 

PUMP 

TWO YEAR 

WARRANTY 

PUMP INCLUDED 

400v - 3 PHASE 

OPTION 


SIP PH900/200HDS HOT STEAM 


• 400v, 3 phase input supply 

• 5500w 4-pole brushless induction motor 

• 2900psi (200bar) variable max. pressure 

• 900litres/hr variable max. water flow rate 

• 85 - 140°C max. water temperature 

• Brass-headed, in-line Triplex crankshaft pump 

• Integral water softener and descaling tank 

• 3.5 litres / low pressure detergent suction 

• 10 metre heavy-duty hose included 

• Built-in pressure gauge 

SIP PH720/100 HOT WATER 



• Electric-powered pressure washer 

• 3000w 1400rpm 4-pole motor 

• 1450psi (100bar) maximum pressure 

• 720litres/hour max. water flow rate 

• 100°C boiler-fired hot water temperature 

• 18L diesel boiler capacity / 3.5L detergent 

• 10 metre hose w/ rugged bent pistol lance 

• Ultra heavy-duty brass-head Triplex pump 

• Built-in water softener and descaling tank 

• Total Stop - power stops when not used 

• 2 castors and 2 wheels for movement 

• Durable integral 

ceramic pistons 


ONLY 

£ 

2,059 


x4 WHEEL 

STABILITY 

3000W 4-POLE 

INDUCTION MOTOR 

BRASS-HEAD TRIPLEX 

CRANKSHAFT PUMP 

4-POLE 

INDUCTION 

MOTOR 

TWO YEAR 

WARRANTY 

MADE IN 

ITALY 

PUMP INCLUDED 

TWO YEAR 

WARRANTY 

BRASS-HEAD 

TRIPLEX 

CRANKSHAFT 

PUMP 

STEAM 

15 

LITRE 

1100 

W 

48 MM 

HOSE 

DIAMETER 

3YR 

WARRANTY 


ONLY 

£ 

100 

DXV30SA PROFESSIONAL WET & DRY 


• Stainless steel quality casing 

• Hard-wearing castors 



• Automatic ball-cock air 

shut-off 

• Blower feature for removing 

dust & debris 


• Powerful suction/blower 

motor 

• Hose and accessories 

supplied 

30 

LITRE 

1050 

W 

48 MM 

HOSE 

DIAMETER 

20 

LITRE 

1050 

W 

48 MM 

HOSE 

DIAMETER 

3YR 

WARRANTY 


ONLY 

£ 

90 

20 

LITRE 

1050 

W 

48 MM 

HOSE 

DIAMETER 

3YR 

WARRANTY 


ONLY 

£ 

100 

DXAM2250 

CENTRIFUGAL AIR MOVER 

• 3 speed settings - Low / Medium / High 

• 3 blowing positions - Horizontal / 45º / 90º 

• Versatile for drying wet floors, shampooed carpets, 

plastered walls and ceilings etc. 

• Easy positioning - direct the airflow 

where it is needed 

• Portable with ergonomic 

handle and front 

safety grill 

130 

W 

236 

LTR/S 

500 

CFM 

AIR FLOW 


SIP PH660/120HDS 

HOT STEAM - 230v 

ONLY £ 2,159 


SIP PH900/200HDS 

HOT STEAM - 400v 

ONLY £ 2,259 


PUMP INCLUDED 

x4 WHEEL 

STABILITY 

MADE IN 

ITALY 


ONLY 

£ 

110 


ONLY 

£ 

80 

3YR 

WARRANTY 

SIP is a distributor for DeWALT Wet/Dry Vacuums and Industrial Air products 

Online Customer Service Centre at: www.2helpU.com 

Dingbro Ltd 


25



Crypton 

Crypton 

MARKET LEADING 

EMISSIONS TESTER 

AUTOMATED TEST LANES 

FOR M.O.T. TESTING 

NEW DUAL REVENUE 

OPTIMISE SPACE & GENERATE MORE 

REVENUE WITH WHEEL ALIGNMENT. 

CALL NOW FOR DETAILS 

23" Screen, Windows PC & 

Printer 

Battery Tachometer 

Gas Analyser 

AVAILABLE UP TO 6.5M! 

NEW 

OPTIONAL 40” Screen 

(photo for illustrative purposes only) 

Operates the brake tester 

Latest spec from DVSA 

Automatic calibration on 

smokehead 

Wheel Play Detectores with Torch 

Turntables 

NEW 

x2 Convex Mirrors 

Laser Aimed Headlight Aligner 

NEW 

Jacking Beam with 

OPTIONAL3.2T for 5T Lifts 

Attractive Checker Plate Surface 

Brake Pedal Depressor 

Control Center with PC & 23” Screen 

(Accommodates emissions tester) 

FREE MOT Banner 

Automated Brake Tester with 

OPTIONAL Adapter Kits for 

Motorbikes & 4x4’s 

QUALITY MOBILE CABINET 

BUILT FOR THE 

GARAGE ENVIRONMENT 

MANUFACTURED 

& SUPPORTED 

IN THE UK 

FEATURES & BENEFITS 

• DVSA approved 

• Tests classes 3, 4, 5 & 7 

• Automatic calibration on smokehead 

• First 6 months of calibrations included 

• Gas analyser is accurate to 

OIML Class O 

• Oil temperature probe 

• Multi-functional - operates our 

automated brake tester when purchased 

with an ATL Bay 

• Mouse & keyboard with dust/grease 

protective lid 

• Next day delivery (T&Cs apply)rranty 

WHY NOT UPGRADE 

TO 5 YEARS EXTENDED 

CARE? 

• 5 years warranty on all major 

components (T&Cs apply) 

• Calibrations 

• Routine consumables (at time of 

calibration) 

• DVSA MOT database updates 

We’ll make all the arrangements, 

for a hassle free service. 

Other service packages available 

EXTENDED 

CARE Weekly PACKAGE from: £16.98 † 

CABLED WIRELESS 

£ 

4,250 £4,850 

£ 

3,199 

Weekly from: £22.56 † 



CONNECTED 

EQUIPMENT 

COMPLIMENTARY CONSULTATION, 

MEASURING & PROFESSIONAL CAD 

DRAWING SERVICE FOR YOUR DVSA 

APPLICATION 

BIG QUALITY FROM THE BIG NAME 

• Choose between a 4-Post lift, scissor lift or pit lane 

• Recessed or surface-mounted lift options 

• Suitable for testing class 4 and class 7 vehicles up to 5.0 

tonnes (including motorhomes on 4-post lifts) 

• All of the accessories (as highlighted above) 

• Brake tester DVSA approved as “Connected Equipment” 

• Quality and attractive, anti-slip checker plate surface for 

maximum protection against corrosion (lifts only) 

• Free delivery and installation 

• First 6 months of calibrations included for brake tester, 

emissions and headlight aligner 

• 3 years manufacturer’s warranty (no hidden T&Cs) 

• Founding member of the GEA to ensure the highest safety 

standards and legislation requirements are met by DVSA 

WHY NOT UPGRADE 

TO 5 YEARS EXTENDED CARE? 

Available with Crypton’s Emmisions Tester (CCP800) 

for complete peace of mind. Other service contracts 

available (see opposite) 

Dingbro Ltd 


27



VDO 

VCDS Vag-Com 

EVERYDAY WORKSHOP TOOLS WITHOUT 

BREAKING THE BANK OR BLOWING YOUR MIND 

® 

VCDS HEX-V2 

INTERFACE 

HEX-V2: The new generation 

VCDS ® interface 

Official licensed VCDS HEX-V2 interface & USB cable 

Serious car diagnostics interfaces for Volkswagen, Audi, Seat & Skoda models 

FOR ALL 

VAG GROUP 

MODELS 

More than a Simple Service Tool 

• Dealer level software - procedures included 

• Automatic vehicle/ECU communication through VIN 

• Unbelievably easy to use for any skill level 

• Electronic handbrake functions 

(EPB) on 20+ manufacturers 

• DPF regeneration 

• Injector coding 

• Service light reset (including Vauxhall 

where security code is required - we extract it! 

• Steering angle calibration 

• Battery replacement configuration 

on stop/start vehicles 

• Passenger vehicle and light commercials 

covered, including Iveco 

• Regular updates online 

Autodiagnos Check 

£ 

595 

LIFETIME 

WARRANTY 

(when subscription 

is upheld) 

The Ross-Tech VCDS ® package (previously known as VAG-COM) turns your PC into a sophisticated VAG diagnostic 

tool, that performs the functions of a factory VAG scan tool. The new generation wired VCDS has been designed to 

replace the HEX-USB+CAN and Micro-CAN products. 

• Includes Official Ross-Tech ® HEX-V2 interface and USB cable 

Fully licensed for VCDS ® Software, no additional software purchase needed 

• Professional user level interface - unlimited VINs 

• Fully licensed with Ross-Tech ® , Fast scans 

• User replaceable USB cable 

• Resets Service and Inspection Reminders even on 2018 models. 

• Compatible with Windows PCs and Laptop running Windows 7, 8 and 10 

Ross-Tech ® VCDS ® with HEX-V2 works on all diagnostic capable systems on: 

• VW cars and light vans to current 2018 models (not Crafter van*) 

• SEAT cars and light vans to current 2018 models 

• SKODA cars and light vans to current 2018 models 

• Audi cars to current 2018 models 

• Note, very early car models (mostly pre 1998) with the 2 pin connectors, 

or LT vans with a round connector need an additional adapter 

*Coverage for Crafter van will be added in a future update 

INTERFACE ONLY 

ONLY 

£ 

395 

FOR ALL 

VAG GROUP 

MODELS 

HEX-V2 

(INTERFACE ONLY) 


THE NEW VCDS 

INTERFACE’S 

ARE NOW THREE 

TIMES FASTER!! 

HEX-V2 PROKIT 

Part No: 989AA0011 

ONLY 

£ 

475 

NEW 

TPMS tools perfectly adapted to the needs 

of technicians 

Tyre Tread Gauge 

£ 

186 

VDO TPMS Go 

£ 

267 

2 YEARS 

SOFTWARE 

UPDATES 

VDO TPMS Pro 

£ 

699 

VDO TPMS Pro Print 

£ 

799 

Functionality Go Pro 

Easy Make-Model look-up • • 

Worldwide vehicle coverage, always up-to-date • • 

Activates all OEM sensors, displays all sensor data • • 

Program universal sensors (configurable, hybrid, ID copy etc) • • 

Provides TPMS relearn procedures in +22 languages (incl. indirect/direct) • • 

Indicates OE sensor and service kit part numbers • • 

Programs sensors from historical data 

• 

Programs sensors by wheel set 

• 

Includes OBDII routines to reset the ECU in



TEXA 

TEXA 

2 YEAR CAR DOIP 

PACKAGE DEAL 

PACKAGE INCLUDES: 

• AXONE NEMO including IDC5 

premium car and supercar 

software 

• Navigator TXTS 

• DOIP module 

• TPS 

• AXONE NEMO stand 

705R 134A 

705R 134a 

CODE: UKA6001 

705R FOR 134a 

PRINTER 

£ 

1,675 


705R 134a 

WITH START UP PACK 

CODE: UKA6002 

705R FOR 134a 

PRINTER 

6KG 134a REFRIGERANT 

SAFETY GLOVES 

SAFETY GOGGLES 

PAPER ROLLS X5 

£ 

1,950 


705R SEMI AUTOMATIC 

SERVICE STATION FOR 134a 

10KG INTERNAL TANK SINGLE STAGE 

VACUUM PUMP VEHICLE 

DATABASE ON SD CARD 

*All contracts and warranty will be 

initiated in line with the tool activation 

date 

OFFER 1 

707R 1234YF 

707R 1234yf 

707R 1234yf 


707R 1234yf 

RID START UP PACK 

CODE: UKA6011 CODE: UKA6012 CODE: UKA6013 

707R FOR 1234yf 707R FOR 1234yf 707R FOR 1234yf 

PRINTER PRINTER PRINTER 

5KG 1234yf REFRIGERANT 

SAFETY GLOVES 


REFRIGERANT IDENTIFIER 


SAFETY GLOVES 

707R FULLY-AUTOMATIC 

SERVICE STATION FOR 1234yf 10KG 

INTERNALTANK, SINGLE STAGE 

VACUUM PUMP, SCALE LOCK & 

VEHICLE DATABASE ON SD CARD 



CODE: UKD2497 

• 12 Months car & TPS software updates 

• 12 Months car & TPS technical support 

• 2 Years warranty 

CODE: UKD2487 

• 36 Months car & TPS software updates 

£ 

4,650 • 36 Months car & TPS technical support £ 

5,750 



£ 

1,995 


712R 1234YF 

£ 

2,600 



£ 

3,400 


*FOR 1234yf THE USE OF MANUFACTURER 

SPECIFIC OIL IS RECOMMENDED 

AXONE 5 CAR/LCV 

(NANO S VCI) 

712R 1234yf 

712R 1234yf 


712R 1234yf 

RID START UP PACK 


712R FOR 1234yf 712R FOR 1234yf 712R FOR 1234yf 

PRINTER PRINTER PRINTER 


SAFETY GLOVES 

REFRIGERANT IDENTIFIER 


712R FULLY-AUTOMATIC 

SERVICE STATION FOR 1234yf 10KG 

INTERNALTANK, SINGLE STAGE 

VACUUM PUMP, SCALE LOCK & 

VEHICLE DATABASE ON SD CARD 

PACKAGE CONTENTS 

• AXONE 5 including IDC5A plus car software 

• Navigator NANO S 

• OBD extension cable 

£ 

2,395 




£ 

3,000 


SAFETY GLOVES 



£ 

3,800 




*All contracts and warranty will be initiated in line with the tool activation date 

OFFER 2 

CODE: UKD2421 

• 12 months car software updates 


£ 

2,295 

Weekly from: xxx† 

CODE: UKD2422 

• 12 months car software updates 


SOFTWARE UPDATES ARE AVAILABLE TO DOWNLOAD VIA THE INTERNET 

£ 

3,395 

Weekly from: £xxx† 

780R BI-GAS 

780R BI-GAS 

780R BI-GAS WITH 

START UP PACK 

780R BI-GAS RID WITH 

START UP PACK 


780R BI-GAS 780R BI-GAS 780R BI-GAS 

PRINTER CLIMATE EFFICIENCY KIT CLIMATE EFFICIENCY KIT 

COVER ADDITIONAL OIL BOTTLE REFRIGERANT IDENTIFIER 

WIFI KIT FOR KONFORT 5KG 1234yf REFRIGERANT ADDITIONAL OIL BOTTLE 

CLIMATE EFFICIENCY KIT 6KG 134a REFRIGERANT 5KG 1234yf REFRIGERANT 

ADDITIONAL OIL BOTTLE SAFETY GLOVES 6KG 134a REFRIGERANT 

£ 

4,500 




UV TORCH 

COVER 

WIFI KIT FOR KONFORT 

£ 

5,395 


SAFETY GLOVES 



UV TORCH 

COVER 

WIFI KIT FOR KONFORT 

£ 

6,150 


DUAL R134a & R1234yf 

AC SERVICE STATION 



Dingbro Ltd 


31



Carbon-Clean 

GROW YOUR BUSINESS WITH 

CARBON CLEANING MACHINES 

CARBON CLEAN MACHINE CC-14 

Introducing these products which only 

use water and cutting-edge HHO engine 

cleaning technology. 

Each machine uses electrolysis to split 

water molecules inot the composite 

elements of oxygen and hydrogen to 

produce oxyhydrogen or HHO gas. 

Professionally remove carbon build-up 

from various parts of any combustion 

engine with our latest technology. We 

offer 3 easy-to-use models to suit your 

workshop. 

Technical Specification 

Description 

Model No 

Input Power 

Output Power 

Display Mode 

Nett Weight 

Dimensions 

Cells 

Vehicle Type 

HHO Engine Cleaner 

CC-14 

220V AC 1PH 

1.4KW/H 

Digital Interface 

40KG 

650(L) x 350(W) x 860(H)(MM) 

Wet Cell / 3x3 Raid Technology 

DPF’S - EARN MORE PROFIT 

BY CLEANING THEM IN-HOUSE 

£ 

5,495 


CARBON CLEAN MACHINE DCS-16 

HIGH PRESSURE PARTS 

CLEANING SYSTEM HPCS-14 


Description High Pressure Parts Cleaning System 

Model No 

HPCS-14 

Operation Pressure 13 Bar 

Driving System 

Cleaning Agent 

Operation Method 

Operation Temp 

Tank Capacity 

Dimensions 

Net Weight 

Power Supply 

NORMALLY 

£ 

4,995 

OFFER PRICE 

£ 

1,895 

Motor Driving 

220V/50HZ/1HP 

Detergent/Water/Air 

Manual Operation 

with Foot Switch 

20-40°C 

50L 

630(L) x 800(W) 

x 1250(H)(MM) 

80KG 

220v/60hz/ph 

HIGH PRESSURE PARTS 

CLEANING SYSTEM HPCS-16 


Description High Pressure Parts Cleaning System 

Model No 

HPCS-14 

Operation Pressure 45-100 Bar 



Operation Method 

Operation Temp 

Tank Capacity 

Dimensions 

Net Weight 

Power Supply 

NORMALLY 

£ 

5,995 

OFFER PRICE 

£ 

3,495 

Motor Driving 

220V/50HZ/1HP 

Detergent/Water/Air 

Manual Operation 

with Foot Switch 

40-60°C 

70L 

680(L) x 1000(W) 

x 1250(H)(MM) 

100KG 

220v/50hz 

Carbon-Clean 

CARBON CLEAN MACHINE DCS-17 


Description 

Model No 



Operation 

Display Mode 

Air Receiver Tank 

Dimensions 

Nett Weight 

Power Supply 

Vehicle Types 

DPF Cleaning System 

DCS-17 

AIR: 4-6 Bar Compressor 

Chemical / Water / Air 

Timer Relay Solenoid Valve 

Analogue 

30L 

1250(L) x 600(W) x 1120(H)(MM) 

160 KG 

220 / 13A 

Blocked DPF’s can be very expensive to 

replace, however this range of DPF cleaning 

machines can clean upto 100% of the carbon, 

soot and ash build-up. 

You’ll be able to clean DPF’s in your 

workshop within a matter of hours, instead of 

sending them away to specilialists who will 

generate the most profits for this service. 

£ 

5,495 


£ 

8,995 



Description DPF Cleaning System 

Model No DCS-16 

Driving System AIR: 2-4 Bar Compressor 

Cleaning Agent Chemical / Water / Air 

Operation Timer Relay Solenoid Valve 

Display Mode Analogue 

Air Receiver Tank 15L 

Dimensions 400(L) x 900(W) x 1120(H)(MM) 

Nett Weight 60 KG 

Power Supply 220 / 13A 

Vehicle Types 


THE PRO-OZONE MACHINE 

Making your personal environment cleaner and safer... 

Due to the covid-19 situation, people are more aware of the need for constant sanitisation 

in all their environments including their vehicles to keep themselves and their families 

safer from virus and bacteria. 

Our machines offer an easy answer to conveniently clean the vehicle interior in the 

matter of minutes. 

The Pro-Ozone state-of-the-art machines are portable units which generate Ozone (O3). 

O3 is a proven method for eliminating the presence of pathogens such as viruses like 

SARS and MERS, and even anaerobic bacteria. 

PRODUCT 

SPECIFICATION 

PRO-OZONE 14 PRO-OZONE 16 PRO-OZONE 18 PRO-OZONE 20 

PZ14 

Our entry level machine. 

Great way to introduce a 

sterilisation service to your 

automotive clients. Can also 

be used in small spaces up to 

35sqm. 

PZ16 

Similar to PZ16 but increased 

03 output meaning the same 

areas can be disinfected in a 

quicker time providing more 

commercial value. 

PZ18 

Ideal for larger spaces up to 

100sqm which means larger 

office spaces, communal 

areas as well as all vehicle 

interiors. 

RATED VOLTAGE AC 220V AC 220V AC 220 AC 220 

RATED POWER 70W 100W 150W 150W 

OZONE OUTPUT 3.5G/Hour 5G/Hour 10G/Hour 20G/Hour 

NETT WEIGHT 2KG 2.6KG 2.6KG 2.6KG 

PZ20 

Top of the range. Cleans up 

to 100sqm in just 30mins. The 

perfect commercial product 

to offer quick and thorough 

cleaning of vehicle interiors, 

offices and other workplace 

locations. 

PACKAGE DIMENSIONS 250 x 160 x 200 370 x 210 x 310 370 x 210 x 310 370 x 210 x 310 

PRICE £ 

249 £ 

289 £ 

389 £ 

489 

Dingbro Ltd 


33



Delphi Technologies 

Delphi Technologies 

EXTRA SPECIAL DIAGNOSTIC OFFERS 

DS150E 

HARDWARE KIT 

CAR AND TRUCK 

SOFTWARE AND VTI PACKAGES 

• All makes, easy to use diagnostic tester 

• Covers European & Asianvehicles to current date 

• Fault codes, live data, actuator operation, coding functions and service re–sets 

• 2GB Flight Recorder 

• Illuminated 16 pin connector 

• Works with most laptops and PC’s inc Windows 10 

• Free Manufacturer user training 

PART NO: DS150 (SV10546) 

PROMOTIONAL PRICE 

UNTIL 31/12/2020 

£ 

995 

NORMAL PRICE 

FROM 1/1/2021 

£ 

1,340 

DELSV10546 

WHAT’S INCLUDED IN THE CAR AND TRUCK PACKAGES: 

• Vehicle Technical Information (VTI) is an additional software 

• package that integrates with your OS software, giving the technician 

the complete repair solution. 

• Whatever vehicle you are working on with the OS software, just press 

the “I” button and it will carry over that vehicle ID 

and present you with all the technical information 

relevant to that particular vehicle. (Previously only 

available via a OS tool, this can now be purchased 

as a standalone product with no need for a Delphi 

DS tool) 

GRAB 

YOURS 

NOW!! 

Price does not include software 

DS450 

TABLET AND MINI VCI KIT UK 

• Twice as fast as previous tablet 

• VCI as DS450 

• Rugged case with Active pen and kickstand 

• 10.1” WUXGA anti-glare touch screen 

• 128GB SSD storage and 8GB RAM 

• Bluetooth wireless technology 

• Front (1080p) & rear (1920p) webcam 

• Intel ® Celeron N4100 4 cores processor 

PART NO: DS450 (SV11438) 

NEW TABLET 

• Technical service bulletins 

(SmartFIX’”) 

• Verified fixes and tips 

(SmartCASE’”) 

SOFTWARE 

SV10516 

(1YR Car Software) 



£ 

595 

• Comfort wiring diagrams. 

• Fuses and relays 

• Locations 

• Vesa guided diagnostics 

SV10598 

(3YR Car Software) 



£ 

1,375 

• Maintenance 

• Adjustment data 

• Lubricants 

• Repair manuals 

SV10821 

(1YR Heavy Duty Software) 



£ 

625 

SV10516 

(1YR Heavy Duty Software) 



£ 

1,395 

• Recall data 

• Repair times 

• Technical drawings 



£ 

1,945 

NORMAL PRICE 

FROM 1/1/2021 

£ 

2,515 

DELSV11438 

NORMAL PRICE 

FROM 1/1/2021 

£ 

615 

NORMAL PRICE 

FROM 1/1/2021 

£ 

1,415 

NORMAL PRICE 

FROM 1/1/2021 

£ 

645 

NORMAL PRICE 

FROM 1/1/2021 

£ 

1,435 


VTI 

SV60156 

DOIP ADAPTER 

• Adapter is required to use the DoIP function within 

the DS Diagnostic Tool 

• Enables a connection between the DS Diagnostics Tool and a vehicle’s ECU using 

IP protocols 

• Compatible with the Braking and 

• Engine Management systems 

• Covers the Service Light Reset as well as Fault Code Reading & Clearing 

functionalities 

PART NO: SV60156 



£ 

180 

£ 

185 


NORMAL PRICE 

FROM 1/1/2021 

Covers a number of Jaguar, 

Land Rover & Volvo models including: 

• Jaguar F-Pace 2018 

• Jaguar XE E2018 

• Jaguar XF 2018 

• Land Rover Discovery 5 2017 

• Land Rover Discovery 5 2018 

• Land Rover Sport 2017 

• Land Rover Sport 2018 

• Land Rover Range Rover Sport 2017 

• Land Rover Range Rover Sport 2018 

• Land Rover Range Rover Velar 2018 

• Volvo 590 2017 

• Volvo 590 2018 

• Volvo V90 Cross Country 2017 

• Volvo V90 Cross Country 2018 

• Volvo XC40 2018 

• Volvo XC60 2018 

• Volvo XC90 2016 

• Volvo XC90 2017 

• Volvo XC90 2018 

SV11510 

(1YR VTI Car Ultimate 

for DS-Users) 



£ 

405 

NORMAL PRICE 

FROM 1/1/2021 

£ 

520 

SV60207 


for DS-Users) 


TILL END 2021 

£ 

1,262 

SV60135 


Standalone) 



£ 

435 

NORMAL PRICE 

FROM 1/1/2021 

£ 

550 

SV60161 


Standalone) 


TILL END 2021 

£ 

1,425 

SV11519 

(1YR VTI Truck Business 



£ 

505 

NORMAL PRICE 

FROM 1/1/2021 

£ 

525 

SV11518 

(1YR VTI Truck Professional) 


TILL END 2021 

£ 

280 

SV11520 

(1YR VTI Truck Ultimate) 



£ 

610 

NORMAL PRICE 

FROM 1/1/2021 

£ 

630 

SV60163 

(3YR VTI Truck Ultimate) 



£ 

1,425 

NORMAL PRICE 

FROM 1/1/2021 

£ 

1,465 

Dingbro Ltd 


35



Maverick Diagnostics 

DID YOU KNOW YOU CAN BUY 100% GENUINE OEM 

TOOLS WITH FULL TECHNICAL SUPPORT? 

That’s right, the same tools that dealers use! 

ALFA ROMEO/FIAT MICROPOD 2 

TOOL BUNDLE 

BMW ICOM NEXT A BUNDLE 

TOOL BUNDLE 

MERCEDES BENZ XENTRY 

TOOL BUNDLE 

• Brand new Panasonic Toughbook CF-D1 

• 100% genuine Actia XS 2G 

• Conforms to SAE J2534-1 and J2534-2 

• EURO 5 & newer only 

Maverick Diagnostics 

PEUGEOT/CITROEN PSA XS A.1281 

TOOL BUNDLE 


• 100% genuine PSA XS A.1281 

• Compatible with all Citroen, Peugeot and DS 

vehicles 1996 onwards 

• Compatible with Vauxhall vehicles including 

Corsa F from 2020 onwards 


• 100% genuine Micro Pod 2 

• Works as a direct replacement for the 

wiTECH POD 

• Works with your current wiTECH 

software 

• 100% CAN equipped vehicle coverage 

to current 

• Brand new Panasonic Toughbook 

CF-D1 

• 100% genuine BMW ICOM Next A 

• Supports diagnostic & programming 

functions for BMW, BMW-I, MINI, 

Rolls-Royce & BMW Motorrad 

ONLY 

£ 

3,495 

ONLY 

£ 

3,845 

• Software License: wi-TECH Diagnostic 

Application purchased through Maverick 

Weekly from:£18.55† 


• A Tech Authority Software Subscription 

is required to access module re-flashing 

information, TSBs, wiring diagrams and 

repair information 

VAUXHALL/OPEL MDI 2 

TOOL BUNDLE 

VOLVO DICE 

TOOL BUNDLE 



• 100% genuine Vauxhall/Opel MDI 2 

• 100% genuine Volvo DiCE 

ONLY 

£ 

5,490 

ONLY 

£ 

3,295 

• GM MDI2 is the newest released GM factory 

scan tool and begins its coverage in model 

year 2010. MDI, when combined with the 

Global Diagnostic System 2 (GDS2) software 

application, allows servicing of GM’s new 

models 

• Fully DOIP compatible for use with the latest 

XC range 

• Includes DOIP adapter 



FORD VCM 2 

TOOL BUNDLE 

JAGUAR/LAND ROVER (JLR) 

TOOL BUNDLE 

ONLY 

£ 

3,699 

ONLY 

£ 

3,275 


• 100% genuine Ford VCM 2 

• 12 months Genuine Ford IDS/FDRS 

licence included 

• VCM II will support all current Ford 

European production vehicles up to 2020 

and beyond 

• CFR and DLC cables 

• USB wireless cards 

• Panasonic Toughbook CF54 ‘A’ grade 

• 100% genuine Jaguar Land Rover 

Pathfinder & VCI 

• Jaguar Land Rover software pre-loaded 

• The new JLR Pathfinder DOIP VCI is the 

only unit that will be compatible with all 

JLR vehicles with the new MY17 vehicle 

architectures 

• In addition to the 17MY vehicle line 

applications, the DOIP VCI will be capable 

of interfacing with 14-16MY Multi- 

CAN architecture vehicle lines on the 

Pathfinder diagnostic system 


VAG VAS6154/A 

TOOL BUNDLE 


• 100% genuine VAG VAS6154A 

• The VAS6154A can be used with all VW Audi 

Skoda vehicles from 2000 onwards including 

new & future models under production 

• Assistance with VASS registration 


CODE WIZARD PRO 2 

• USB key with 200 tokens loaded 

• All updates are free of charge 

• Supports about 60 vehicle brands 

• Calculation of security codes for 

immobiliser key programming and 

electronic unit synchronization, calculation 

of mechanical KEY codes by VIN, 

passwords for Coded Access to security 

functions of OEM software and much more. 

ONLY 

£ 

4,990 

ONLY 

£ 

3,750 

ONLY 

£ 

3,845 

ONLY 

£ 

220 




Dingbro Ltd 


37



Autel 

Autel 

MAXIDAS 

DS 808 EU 

24 MONTHS 

WARRANTY 

& SUPPORT 

INCLUDED 

£ 

999 £ 799 

exc. VAT 

exc. VAT 

INCLUDES EXTENDED: 

2 YEARS WARRANTY 

2 YEAR FREE UPDATES 

MAXISYS 

MS908S 

• Bluetooth VCI Connectivity 

• 80+ Manufacturers 

• TMPS Diagnosis and Programming 

• Built-in rechargeable lithium-ion 

battery for up to 8 hours of continuous 

operation 

• Read & Clear Codes 

The Maxisys MS908S is 

built on the multi-tasking 

Android operating system 

• Live Data/Record/Playback 

• Auto Vin & All Module Interrogation 

• SAS/BMS/DPF Service Functions 

• Electronic Parking Brake 

• Service Mileage/Interval Reset 

• European software 

The MaxiSys MS908S is the UK’s best selling premier Autel diagnostic tool with a 

15 second boot up speed built on the multi-tasking Android operating system. 

The MS908S includes a number of great features covering over 80 manufacturers 

with full diagnostics, service function and programming, 8 Mega-pixel Camera, 

64GB Internal Hard Drive and Wireless Bluetooth diagnostics via the Vehicle 

Communication Interface (VCI). 

Both the MS908S & MS908S PRO are supplied with 

Pre-16 pin OBD connectors for the older vehicles 

24 MONTHS 

WARRANTY 

& SUPPORT 

INCLUDED 

9.7” LED MULTI- 

TOUCH DISPLAY 

2 YEARS INCLUSIVE 

UPDATES WITH 

THE MS908S PRO, 

MS908S & 

MS906 

MAXISYS MS908S 

£ 

745 

SUPER FAST 

UNBEATABLE VALUE 

The DS808EU is Autel’s base Pro-Range tool. The DS808EU is the 

‘little brother’ of the MaxiSYS MS906 and the UK edition is loaded with 

the same software as the MS906, making the DS808EU fabulous 

value for money. 

The DS808EU is powerful with 4 core processor, colour 7” touch 

screen, built in lithium battery, 32GB of memory and Smart AutoVIN 

technology. The DS808EU is a smaller tablet than the MS906 and is 

not supplied with pre-OBD connectors. This stream-lining enables us 

to significantly lower the price to our end customers. 

• Extensive vehicle coverage for more than 80 US, Asian and European 

vehicle makes 

• Exceptional OE-Level system coverage for all electronic systems 

• Complete capabilities for codes, live data, active test, ECU information, 

adaptation, matching, etc. 

2 YEARS SOFTWARE 

UPDATES INCLUDED 

• 32GB Hard Drive 

• 80+ Manufacturers 

• 24 Month UK Warranty 

• European Software 

• Tablet Device Android Powered 

• Chrome Web Browser 

Future 12 months Update 

£ 

399 

exc. VAT 

Android 

1024x600 

MAXITPMS TS 408 

ONLY 

£ 

249 

MAXITPMS TS 508 

ONLY 

£ 

299 

MAXITPMS 

ONLY 

£ 

349 

TS 508 WiFi 

1.5GHz 

Cortex-A9 

Ultra fast 

power on 

OPTIONAL COMPATIBLE 

ACCESSORIES 

32G internal 

memory 

3200mA 

lithium-polymer 

battery 

WiFi 

Oil and water 

screen resistant 

15 SECOND 

BOOT UP 

BUILT ON ANDROID 

OPERATING SYSTEM 

• Autel products meet international quality and 

environmental regulations, including as FCC, CE and RoHS 

MAXISYS 

MS908S PRO+J2534 

The MaxiSYS MS908S Pro with J2534 

has extra programing functionality 

included in the tools software and 

also allows you to subscribe to your 

manufacturer clouds and download 

software specifcally for a vehicle. 

The MS908S Pro with the optional 

extra J2534 pass through device 

allows even greater in-depth vehicle 

programming, making it ideal for the 

more specialist repair garages and 

bodyshops. 

• Perform dealer-level diagnostics 

(where offered by the vehicle 

manufacturer) 

• Download software updates 

including emission-related ECUs 

• ECU updates for a wide range 

of vehicle makes and models 

• Access OE technical data and service 

schedule information 

Fully upgradeable with 

the following bolt-ons: 

• Upgradable to ADAS 

• Add an MP408 oscilloscope 

• Add an MV105 borescope 

Fully upgradeable with 

the following bolt-ons: 

• Upgradable to ADAS 

• Add an MP408 oscilloscope 

• Add an MV105 borescope 

• Add a pass-through J2545 

to standard MS908 

24 MONTHS 

WARRANTY 

& SUPPORT 

INCLUDED 

The most extensive 

system coverage 

for 80+ manufacturers 

 

✠ 

Wireless Bluetooth VCI 

Android Powered 

8 Mega–pixel Camera 

9.7”/1024 x 768 Screen 

64GB SSD Hard Drive 

Chrome Web Browser 

Portable Tablet Device 

8 Hour Battery Life 

MAXISYS MS908S 

£ 

1,995 

Weekly from: £ 10.59 † 

Autel Pass Thru Technology with the J2534 Pass through device 

In addition to all the features found on the MaxiSys MS908, the MS908 PRO and J2534 offers further 

diagnostic capability with a Higher Level of Programming functions along with pass-through 

capability including Key Programming. 

MAXISYS MS908S PRO 

£ 

2,495 


MAXISYS MS906 

£ 

475 



£475.00 

£ 

945 

Dingbro Ltd 


39



Rowley Spray Booths 

Bendix Brake Service Tools 

Rowley Spraybooths have over fourty years experience in the manufacture, installation and 

maintenance of Spraybooth ovens in the finishing / refinishing industry. All Rowley Spraybooth oven 

equipment is manufactured in the UK at their manufacturing facility located in Cannock, Staffordshire. 

AERO-ECO 

SPRAYBOOTH OVEN 

Featuring dynamic air moving plant and an energy efficient 

control system the AERO-ECO Spraybooth oven is designed to 

deliver ultimate economy with ultra-low running costs. 

The AERO-ECO Spraybooth has a spacious cabin constructed 

from modular single ‘skin’ (or double ‘skin’) bright galvanised 

steel panels with good lighting and wide access component 

doors. Utilizing rear chest extraction and compact air handling 

plant the AERO-ECO Spraybooth provides the perfect painting 

environment for any type of work. 

The tunnel airflow design provides excellent paint over spray 

mist clearance during spraying operations and uniformity of air 

temperatures on spray and bake modes. 

AERO-MIDI 


FROM ONLY 

£ 

12,999 


BENDIX FLUTEST 

Brake Fluid Tester 

with optional printer 

capability 

• Accurate, reliable and repeatable results 

• Operates off 12V power supply (vehicle own battery) 

• User friendly – LCD screen instructions guide 

operator through complete testing cycle 

• Measures up to 320˚C/608˚ suitable for use on all 

grades of new & used brake fluids, including racing fluids 

• Multilanguage display – 19 languages, selectable by user 

• Compatible with printer for test results (987AB2430) 

BRAKE 

BLEEDERS 

PART NO: 

987AB2350 

ONLY 

£ 

210 

OPTIONAL 

PRINTER 

SEE YOUR 

TEST RESULTS 

ON PAPER 

ONLY 

£ 

220 

Part No: 

987AB2430 

WORLD LEADING TECHNOLOGY 

PORTABLE OPERATION WITH 

12V POWER SUPPLY 

The spacious AERO-MIDI cabin is constructed using modular 

double ‘skin’ insulated panels to give good thermal retention, 

rigidity and sound dampening. Utilizing a rear chest extraction 

expensive underground extraction pit works are not required 

and this allows the installation to be easily relocated. 

This tunnel airflow design provides excellent paint over spray 



AERO-MAXI 


The AERO-MAXI Spraybooth oven range is a high specification 

Spraybooth oven that provides the highest quality environment 

for all types of paint application and low bake curing operations. 

The larger AERO-MAXI Spraybooth oven cabin is constructed 

using modular double ‘skin’ fully insulated panels to give good 

thermal retention, rigidity and sound dampening. Utilizing a 

rear chest extraction expensive underground extraction pit 

works are not required and this allows the installation to be 

easily relocated. 

This tunnel airflow design provides excellent paint over spray 



AERO-INDUSTRIAL/COMMERCIAL 

SPRAY BOOTH OVEN 

The Industrial and Commercial Spraybooth oven range can be 

designed to meet customer’s specific requirements for 

Spraybooth ovens. The flexible modular design allows the cabin 

size and air flow requirements to be made to suit the products 

being painted. 

IDEALLY SUITED FOR USE WITH 

WATER BASED PAINT SYSTEMS 

FROM ONLY 

£ 

15,495 


IDEALLY SUITED FOR USE WITH 

WATER BASED PAINT SYSTEMS 

FROM ONLY 

£ 

18,995 


CALL NOW 

FOR A QUOTE 

BENDIX 

Pressure Brake 

Bleeder 12V 1.5 Bar, 1.25L 

• Pressure brake bleeding is the only method 

approved by brake system manufacturers 

• Full fluid exchange in approx. 15 minutes by a single operator 

• Portable operation with 12V power supply (vehicle own battery) 

• No compressed air used, therefore no risk of contamination 

of the fluid 

• Float switch to ensure pump stops when new fluid level is low 

• Supplied with euro-cap and bleed bottle 

• Suitable for clutch hydraulic bleeding as well 

• Fluid change capacity 1.25L 

BENDIX Professional 

Pressure Brake Bleeder 

0-3 Bar 5L (available 

as 12v or 240v mains 

variant) 

• Pressure brake bleeding is the only method 

approved by brake system manufacturers 

• Full fluid change can be completed by a single 

operator in approx. 15 minutes 

• Fully adjustable digital pressure controller; 

0 – 3.0 Bar 

• Draws directly from 5L brake fluid container, 

housed within tester compartment, avoids 

contamination 

• Auto cut-off prevents air entering system if fluid 

supply is interrupted 

• Portable unit with carry-handle – only 

weighs 9.0Kg 

• Operates from 12V power supply 

• Heavy duty pump for long service life 

• Coiled sprung fluid delivery hose for ease of use 

and storage 

• OEM approved 

12V PART NO: 

987AB2360 

240V PART NO: 

987AB2370 

ONLY 

£ 

495 

PART NO: 987AB2380 

ONLY 

£ 

295 

APPROVED BY BRAKE 

SYSTEM MANUFACTURERS 

BENDIX Brake Bleeder 

Functions include: 

• Full fluid change can be 

completed by a 

single operator in approx. 

15 minutes 

• Heavy duty pump for longer 

life & continuous use 

• Fully adjustable analogue 

pressure controller, 

0.5-4.0 bar 

• No compressed air used, 

therefore no possibility 

of contamination of the fluid 

• Storage facility for fluid 

collection container & 

accessories 

• Suitable for use on car 

& LCV brake systems 

& also on HGV clutches 

• 6L fluid change capacity 

• Stainless steel construction 

SUPPLIED COMPLETE WITH 

MULTI-VEHICLE CAP 

& EUROPEAN CAP KIT AS 

SHOWN 

PART NO: 987AB2470 (12 VOLT) 

OFFER PRICE 

£ 

529 

PART NO: 987AB2480 (240 VOLT) 

OFFER PRICE 

£ 

549 

Dingbro Ltd 


41



Bendix Diagnostics 

Bendix ADAS 

WHAT’S POWERING 

YOUR WORKSHOP? 

LATEST IN DIAGNOSTIC TECHNOLOGY 

In-depth software including a vast vehicle coverage and powerful specialist test functions, 

extremely fast live data and graphing, along with module coding capabilities. 

OPTION 1 with 1 years software 

£ 

1,395 

Normally £ 1,995 

PART NO: 

Weekly from: £ 7.40 † 989AA0650 

INTEREST FREE 

OPTIONS AVAILABLE 

(subject to terms and conditions) 

COMES COMPLETE WITH 

BMW & MERCEDES 

ROUND PIN ADAPTERS 

BENDIX DIAGNOSTIC & SERVICE TOOL 

BENDIX ADAS PRO 

The Bendix ADAS Pro is designed to work with the Bendix diagnostic tools and activates the full ADAS functionality and includes all 

the hardware required to get started with camera calibrations. Perfect for use by service and repair shops, windscreen replacement 

centres and tyre specialists. 

Our easy to use software will guide you through setting up the system. 

Optional targets, laser reflectors, side and rear mats expand the system to suit your business and allow for calibration of 360 degree 

cameras and rear calibrations. The targets can be purchased individually as required, or in value packs. 

Digital ADAS is the ideal solution for busy workshops shops with a large turnover of vehicles as it includes all supported car 

manufactures targets, which are displayed on a large 65” monitor with intelligent display technology to reduce setup time. The 

system can also be expanded with optional reflectors and mats to cover, night vision, 360 degree and rear radar calibrations. 

• Simple to set up with one technician in less than 5 minutes 

• Industry approved with full audit trail 

• Always up to date - simply download new targets as they are released 

• Use less workshop space - No target panels to store or damage 

• Patented technology aligns the image to the car. 

• Use in any light conditions with 4K monitor. 

FROM 

£ 

5,495 

FROM 

£ 

18,995 



PARTS ALLIANCE 

DIAGNOSTICS 

MONSTER DEAL!! 

OPTION 2 

with 3 years software 

£ 

1,895 

Normally £ 2,495 

PART NO: 

989AA065K 


FOR MORE DETAILS OR TO ARRANGE A DEMONSTRATION CONTACT YOUR LOCAL BRANCH 

ADAS PRO FEATURES: 

• Electrically adjustable frame for ease of use and accuracy 

• 2 adjustable wheel clamps with level indicators and laser 

reflector 

• Frame mounted lasers for accurate measurement 

• VAG group target 

• Front radar kit – optional extra 

• IMI accredited support staff 

ALL BENDIX TOOLS 

ARE ADAS READY 

DIGITAL ADAS FEATURES: 

• 65” monitor mounted on an adjustable intelligent frame 

• All available front camera boards included 

• Wi-Fi connectivity 

• 2 adjustable wheel clamps with reflectors 

• Frame mounted laser for fast accurate set up 

• Front laser reflector panel included as standard 

FOR MORE DETAILS OR TO ARRANGE A DEMONSTRATION CONTACT YOUR LOCAL BRANCH 

Dingbro Ltd 


43



Bosch 

Bosch 

USE THE 

BEST TO 

TEST! 

Launch of the new KTS 250: 

Diagnostic scan tool 

KTS 250 an Android based handheld 

diagnostic scan tool with automatic VIN 

identification, fully optimised software and 

workflows for faster navigation. 

The simultaneous diagnostic capability 

enables the tester to communicate with 

multiple ECUs at the same time - speeding 

up processes such as the vehicle system 

overview, activation of special functions 

and readout of actual values. 

The tester is "Diagnostic over IP" 

(DoIP) enabled. This provides you with 

an intelligent solution for tomorrow's 

requirements today. 

USE THE 

BEST TO 

TEST! 

KTS 350: Next generation 

all-in-one solution. Five times 

faster than it's predecessor 

Mobile all-round solution for control unit diagnosis, troubleshooting, 

repair and maintenance. Delivered plug & play with Windows 10 

and pre-installed ESI[tronic] 2.0 software - ready for licencing 

(based on your needs). It has integrated ethernet interface (DoIP), 

which opens up for the possibility to transfer data up to 100 times 

faster than CAN technology. 

ADVANCED TECHNOLOGY 

IN ONE COMPACT DEVICE 

ONLY 

£ 

2,995 


FROM 

£ 

1,895 


CALL 0121 749 8801 AND SPEAK TO ONE OUR 

GE SPECIALISTS FOR THE BEST BOSCH DIAGNOSTIC DEAL 

The Bosch KTS 590 

Optimally suited for the use of the 

diagnostic software ESI[tronic] 2.0, the 

Bosch KTS 590 can operate several 

vehicle interfaces in parallel so vehicle 

manufacturer portals for diagnostics and 

reprogramming according to Euro 5/6 

(PassThru) can be operated efficiently. 

The module is Diagnostic over IP (DoIP) 

ready, along with 2-channel oscilloscope 

and multimeter. Bluetooth class 1 (up to 

100m in range). 

It is a must for the ambitious workshops. 

What's included in the 

Masterpack & EBR subscription 

SD - Vehicle diagnosis: 

The latest diagnostic data for passenger cars and 

light commercial vehicles for over 130 brands. 

SIS - Vehicle troubleshooting instructions 

The troubleshooting instructions reliably guide 

you step-by-step to the cause of the fault. 

EBR/TSB - Experience-Based-Repair - Known Fixes 

Find the right solution within seconds, even for 

challenging troubleshooting cases. Includes the module - 

technical service bulletins (TSB). 

M - Vehicle mechanics and maintenance schedules 

Maintenance information tabs contain all vehicle data 

such as service schedules, needed parts and much more 

with direct link to diagnostic functions. 

P - Comfort systems wiring diagrams 

Giant database including wiring diagrams for all 

important systems such as comfort systems and 

bus systems for optimal efficiency. 

www.boschesitronic.com 

EBR - Experience Based Repair. 

"Crowd sourced repair verification 

Already includes 750,000 known repairs, the database is 

growing day by day! Simply search for the fault codes or 

symptoms to vehicle problems identified by technicians in 

the field and online. All fixes have been validated by our own 

engineers. 

EBR may also be offered as a standalone software solution 

which does not require a KTS module. 

Get a subscription today and save hours in future fault finding. 

EBR Standalone software includes 

A 

Basic ESI[tronic] 

✓ 

EBR 

Experience-based 

repair—Known 

✓ 

TSB 

Technical 

Service Bulletin 

FROM 

£ 

1,995 


Stay up-to-date 

New vehicle models are available in ESI[tronic] 2.0 with 

coverage, as soon as six months after their market launch. 

Online updates available, which run silently in the background 

with no user intervention required. 

FROM 

£ 

199 

Dingbro Ltd 


45



Bosch 

Bosch 

DAS 3000 S20 

SOFTWARE GUIDED CALIBRATION 

Calibration tool for front facing camera & radar systems with 

computer-based positioning and adjustment. 

Designed for professional all-makes workshops, bodyshops and windscreen specialists 

that want a quality tool that reduces the setup times significantly. 

Reduced setup times! 

Faster & easier setup with 1-pager setup 

instructions, drive axis cameras and guided 

positioning software 

8 

1. Distance measure bar with two 

cameras for line-up to driving axis 

2. Combined VW target & radar reflector 

3. Precision measurement bar to mount 

vehivle specific target boards 

6 

7 

4. Distance measurement aid (post with 

reference panel) 

5. Universal wheel clamps with targets 

for aligning the drive axis 

9 

6. Optional starter kit with storage box 

and multiple target boards 

2 

7. PC tray with optional DCU 220 

industrial laptop to run the ADAS 

positioning software 

1 

4 

SCALABLE, 

FAST AND ACCURATE 

5 

3 

8. Pitch angle adjustment device - to tile 

the entire frame back and forth 

9. Spring loaded stamp brakes to lock the 

trolley in a fixed position 

FROM 

£ 

7,495 


Multi-brand target support & all-makes 

capability with vehicle specific calibration via 

Bosch ESI[tronic] 2.0 software. 

ESI[tronic] 2.0 

Online 

DAS 3000 

TARGET STARTER KIT 

Targets/content 

Starter Kit 

1.1 

S P09 000 000 

Starter Kit 

1.2 

S P09 000 001 

Starter Kit 

2.1 

S P09 000 002 

Starter Kit 

2.2 

S P09 000 003 

Storage Container 4 4 4 4 

Mercedes 

Type 1 4 4 4 4 

Universal 

Type 1 (Kia, Hyundai, Fiat, PSA, Vauxhall) 4 4 4 4 

Mazda 

Type 1 4 4 

Mazda 

Type 2 (Set) 4 4 

Nissan 


Nissan 


Toyota 

Type 1 4 4 

Toyota 

Type 2 4 4 

Honda 

Type 1 (Set) 4 

Honda 

Type 3 4 

Universal 

Type 2 (Renault, Smart, Vauxhall) 4 4 

Mitsubishi Type 1 4 

Total targets in the kit 3 4 9 13 

Parts Alliance Price £ 

1000 £ 

1000 £ 

1000 £ 

1000 

Dingbro Ltd 


47



SIP & HELVI ® Welding 

SIP AUTOPLUS MINI 130 

SYNERGIC 

INVERTER WELDER 


• (MIG): 30 - 130A: 130A @ 35% duty cycle 

(MMA) 30 - 115A: 115 @ 35% duty cycle 

• 2 processes: MIG & MMA 

• Dual Purpose: Gas & Gasless MIG 

• Synergic control 

• Infinitely variable power adjustment 

• Superior welding arc stability 

• Lightweight and portable - 7.5kg 

• Uses 100mm diameter minispools 

for MIG welding 

• Supplied with: Integrated 

MIG torch, earth lead 

and clamp, electrode lead 

and holder, gas hose, 

disposable welding gas 

bottle brackets 


ONLY 

£ 

219 

MIG & MMA 

PROCESSES 

DUAL PURPOSE 

GAS/GASLESS 

SIP AUTOPLUS 180X 

MIG/ARC 


& WELDING CART 

PART NO: 05794CART 

ONLY 

£ 

399 

FREE 

WELDING 

CART 

MIG & MMA 

PROCESSES 

DUAL PURPOSE 

GAS/GASLESS 

HELVI ® FOX MIG/ARC 

DUAL-PURPOSE 


• 230v 16A input supply 

• Synergic control; quick setup control (set and weld) 

• Output Current: MIG 25 - 170A / MMA 25 - 170A 

• Duty Cycle: MIG 170A @ 25% / MMA 170A @ 25% 

• MIG wire diameter: 0.6, 0.8 & 1mm 

• MIG spool size: 100 - 200mm 

• MMA Electrode size: 

1.6, 2, 2.4 & 3.2mm 

• Electrode type: 6013 

• Weight: 11.5kg 


ONLY 

£ 

569 

THREE 

YEAR 

WARRANTY 

MADE IN 

ITALY 

LEMANIA ENERGY 

ADVANCED 

BATTERY CHARGERS 

LEMANIA ENERGY Advanced Battery Chargers 

The GX is the ultimate battery charging, 

support and diagnostic tool. 

Combine intelligent charging, maintenance, 

supply, reconditioning and testing into one 

simple process with these easy-to-use wallmountable 

Advanced Battery Chargers. 

THREE 

YEAR 

WARRANTY 

03571 

HELVI ® MONOMIG PROFESSIONAL 

TRANSFORMER MIG WELDERS 

• High Power Output: Ideal for automotive & light sheet metal applications 

• 30A Low Current Performance: Ideal for welding car body panels 

• Turbo Fan Cooled: Increased duty cycle 

• Copper Wound Transformer: Proven technology & 

“Work Horse” durability 

• Spot Welder Timer: Precise timing for specific tasks 

• Heavy-duty 2 roll metal wire feed system 

• Welds: Mild steel, stainless steel and aluminium 

• Wheel-mounted design with Integrated bottle carrier 

25348 25349 

25349 

LOW CURRENT 

PERFORMANCE INTEGRATED 

BOTTLE CARRIER 

MADE IN 

ITALY 

THREE 

YEAR 

WARRANTY 

PART NO 25348 25349 

MODEL 

Helvi Monomig 246 

Compact MIG Welder 

Helvi Monomig 286 

Compact MIG Welder 

INPUT SUPPLY 230v (32A) 230v (40A) 

OUTPUT CURRENT 30 - 250A 30 - 280A 

DUTY CYCLE 200A @ 35% 250A @ 35% 

MIG WIRE SIZE 0.6 / 0.8 / 1mm 0.6 / 0.8 / 1.0 / 1.2mm 

MIG SPOOL SIZE 200 - 300mm 200 - 300mm 

WEIGHT 73.6kg 80.0kg 

ADDITIONAL 

FEATURES 

PRICE 

2 Roll Metal Wire Feed 

Supplied with: 

3 Metre MB15 MIG Torch 

3 Metre Earth Lead 

0.6 - 0.8 Steel Roller 

Gas Regulator 

ONLY 

£ 

1,259 

2 Roll Metal Wire Feed 

Supplied with: 

3 Metre MB15 MIG Torch 

3 Metre Earth Lead 

0.6 - 0.8 Steel Roller 

Gas Regulator 

ONLY 

£ 

1,389 

03572 03573 03574 

SIP FX PORTABLE 

WELDING FUME EXTRACTOR 


• Max. flow rate 250m 3 /hr 

• Max. suction 110m 3 /hr 

• 85% filtration 

• 3 stage filters: 

1: Metallic Spark Arrestors G25% 

2: Cartidge Filter F5 85% 

3: Active Carbon Panel 

• 65dB(A) noise level 

• Suitable for medium/low 

concentrations of pollutants 

• Intermittent operation with 

adjustable motor speed regulation 

• Flexible extraction hose 


ONLY 

£ 

699 

SIP WELDING FUME EXTRACTOR ACCESSORIES 

PART NO DESCRIPTION PRICE 

WE08-00003 Anti-spark Metallic Filter (for 05800) ONLY £ 

22 

WE08-00004 Cartridge Filter - 85% efficient (for 05800) ONLY £ 

54 

WE08-00005 Carbon Filter (for 05800) ONLY £ 

97 

SIP PROFESSIONAL FX-EH 

MOBILE 

WELDING FUME 

EXTRACTOR 


• Max. flow rate 2500m 3 /hr 

• Max. suction 1200m 3 /hr 

• 99.5% filtration 

• 3 stage filters: 

1: Metallic Spark Arrestors G25% 

2: Corrugated polyester fibre pre-filter 

3: Absolute filter H13 HEPA 95.5% 

• 73dB(A) noise level 

• High performance centrifugal extraction fan encased 

in a soundproof compartment 

• 3 metre flexible extraction arm 


ONLY 

£ 

1,499 


PART NO DESCRIPTION PRICE 

WE08-00008 Absolute Filter (for 05802) ONLY £ 

236 

WE08-00009 Anti-spark Metallic Filter (for 05802) ONLY £ 

31 

WE08-00010 Pre Filter (for 05802) ONLY £ 

27 

PART NO 03571 03572 03573 03574 

MODEL 

Advanced Battery 

Charger GX2 


Charger GX5 


Charger GX10 


Charger GX15 

CHARGING VOLTAGE 12V 12V 12V 12 / 24V 

AMPS 2A 5A 10A 15A 

CHARGING CYCLE 8 Stage 8 Stage 10 Stage 10 Stage 

CABLE LENGTH 1.8m 1.8m 2.0m 2.0m 

CAN-BUS COMPATIBLE 4 4 4 8 

DIGITAL INTERFACE Advanced Advanced Advanced Advanced 

RECONDITIONED MODE 8 4 4 4 

SUPPLY MODE 8 4 4 4 

TEST MODE 4 4 4 4 

LEAD MODE 4 4 4 4 

LITHIUM 4 4 4 4 

ACCESSORIES 

Quick Connector, Clamps, Eyelets, 

12V DC Car Adaptor 





Quick Connector, Clamps, Eyelets 

WATER/DUST RESISTANT IP65 IP65 IP65 IP20 

WEIGHT 0.5kg 0.6kg 1.2kg 1.2kg 

USAGE Car Car Car Car / Truck 

PRICE ONLY £ 39 ONLY £ 49 ONLY £ 109 ONLY £ 149 

Dingbro Ltd 


49



SIP Starter Chargers / Boosters 

AER SERVICE Exhaust Gas Extraction 

SIP STARTMASTER DIGITAL 

STARTER CHARGERS 

PART NO 05545 05546 05548 

MODEL Startmaster PW550 Startmaster PWT6500 Startmaster PWT9500 

INPUT SUPPLY 230v 230v 230v 

INPUT CURRENT 16A 20A 50A 

CHARGING VOLTAGE 12 / 24V 12 / 24V 12 / 24V 

MAX. CHARGE CURRENT 45A 55A 100A 

AVERAGE CHARGE CURRENT 30A 36A 70A 

FLAT BATTERY 300A 400A 600A 

MED CHARGE BATTERY 200A 260A 400A 

MAX. BATTERY CAPACITY 450Ah 540Ah 1000Ah 

CHARGE RATE SETTINGS 4 4 4 

BATTERY TYPE SELECTION 

Pb (LEAD), GEL, CaCa 

AGM, START-STOP 





WHEEL MOUNTED 4 4 4 

ADDITIONAL 

FEATURES 

PRICE 

Charging Timer 

Auto Boost 

ONLY 

£ 

419 

SIP RESCUE PAC 1600 

12V BOOSTER 

• 1600A boost peak rate 

• 700A cranking rate 

• 12V DC output socket 

• LED charge indicators 

• True 22Ah battery capacity 

• Supplied with charger 

• Lightweight 8.5kg 


ONLY 

£ 

139 

SIP SC 8000 

12V CAPACITOR 

BOOSTER 

• 12v heavy-duty capacitor start booster 

• Uses powerful 18x 600F ultracapacitors 

• 8000A boost peak/1400A cranking rate 

• Batteryless design with 1mil+ life cycles 

• No internal battery maintenance needed 

• Charge from running vehicle in 15 seconds 

• LED indicators for accurate boost level 

• Built-in safety fuse and ON/OFF switch 

• Supplied with a fully automatic charger 


ONLY 

£ 

449 


Auto Boost 

ONLY 

£ 

479 

1,400A 

CRANKING 

RATE 

CHARGE FROM 

RUNNING VEHICLE 

IN 15 SECONDS 

SWISS 

MADE 

TWO YEAR 

WARRANTY 


Auto Boost 

Battery Support Function 

ONLY 

£ 

679 

12V BEST 

SELLER 

700A 

CRANKING 

RATE 

TWO YEAR 

WARRANTY 

LIGHTWEIGHT 

ONLY 5KG 

BATTERYLESS 

• Battery type selection 

• 4 charging levels 

• Charging timer 

• Automatic battery maintainer 

• SAFE START - Vehicle 

electronics protection 

• AUTO BOOST START - 

One person operation 

• SUPPORT FUNCTION - 

Battery support 

feature, maintains 

vehicle voltage of 13.5v 

(50A) for battery 

replacement and vehicle 

programming (05548) 

INTELLIGENT 

CHARGING 

CHARGING 

TIMER 

SIP 2513 

12V PROFESSIONAL 

BOOSTER 

05548 

• 12v charge voltage, 22Ah battery capacity 

• 2500A boost peak, 850A max. cranking rate 

• Portable, lightweight, and extremely compact 

• 12v DC output socket for smaller devices 

• 12 month maintained battery warranty 

• LED indicators on the control panel 

• Complete with mains fast charger 

• Built-in reverse polarity protection 


ONLY 

£ 

269 


• 2A to 150A flash program current 

• 150A (12v) charger voltage/current 

• 2v to 30v flash program 

voltage range 

• 10 to 1200Ah maximum 

battery capacity 

• Protects ECUs & modules 

during battery changes 

• Multi-step charging and built 

-in recondition mode 

• Designed for both internal 

and external batteries 

• Ideal for ECU flashing and 

software updates 

• Suitable for all major battery types 


ONLY 

£ 

749 

850A 

CRANKING 

RATE 

SWISS 

MADE 

4 CHARGE 

LEVELS 

SIP 150A BATTERY SUPPORT UNIT 

& CHARGER 

SWISS 

MADE 

MADE IN 

ITALY 

LED 

INDICATORS 

HUGE 150A 

RATED CURRENT 

AER SERVICE ELEMAX MOBILE 

EXHAUST GAS EXTRACTOR 

Designed for applications where extraction of 

exhaust gases in enclosed environments is 

required. 

The exhaust gas is extracted at source and 

expelled through the discharge hose. 

Accessories are available to enable it to be 

versatile to extract from a wide range of 

motorcycle, cars, vans and truck workshops. 

The powder-coated trolley is fitted with centrifugal 

fan, with the extraction nozzle bolted directly to it. 

The motor can move vertically and is assisted with 

a gas struct for support and ease of movement. 

AER SERVICE WALL MOUNTED 

EXHAUST GAS EXTRACTORS 

Self-install Gas Extraction System for temperatures 

up to 90ºC. 

Ideal for smaller workshops with space restrictions. 

Easy to use with large area coverage. 

Heavy-duty centrifugal fan with reinforced impeller 

for performance and durability. 

Low energy consumption and low sound 

impact. 

Easy to install, direct to atmosphere 

discharge. 

HY05-00001 

BGNT RUBBER INTAKE 

• Ø 100 - 140mm with membrane top (Cars)* 

PART NO: HY05-00001 

ONLY 

£ 

109 

PART NO 05822 05835 

MODEL 

APN1 Wall Mounted 

Single Hose (7.5m) 

APN2 Wall Mounted 

Twin Hose (10m) 

INPUT SUPPLY 400v 3 phase 400v 3 phase 

MOTOR 1.5HP (1.1kW) 1.8HP (1.1kW) 

AIR FLOW 700m 3 /hr 1400m 3 /hr 

HOSE 

SUPPLIED WITH 

PRICE 

TGA Anti-Crush 

(100mm Ø) 7.5m length 

Wall-mountable hose tidy 

BGN 100mm rubber 

extraction nozzle 

ONLY 

£ 

999 

2x TGA Anti-Crush 

(100mm Ø) 10m length 

2x Wall-mountable hose tidies 

2x BGN 100mm rubber 

extraction nozzles 

ONLY 

£ 

1,649 

PART NO 05820 

05822 

MODEL 

INPUT SUPPLY 

MOTOR 

AIR FLOW 

HOSE 

MOTOR TRAVEL 

PRICE 

HY05-00003 

BGNP2 RUBBER INTAKE 

• Ø 100 - 140mm with clamp (Cars)* 

PART NO: HY05-00003 

ONLY 

£ 

209 

ELEMAX Mobile 

Exhaust Gas Extractor 

230v (13A) 

1.5HP (1.1kW) 

2000m 3 /hr 

T12K Discharge 

(100mm Ø) 7.5m length 

400mm 

ONLY 

£ 

899 

05820 

MADE IN 

ITALY 

MADE IN 

ITALY 

05835 

* Additional discharge ducting / hose required. * Additional discharge ducting / hose required. 

Dingbro Ltd 


51



Draper 

Draper 

D20 20V WORKSHOP KIT 

(4 PIECE) (+1 X 3AH BATTERIES, 1 X 4AH 

BATTERY, CHARGER AND BAG) 

Frequency: Draper D20 workshop kit. The kit contains essential tools for 

everyday workshop tasks. Supplied with a brushless combi drill, brushless 

impact wrench, brushless 115mm grinder, D20 Flexi inspection lamp, 3.0Ah 

battery and 4.0Ah battery, charger, plastic storage caseand a tin of ten 

metal cutting discs. All stored in a 440mm hard bottom tool bag for easy 

transportation and storage. 

D20 20V BRUSHLESS ½ 

” MID-TORQUE IMPACT WRENCH 

(400NM) WITH 2 X 4AH BATTERIES & 

2.4A FAST CHARGER 

Features: Part of the D20 series, Brushless motor, Supplied 

with 2 x 4.0Ah batteries, Supplied with 2.4A charger which 

fully charges a 4.0Ah battery in 110 mins, 5 torque pre-sets 

100N, 150N, 200N, 300N, 400N, Super bright LED work light, 

Belt clip, Protective bump cover 

• D20 multi-tool battery system 

• Brushless technology 

• 2 Ã— 4.0Ah 20V Li-ion batteries 

• D20 2.4A fast battery charger 

• 5 Electronic torque settings 

D20 20V PRESSURE WASHER KIT WITH 

2AH BATTERY & CHARGER 

Features: Part of the D20 series, Portable pressure washer, Fully 

remote, no need for mains water supply operate from bucket 

or similar, Supplied with 6M self priming hose, soap bottle, 

watering lance and extension lance, Supplied with 2Ah battery 

and charger 

• Portable pressure washer 

• Fully remote, no need for mains water supply operate from 

bucket or similar 

• Supplied with 6M self priming hose, soap bottle, watering 

lance and extension lance 

• Supplied with 2Ah battery and charger 

XP20 20V CORDLESS GRINDER & ½” IMPACT WRENCH KIT 

A Draper XP20 bundle including a 1/2” impact wrench with an impressive 1000Nm of power 

and a 115mm angle grinder, 2 x 4.0Ah batteries and a fast charger. A great kit for a 

host of activities, especially useful in the automotive and construction industries. Both 

tools feature the innovative XP20 brushless motor and intelligent SCB technology. 

The impact wrench and angle grinder have a compact design for easier use in hard to 

access areas and include all-metal gearboxes for increased tool life and performance, 

with the added benefit of both the impact wrench and the grinder being supplied with a 

3-year warranty for total peace of mind. 

• A Draper XP20 bundle including a 1/2” impact wrench and a 115mm angle grinder, 2 

x 4.0Ah batteries and a fast charger 

24047 

• A great kit for a host of activities, especially useful in the automotive 

and construction industries 

• Featuring the innovative XP20 brushless motor and 

intelligent SCB technology 

• Compact design for easier use in hard to access areas 

• All-metal gearboxes for increased tool life and performance 

ONLY 

£ 

399 

COMBINATION SPANNER SET 

(25 PIECE) 

Combination Spanner Set offering 25 different sized ends ranging 

from 6-32mm. All forged from chrome vanadium steel that has 

been hardened, tempered and fully polish chrome plated for 

added corrosion protection. 

Spec 

• Draper HI-TORQÂ ® ring end offset at 15 degree 

• Jaw offset at 15Â° 

• Fully polished and Chrome plated 

• Supplied in a storage pouch 

NEW 

90470 

ONLY 

£ 

290 

Spec 

• AC Current: 60uA/600uA/6000uA/60mA/600mA/20A 

• AC Voltage: 600mV/6V/60V/600V/750V 

• Automatic Power Off: Yes 

• Battery: 6F22 9V 

• Capacitance: 9.999nF/99.99nF/999.9nF/9.999µF 

• /99.99µF/999.9µF/9.999mF/99.99mF 

• DC Current: 60uA/600uA/6000uA/60mA/600mA/20A 

• DC Voltage: 600mV/6V/60V/600V/0.1V/1000V 

• Dimensions: 190mm x 90mm x 50mm 

• Diode on/off Test: Yes 

• Dwell: N/A 

• Frequency: 9.999Hz/99.99Hz/999.9Hz/ 

• 9.999kHz/99.99kHz/999.9kHz/9.999MHz 

• Resistance (Ohms): 6000½/6k½/60k½/600k½/6M½/60M½ 

• Symbol Unit Data Hold: Yes 

• TACH: N/A 

• Temperature Range: -20¡C - 1000¡C/-4¡F - 1832¡F 

• Weight: 380g (approx) 

D20 20V 

FAST BATTERY CHARGER 

Features: Part of the D20 series, 1.8M cable, Suitable for 2.0Ah, 3.0Ah, 

4.0Ah and 5.0Ah D20 batteries 

• 1.8M cable 

• Suitable for 2Ah, 3Ah, 4Ah and 5Ah D20 batteries 

55913 

ONLY 

£ 

25 

D20 20V LITHIUM BATTERY (3.0AH) 

Features: Part of the D20 series, 20V 3.0Ah, Lithium-Ion, 

Charge indicators lights 

• 20V 3.0Ah 

• Lithium-Ion 

• Charge indicator lights 


Features: Part of the D20 series, 20V 4.0Ah, Lithium - Ion, 


• 20V 4.0Ah 



Spec 

• Battery: D20 20V Li-ion 

• Batteries Amperage: 4Ah 



Features: Part of the D20 series, 20V 5.0Ah, Lithium-Ion, 


• 20V 5.0Ah 



Spec 




Spec 




00649 

ONLY 

£ 

38 

55898 

ONLY 

£ 

48 

55907 

ONLY 

£ 

66 

99251 

ONLY 

£ 

180 

Spec 


• Impact Rate: 0-3300bpm 

• No-load speed: 0-2200rpm 

• Max Torque: 400Nm 

• Variable speed: 100N, 150N, 200N, 300N, 400N 

• Square Drive: 1/2” 

• Batteries Per Item: 2 x 4Ah 

• Charger Type: 2.4A 

• Supplied in Case: Yes 

• Weight (bare tool): 1.5kg 

• Dimensions: 460 x 270 x 345mm 

• Weight: 10kg 

D20 20V 

HEAT GUN BARE 

Features: Part of the D20 series, LED worklight, Safety 

switch, Hanging hook/body stand, Supplied with glass 

protector nozzle, reflector hook 

nozzle and concentrator nozzle, 

Batteries and chargers are 

available separately 

• LED worklight 

• Safety switch 

• Hanging hook/body stand 

• Supplied with glass protector 

nozzle, 

reflector hook nozzle and 

concentrator nozzle 

• 5 seconds heat up time 

Spec 


• Temperature: 550¼C 

• Airflow volume: 200L/min 

• Batteries Per Item: Sold separately 

• Charger Type: Sold separately 

• Supplied in Case: No 


GRAVITY/SUCTION 

OIL DRAINER (90L) 

Expert Quality, air operated waste oil drainer with 

gravity fed reservoir. Fitted with a suction pump for 

the extraction of oil via the dipstick and a 400mm, 10L 

collection bowl. Discharge is by air pressure. Fitted 

with safety valve, 18L steel telescopic collection pan, oil 

reservoir level indicator and small working tray. Heavy 

duty castors for easier manoeuvrability around the 

workshop with chrome plated pull - along handle. 

• Expert Quality 

• Air operated waste oil drainer 

with gravity fed reservoir 

• Fitted with a suction pump 

for the extraction of oil via the 

dipstick and a 400mm, 10L 

collection bowl 

• Discharge is by air pressure 

• Fitted with safety valve, 18L 

steel telescopic collection pan, 

oil reservoir level indicator and 

small working tray 

66241 

ONLY 

£ 

180 

55796 

ONLY 

£ 

42 

Spec 


• Pressure: 0-16 Bar 

• Max Flow Rate: 120L/H 

• Suction Height: 5ft (self priming) 

• Batteries Per Item: 1 x 2.0Ah 

• Charger Type: 4A 



97533 

ONLY 

£ 

100 

D20 20V BRUSHLESS COMBI DRILL BARE 

Features: Part of the D20 series, Brushless motor, 23 torque 

settings, Metal keyless chuck, Variable speed with electronic brake, 

LED worklight, Adjustable side handle and depth rod, Batteries and 

chargers are available separately 

• D20 multi-tool battery system. 

• Brushless technology. 

• 2 Speed gearbox. 

• LED worklight. 

Spec 


• Impact Rate: 29700bpm 

• No load speed: 0-500rpm 

• Max Torque: 60Nm 

• Chuck capacity: 13mm (1/2”) 



• Drilling capacity wood: 35mm 

• Drilling capacity steel: 13mm 



55338 

ONLY 

£ 

60 

D20 20V 

BRUSHLESS GRINDER BARE 

Features: Part of the D20 series, Brushless motor, Spindle lock, 

3 position side handle, M14 thread, Batteries and chargers are 

available separately 

• Brushless motor 

• Spindle lock 

• 3 position side handle 

• M14 thread 

• Batteries and chargers are available separately 

Spec 


• No Load Speed: 8500rpm 

• Disc Diameter: 115 mm 

• Disc Bore Size: 22.2 mm 





55478 

ONLY 

£ 

58 

230V PLASMA CUTTER KIT (25A) 

Features: Microprocessor controlled inverter technology Suitable 

for cutting any electrically conductive material Input current 13A 

Thermal overload protection Supplied with a plasma torch, earth 

lead and clamp, air regulator, air hose, chipping hammer with 

brush and face mask 

• Microprocessor controlled inverter technology 

• Suitable for cutting any electrically conductive material 

• Input current 13A 

• Thermal overload protection 

• Supplied with cutting torch, 2M earth clamp, chipping 

hammer/brush, mask 

Spec 

• Cutting current range: 10-25A 

• Input current: 13A 

• Duty cycle: 25% - 25A 

• Cutting range: 8mm (mild steel) 

• Clean cut: 5mm 

• Severance cut: 8mm 

• Air Required: 8.8 cfm 

• Dimensions: 460 x 270 x 345mm 


92454 

ONLY 

£ 

255 

VERTICAL TRANSMISSION JACK 

(600KG) 

Expert Quality, hydraulic vertical transmission jack with a 

telescopic ram. The jack is fitted with a twin-piston ‘Quick Lift’ 

facility and a safety overload valve for added user protection. 

Operated via a foot pedal for hands - free operation fitted with 

an anti - slip rubber cover. The hardwearing Nylon wheels 

help prevent damage to garage floors delivering a quieter and 

smoother operation. The extra - 

large castors and side - mounted 

handles aid positioning and 

increase manoeuvrability around 

the workshop or garage. The 

reversible saddle can accept a wide 

variety of gearboxes/components. 

• Expert Quality 

• Hydraulic vertical transmission 

jack with a telescopic ram 

• Fitted with a twin-piston ‘Quick Lift’ 

facility and a safety overload valve 

for added user protection 

• Operated via a foot pedal for hands 

- free operation 

• Hardwearing Nylon wheels help 

prevent damage to garage floors 

delivering a quieter and smoother 

operation 

Spec 

NEW 

• Base Size: 640 x 650 mm 

• Capacity: 0.6 Tonne (600kg) 

• Castor Diameter: 75mm 

• Max Height: 1985mm 

• Min Height: 1175mm 

• Saddle Type: Fixed 


70668 

ONLY 

£ 

180 

NEW 

200MM ENGINEER’S BENCH VICE 

Strong and durable engineerâ€s bench vice. The body of the vice 

is made from high quality cast iron with a steel screw and tommy 

bar handle. Hardened carbon steel interchangeable jaws. Suitable 

for workshop, automotive and engineering use. Carton packed. 

• Jaw width is 200mm 

• Jaw depth is 205mm 

• Weight 26.5kg 

93058 

ONLY 

£ 

100 

TYRE BEAD SEATER 

Fully certified 19L tank with liquid - filled gauge for increased 

accuracy and prolonged service life. Safety valve automatically 

activates when the air pressure reaches the maximum operating 

pressure. Pumps air into the tyre void forcing the bead to Seat 

against the rim of the wheel providing an easy way to Seat 

tubeless tyre beads. Suitable for use on cars, commercials, 

agricultural and ATV tyres. Fitted with a 1/4” BSP male coupler. 

• Liquid filled gauge for increased accuracy & prolonged 

service life. 

• Pressure relief valve. 

NEW 

80000 

ONLY 

£ 

90 

MASTER HYBRID/ELECTRIC VEHICLE 

TOOL KITS (3/8” SQ. DR) 

With the ever-increasing rise in electric/hybrid vehicles, 

technicians have to adapt to new working practices. To safely 

adhere to best working practices our comprehensive electric/ 

hybrid vehicle service kit provides equipment to enable vehicle 

technicians to work on electric/hybrid vehicles safely. 

Spec 

• Adhere to best safe working practices 

• Comprehensive electric/hybrid vehicle service kit 

• Containing tools and equipment to safely enable vehicle 

technicians to work on electric/hybrid vehicles 

NEW 

99710 

ONLY 

£ 

500 

NEW 

97918 

ONLY 

£ 

35 

DIGITAL MULTIMETER 

(AUTO & MANUAL RANGING) 

Expert Quality, auto - ranging CAT IV multimeter. Equipped 

with a high - performance MCU processor for more accurate 

measurements. Capable of DC voltage, AC voltage sine RMS, 

DC current, AC current sine RMS, resistance, capacitance, 

frequency, duty ratio, diode on/off test, symbol unit data hold 

and automatic power - off functions. Fitted with a large LCD 

backlit display screen, an NCV (Non - contact voltage) sensor and 

inspection light. An essential tool for electrical and industrial 

applications, especially useful for electricians, maintenance 

engineers, construction workers and electric vehicle technicians 

working on modern hybrid and electric vehicles. Supplied with 9V 

battery and a carry case. 

• Large LCD backlit display screen 

• Supplied with probes, battery, bump 

cover and storage case 

• Auto-ranging CAT IV multimeter 

• High-performance MCU processor 

• Capable of DC voltage, AC voltage sine 

RMS, DC current, AC current sine RMS, 

resistance, capacitance, frequency, duty 

ratio, diode on/off test, symbol unit data 

hold and automatic power-off functions 

92433 

ONLY 

£ 

47 

ELECTRICAL EXCLUSION KIT 

An electrical exclusion kit for helping to safely isolate an area 

where electrical appliances or infrastructure is being worked on. 

Suitable for a host of safety environments including when vehicle 

technicians are working on electric/hybrid vehicle and when 

electricians are on building sites. 

Spec 

• Adhere to best safe working practices 

• Helps to safely isolate areas where electrical appliances or 

infrastructure is being worked on 

• Suitable for a host of safety environments including when 

vehicle technicians are working on electric/hybrid vehicle and 

when electricians are on building sites 

99714 

ONLY 

£ 

80 

NEW 

Dingbro Ltd 


53



Sealey Tools 

Sealey Tools 

2TONNE LOW ENTRY 

TROLLEY JACKS 

• Min./Max. Saddle Height: 85/385mm. Chassis Length: 563mm. 

• Heavy-duty chassis with strengthening flanges along the top edge for extra 

torsional rigidity under load. 

• Profiled lifting arm allows low clearance height of 

just 85mm making these units suitable for sports 

and custom cars. 

• Fitted with heavy-duty one-piece hydraulic unit with 

pump-through action preventing handle locking at 

maximum ram extension. 

42PC 3/8" & 1/2"SQ DRIVE 

TRX-STAR*/HEX/SPLINE BIT SET 

• Hardened (58-62 HRC) and tempered for added strength. 

• Contents: TRX-Star* Bits; T20, T25, T30, T40, T45, T50, T55, T60 

(1 each 30 & 75mm), Hex Bits; 4, 5, 6, 7, 8, 10, 12mm (1 each 30 & 

75mm), Spline Bits; M5, M6, M8, M10, M12 (1 each 30 & 75mm), 

Drive Adaptors; 3/8"Sq x 10mm Hex, 1/2"Sq x 10mm Hex. 

• Model No. AK21942P 

ONLY 


2L MEASURING FUNNEL 

WITH LID AND BASE 

• Graduations that can be 

used for transferring a 

measured quantity of fluid 

without any spills 

or splashes. 

• Simple press of a lever 

dispenses liquid through 

a built-in metal sieve to 

ensure contaminant free 

transfer. 

• Replace funnel back into 

base in between use, no 

need to pour unwanted 

liquids back into original 

storage container. 

• Model No. MF2/BC 


BRAKE PIPE BENDING 

TOOL 

• Dual stepped sections allow pairing 

of pipes for correct curvature for 

uniformed alignment to vehicle. 

• Suitable for 3/16"(4.76mm) cupronickel, 

copper and steel pipe. 

• Diameter: 21, 31.5, 

46.5, 61.5, 76.5mm. 

• Model No. VS5057 


ONLY 

£ 

25 

ONLY 

£ 

33 

£ 

30 

Model No. 

18L MANUAL VACUUM OIL 

& FLUID EXTRACTOR 

• Suitable for the extraction of all types of 

engine, transmission and lubricating oil 

from cars, motorcycles, marine engines, 

stationary engines and industrial 

machinery. 

• Supplied with Ø5.8 and Ø6.7mm suction 

probes and Ø9.8mm extension tube. 

• Uses probes to extract engine oil through 

the dipstick tube. 

• Unit can be tipped past 90° for 

easier emptying. 

• Model No. TP6908 


PNEUMATIC BRAKE 

BLEEDER 

• Pressure range makes 

unit suitable for use with 

ABS systems. 

• Two drainage method 

options allow you to drain 

brake fluid via the brake 

caliper with the bottle 

option for replenishing, 

or brake reservoir 

pressurising for full 

brake bleed. 



Colour 

TYRE INFLATOR WITH 0.5M 

HOSE & TWIN PUSH-ON 

CONNECTOR 

• Manufactured to comply with EN 12645. 

• Aluminium body with rubber bumper. 

• Linear pressure scale, dual calibrated in psi 

and bar, with parallax correction. 

• 0.5m Flexible hose fitted with 240mm, twin 

push-on air connector. 

• Range: 0-9.5bar(0-138psi). 

• Model No. 

SA371 


List 

Price 

OUR PRICE 

1020LEB Blue £64.95 

£44.95 

1020LEHV Hi-Vis Green £64.95 

£44.95 

1020LEO Orange £64.95 

£44.95 

ONLY 

£ 

140 

ONLY 

£ 

90 

ONLY 

£ 

58 

9 DRAWER 690MM TOWER 

CABINET WITH SOFT CLOSE 

DRAWERS & POWER STRIP 

• Heavy-duty 45mm ball bearing drawer slide 

provide superior performance, suitable for 

heavier loads. 

• Full height rear locking mechanism, locks 

smooth running soft close drawers in place. 

• Fitted with four Ø125mm PP wheels with 

black chrome effect alloys, two castors with 

quick release anti-rotation toe locks and two 

fixed wheels. 

• Each drawer features stylish black anodized 

heavy-duty drawer pulls and 

pre-cutnon-slip liners. 

• Model No. AP2709BE 


12 DRAWER TOOL 

CHEST COMBINATION 

WITH POWER BAR 

Package includes: 

• AP3606BE - 6 Drawer 915mm 

Rollcab with Soft Close 

Drawers 

• AP3607BE - 6 Drawer 910mm 

Topchest Soft Close Drawers 

& Power Strip 

• Model No. AP36BESTACK 

• List Price £1,379.90 

ONLY 

£ 

740 

12V CORDLESS 

RECIPROCATING 

SAW - 2 BATTERIES 

Package includes: 

• CP1208 - 12V 

Cordless Reciprocating 

Saw - Body Only 

• CP1200BP - 12V 1.5Ah 

Lithium-ion Power Tool Battery 

(x2) 

• CP1200MC - 12V Lithium-ion 

Battery Charger 

• CP1200CB - Canvas Tool 

Storage Bag for SV12 Series 

Model No. CP1208KIT 


ONLY 

£ 

500 

ONLY 

£ 

80 

12V Ø76MM 

ANGLE GRINDER BODY ONLY 

• Compact, lightweight cordless mini angle 

grinder. 

• Comfortable composite housing with soft 

grip to reduce vibration. 

• Brushless motor allows for a longer lasting 

tool requiring less maintenance. 

• Spindle lock for easy disc changes. 

• Built-in battery charge level indicator. 

• Cutting disc not included. 

• Model No. CP1208KIT 


ONLY 

£ 

60 

420/60A 12/24V 

STARTER/CHARGER 

• Max. Charge: 60A (40A EN). 

• Max. Start: 420A (280A EN). 

• 22Amps Max. Input (start). 

• Battery Range: 30-700Ah. 

• Polarity protected. 

• Heavy-duty starter/charger for professional 

garages, workshops and bodyshops. 

• Caters for all requirements from cars right up 

to light commercial vehicles. 

• Large wheels for easy mobility and features 

analogue ammeter and switchable charge 

circuitry for accurate 

charge control. 

• Model No. START420 

ADBLUE ® STATION KIT 

INSPECTION LAMP 

Model No. RS1 Model No. RS102 

Model No. Cold Cranking Amps Peak Amps Cable & Clamp Length List Price OUR PRICE 


RS1 300A 1000A 0.5m £159.95 £ 

ONLY 

105 

£ RS102 600A 1600A 1m £239.95 £ 

150 

170 

16A 12/24V BATTERY CHARGER 

63 SMD LED 1000LM UNDER-BONNET 

CORDLESS RECHARGEABLE LAMP 

• Steel case with a sturdy carry handle, 

this single phase charger features good 

ventilation to help maintain low transformer 

temperatures. 

• A large ammeter displays rate of charge 

and a dash-mounted fuse provides polarity 

protection in the event of the clips being 

connected incorrectly. 

• Suitable for regular and low maintenance 

• Min/Max Bonnet Width: 1200/1800mm. 

batteries (20-180Ah). 

ONLY 

• Battery: Li-ion 3.7V - 4.4Ah. 

ONLY 

• Model No. CHARGE112 

£ • Model No. LED138 


82 

£ 


68 

REFRACTOMETER ANTIFREEZE/ RECHARGEABLE FLOODLIGHT/ 

8W COB + 1W LED 

BATTERY FLUID/SCREENWASH/ INSPECTION LAMP DOCKING 

RECHARGEABLE 

• Accurately measures the strength of battery 

fluid, screenwash, antifreeze and AdBlue ® by 

measuring the refractive index of light passing 

through the mixture. 

• Suitable for synthetic antifreeze mixtures including 

long life OAT (Organic Acid Technology), G13 and 

aqueous/urea content of AdBlue ® . 

• Supplied with pipette and storage case. 



ONLY 

MECHANIC’S UTILITY SEAT 

& TOOLBOXES 

Model No. 

SCR18O 

£ 

55 

• Two folding side trays. 

• Twin can capacity drinks holder and screwdriver storage rack on 

the rear. 

• Four Ø60mm oil resistant swivel castors. 

• Thick vinyl padded seat. 

• Overall Size (W x D x H): 670 x 360 x 410mm. 

• Max. Load: 136kg. 

• Docking station kit includes 2 x LED1801 and charging station. 

• Each inspection lamp has 12 x SMD LEDs (side) 

+ 1 x SMD LED (top) producing up to 500 lumens. 

• When docked, lights can be charged or used as a floodlight. 

• Each inspection lamp can extend and is able to rotate 180°. 

• Two charging points with individual LED charging level indicators. 

• Includes 5V-2A mains adaptor and 

1m USB charging cable. 

• Model No. LED1801K 


Model No. 

SCR18Y 

ROADSTART ® EMERGENCY 

JUMP STARTERS 

• Units are fitted with 12V power 

socket, that will accept any 

12V device fitted with a vehicle 

accessory socket. 

• LED Battery condition, and 

charge indicators. 

• Supplied with mains charger 

and double plug cable for incar 

charging. 

Model No. 

SCR18G 

ONLY 

£ 

90 

Model No. 

SCR18R 

Model No. Colour List Price OUR PRICE 

SCR18O Orange £109.95 £ 

75 

SCR18Y Yellow £109.95 £ 

75 

SCR18G Green £109.95 £ 

75 

SCR18R Red £109.95 £ 

75 

• Robust aluminium design with built-in 

spring loaded telescopic mounting brackets. 

• Both brackets can rotate 360° individually making it easy to direct the light 

where required. 

• 63 SMD LEDs have two options on light settings; full - 1000lm, 

half - 500lm. 

• Includes battery level indicator, mains charger and USB lead. 

• Smooth 90° flex with additional 

360° twist function. 

• Super bright 8W COB LED 

provides up to 1000 lumens output 

with 120° spread of light. 

• Additional high power 1W LED 

directional torch. 

• Swivel hanging hook and rubber 

covered magnet on the base. 

• Two 2.6Ah Lithium-ion batteries 

for longer life. 

• Operating Time Side 

(High/Low)/Top: (2/4)/16hr. ONLY 

• Model No. LED1001 


£ 

28 

2W COB LED RECHARGEABLE HEAD 

TORCHES WITH AUTO-SENSOR 

• New design 360° multi-function COB LED rechargeable head 

torches. 

• Headband can also be used as a wristband. 

• When the band is removed, the work light can be attached to 

objects via the integral clip. 

• One button includes five different lighting options. 

• Holding the button enables auto-sensor function to switch on/ 

off just by waving hand in front. 

• Powered by 3.7V 0.5Ah Li-Poly battery. 

Model No. Colour List Price OUR PRICE 

LED360HTR Red £14.95 £ 

11 

LED360HTG Green £14.95 £ 

11 

LED360HT Black £14.95 £ 

11 

*Please refer to www.sealey.co.uk/guarantee for more information on guarantees. Specifications and descriptions on this promotion are given in good faith but may change without notice and do not form any part of a sale contract, E & OE. 

*TRX-STAR, TRX-TS and TRX-P tools are suitable for driving TORX ® and TORX PLUS ® fasteners respectively. TORX ® and TORX PLUS ® are registered trademarks of Acument Intellectual Properties, LLC. 

Dingbro Ltd 


55



Laser Tools: Electrical 

Laser Tools: Bodywork 

ASSORTED WIRING HARNESS KIT 

RENAULT - 12PC 

ASSORTED CONNECTOR KIT 

CITROËN/PEUGEOT - 24PC 

ASSORTED CONNECTOR KIT 

VOLVO - 24PC 

ASSORTED TRIM CLIPS 

SKODA OCTAVIA - 420PC 


SKODA FABIA - 420PC 


VW TIGUAN - 300PC 

Sensors can be used in any area of the vehicle. Mainly used in 

the engine bay to protect circuits and important sensors for the 

engine management system. 

Popular assortment of Renault electrical connector harnesses. 

• Contains: temperature sensor connector (37578) x 2, oxygen 

sensor connector (37579) x 2, heater resistor connector (37580) 

x 2, heater resistor connector (37581) x 2, 

crankshaft sensor connector (37582) x2, 

fuel pump connector (37583) x 2. 

• Connectors come complete with 

200mm cable. 

• Replacement blister packs available. 

37616 

ONLY 

£ 

50 

ASSORTED ELECTRICAL CONNECTORS 

VW 1.5 SERIES - 47PC 

Assortments contain both the male and female connectors 

along with the non-insulated terminals and seals to make the 

waterproof connection and seal. Sensors can be used in any area 

of the vehicle. Mainly used in the engine bay to protect circuits and 

important sensors for the engine management system. Suitable 

for use with Laser Tools part numbers: 7293, 7002, 6547, 3932, 

3984 & 4027. 

Popular assortment of VW electrical sensor connectors. 

• Contains: 1 pin connectors male & female (5), 2 pin connectors 

male & female (5), 3 pin connectors male & female (4), 4 pin 

connectors male & female (4), 6 pin connectors female (3), 8 pin 

connectors female (2) & 14 pin connectors female (2). 

• Complete with terminals & seals to suit. 

Popular assortment of Citroën/Peugeot electrical connectors. 

• Contains: 2 x temperature sensor connectors (37584), 2 x 

ignition coil connectors (37586), 2 x fog lamp connectors 

(37587), 2 x fuel injector connectors (37588), 2 x MAP sensor 

connectors (37589), 2 x multi-purpose 2 pin connectors 

(37592), 2 x multi-purpose 3 pin connectors (37593), 2 x multipurpose 

4 pin connectors (37594), 2 x 

multi-purpose 6 pin connectors (37595), 

2 x oxygen sensor connectors (37597), 2 x 

oxygen sensor connectors (37598), 2 x air 

pressure sensor connectors (37599). 

• Complete with related terminals & 

seals to fit each connector. 

• Replacement blister packs 

available. 

37617 

ONLY 

£ 

45 




• Contains: 2 pin connectors male & female (4), 3 pin connectors 

male & female (3), 4 pin connectors male & female (2), 6 pin 

connectors female (2), 8 pin connector male & female (1), 10 

pin connector male & female (1). 


Popular assortment of Volvo electrical connectors. 

• Contains: multi-purpose 2 pin connector (37601) x 2, multipurpose 

2 pin connector (37603) x 2, multi-purpose 2 pin 

connector (37605) x 2, multi-purpose 2 pin connector (37606) 

x 2, camshaft sensor connector (37607) x 2, camshaft sensor 

connector (37608) x 2, camshaft sensor connector (37430) x 

2, fuel pressure connector (37609) x 2, multi-purpose socket 

housing (37610) x 2, headlight H7 

bulb connector (37612) x 2, air 

flow sensor connector (37614) x 2, 

power steering pump connector 

(37615) x 2. 

• Complete with related terminals & 

seals to fit each connector. 

• Replacement blister packs 

available. 

37618 

ONLY 

£ 

45 




• Contains: 2 pin connectors male black (8), 2 pin connectors 

female black (8). 


Trim clip fixings are automotive fasteners manufactured to be 

original manufacturer replacement trim clips suitable for many 

vehicle manufacturers and applications. 

Kits have been designed by Connect Workshop Consumables and 

are unique to our ever expanding range. 

Assorted box of popular fixings to suit Skoda Octavia. 

Skoda Octavia's sit in 'What Cars' European top selling 25 cars. 

• Kit contains: trim locking nuts, moulding clips, weatherstrip 

clips, panel clips, metal fixings, drive rivets. 

• Assortment contains 12 different clips. 

• Full range of replacement 

packs available. 

35987 

ONLY 

£ 

60 


VW PASSAT - 240PC 

Assorted box of popular fixings to suit Volkswagen Passat. 

Volkswagen Passat's sit in 'What Cars' European top selling 25 

cars. 

• Kit contains: fir tree fixings, panel clips, screw rivets, moulding 

clips, push retainers. 


• Full range of replacement 


Assorted box of popular fixings to suit Skoda Fabia. 

Skoda Fabia's sit in 'What Cars' European top selling 25 cars. 

• Kit contains: trim locking nuts, fir tree fixings, weatherstrip 

clip, drive rivets, moulding clip & panel clip. 


• Full range of replacement packs available. 

35988 

ONLY 

£ 

60 


VW POLO - 381PC 

Assorted box of popular fixings to suit Volkswagen Polo. 

Volkswagen Polo's sit in 'What Cars' European top selling 25 cars. 


clips, push retainers, weatherstrip & button clips. 



Assorted box of popular fixings to suit Volkswagen Tiguan. 

Volkswagen Tiguan's sit in 'What Cars' European top selling 25 

cars. 

• Kit contains: trim locking nuts, drive rivets, screw rivets, 

moulding clips, metal fixings. 



35989 

ONLY 

£ 

55 


AVW GOLF - 251PC 

Assorted box of popular fixings to suit Volkswagen Golf. 

Volkswagen Golf's sit in 'What Cars' European top selling 25 cars. 


clips, push retainers & button clips. 



35990 

35991 

35992 

37396 

ONLY 

£ 

63 

CONNECTOR & TERMINAL REMOVAL KIT 

VAG VEHICLES - 3PC 

• For use on MAF sensor, coil pack, headlight, fog light, level 

sensor and most terminal blocks on VAG vehicles. 

• Designed for use on most push and pull style connectors. 

• Also for releasing terminals junior and micro connectors. 

• Ideal for use with the following Connect Consumable products: 

Part Nos. 37361-37395 or Assorted Boxes Part Nos. 37396- 

37399. 

37397 

ONLY 

£ 

43 

CONNECTOR REMOVAL TOOL 

LONG SERIES - FOR VAG/PORSCHE 

• Long series version of Laser 6547 with offset head to give 

better access to difficult to reach connections. 

• Fits directly on to the push and pull connectors and opens the 

locking tabs as pressure is applied. 

• Applications include MAF sensors, coil packs, MAP sensors, 

CPS sensors and light connectors. 

• Soft grip T-handle. 

• 20mm offset head, 

160mm long. 

37398 

ONLY 

£ 

25 

RECHARGEABLE HEAT SHRINK TOOL SET 

• Rechargeable heat shrinking tool with LEDs, USB lead and 

stand. 

• Assorted coloured tubing; diameters: 2mm, 3.5mm, 5mm, 

7mm, 8mm & 9mm. 

• Operating temperature range: -55°C to +125°C. 

• Shrinkage ratio: 2:1, very flexible, highly flame retardant and 

resistant to common fluids & solvents. 

• Tubing manufactured from general purpose polyolefin tubing. 

RoHS compliant. 

ONLY 

£ 

50 

ASSORTED METAL SCREW TRIM 

FASTENERS 

135PC 

Metal bodyshop fixings are automotive fasteners manufactured 

to be original manufacturer replacement trim clips suitable for 

many vehicle manufacturers and applications. 

Kits have been designed by Connect Workshop Consumables and 

are unique to our ever expanding range. 

Assorted box of popular fixings. 

• Heavy duty body trim clip fasteners. 

• Kit covers Ford, Vauxhall/Opel & VAG applications. 

• Full range of top up 


ONLY 

£ 

60 

ASSORTED METAL BODY SCREW TRIM 

FASTENERS 

100PC 


• Heavy duty body fixings, various applications. 

• Kit covers Ford, Vauxhall/Opel & Chrysler applications. 

• Full range of top up packs available. 

ONLY 

£ 

55 

ASSORTED METAL TRIM NUTS & U NUTS 

245PC 


• Comprehensive range of U nut type body fixings. 

• Kit covers Ford, BMW, Mercedes-Benz, VAG & many more 

applications. 


7293 

7859 

REGISTERED 

EU D E S I G N 

7607 

35994 

35993 

35995 

ONLY 

£ 

25 

ONLY 

£ 

15 

ONLY 

£ 

50 

ONLY 

£ 

40 

ONLY 

£ 

40 

ONLY 

£ 

60 

FLAMELESS HOT AIR BLOWER 

• Instant electronic ignition with a refillable tank and see through 

window. Also stable catalystic heating system. 

• Variable heat/temperature range up to 650°C. Run time 

approximately 20 - 25 minutes (at mid setting). 

• Fuel: 5.5ml butane gas (widely available). Net weight without 

gas 68g. Dimensions 110 x 27 x 85mm. 

• Includes 4, 74mm long heat shrinking tubes: 2 x 4mm dia, 2 x 

5mm dia. 

• Replacement heat shrinking tube rolls available, please see 

Connect Part No. 37113 (5mm dia), 37112 (3.2mm dia). 

ASSORTED BOX OF DUAL WALL HEAT 

SHRINK SLEEVING BLACK/RED - 144PC 

Adhesive lined inner wall seals and protects against moisture 

which protects against corrosion. Creates a waterproof seal. 

Protects and insulates wires and components. 

• Shrink ratio 3 : 1, waterproof, RoHS Compliant. 

• 89mm cut lengths - sizes: 3.2mm, 4.8mm, 6.4mm, 7.9mm, 

9.5mm, 12.7mm, 19.1mm. 

• Material - Polyolefin, max. electrical rating 600V. 

• Shrink temperature starts at 70°C, shrunk totally at 120°C. 

ASSORTED BOX OF HEAT SHRINK 

COLOURED - 250PC 

• Operating temperature -55°C - +125°C. 

• Shrink ratio 2 : 1. 

• 89mm cut lengths - sizes: 2.0mm, 3.0mm, 5.0mm, 7.0mm, 

8.0mm, 10.0mm, 12.0mm in black; 2.0mm, 12.0mm in green; 

3.0mm, 10mm in red; 5.0mm in white; 7.0mm in blue; 8.0mm 

in yellow. 

• Material - Polyolefin, max. electrical rating 600v, RoHS 

compliant. 

• Shrink temperature starts at 70°C, 

shrunk totally at 110°C. 

ASSORTED METAL TRIM RIVETS 

150PC 


• Comprehensive range of metal trim rivets. 

• Kit includes items to cover Ford, Vauxhall/Opel, Mercedes- 

Benz, Nissan, Mazda & Chrysler. 


TRIM & PANEL REMOVAL KIT 

27PC 

A 27 piece trim and panel remover set made from 

composite material to help to prevent damage. 

• Ideal for assisting radio removal and wheel 

weights. 

• Manufactured from composite material. 

• Use on windscreens. 

• Supplied in a 

handy storage 

wallet. 

TRIM CLIP REMOVER 

Part of the Laser range of trim clip removal tools. 

• Robust, tapered design. 

• 172mm long, 15mm wide. 

• 5mm jaw. 

• Dipped shaped handle. 

• Chrome polished finish. 

6848 

37197 

37198 

35996 

6978 

6694 

ONLY 

£ 

17 

ONLY 

£ 

28 

ONLY 

£ 

15 

ONLY 

£ 

50 

ONLY 

£ 

30 

ONLY 

£ 

13 

Dingbro Ltd 


57



Laser Tools: Braking 

Laser Tools: Suspension 

BRAKE/CLUTCH BLEEDER 

12V 

A portable, self contained, pressurised brake bleeder which is 

powered from the vehicle's 12V battery - the output pressure 

is adjustable up to a maximum of 36psi (2.5 bar). Suitable for 

professional workshop use. 

• Stainless Steel case with a reservoir tank that has a 5 litre 

capacity which enables the entire braking system fluid to be 

replaced in one fill without the risk of the reservoir running dry. 

• Supplied with catchment bottle and a syringe to 

remove old fluid and to help set the level. 

• Suitable for both hydraulic brake & clutch systems. 

• Supplied with a 44mm European brake fluid 

reservoir adaptor. Cap kit available, please 

see Laser Part No. 7101. 

5629 

ONLY 

£ 

600 

BRAKE MASTER CYLINDER CAP KIT 

Suitable for most brake pressure brake bleeders. 

• Adaptors cover 90% of current master cylinder reservoirs. Can 

be used with Laser Part No. 5629. 

• Applications include: European, American and Asian vehicles. 

• 2x universal cap assembly for diameters: 47 - 85.5mm & 29 - 

55mm with hooks, chain & bracket. 

• 8 x caps: Nissan bayonet 34.5 - 53.5mm, Euro cap 42 - 57.5mm, 

Chrysler, Jeep 3 point bayonet 43.5 - 49mm cap & blank, GM 

49.5 - 66.5mm, Hyundai, Mitsubishi, Subaru, Ford & Chrysler 

50.7 - 57mm, Honda 56 - 79.5mm, Honda 74 - 93mm. 

• 1x 41mm adaptor with lock clamp for Toyota and Lexus models. 

7101 

ONLY 

£ 

170 

VACUUM/PRESSURE TEST KIT 

This vacuum and pressure pump creates and holds a metered 

vacuum for testing a wide variety of car, van, motorcycle, marine, 

aircraft and agricultural equipment. Can also be used for oneman 

brake bleeding. 

• Vacuum testing applications include: automatic transmission, 

vacuum reservoirs, air conditioning and heating, heater 

cones, brake systems including ABS and conventional, engine 

management systems, emission control systems, fuel systems, 

engine tuning, ignition systems, engine management including 

cylinder heads, valve stem oil seals, piston ring retainers on 

diesel engines, waste gases on turbo chargers. 

• Dual function - vacuum: 0 - 30 in vacuum (0 to -1 bar). 

• Pressure: 0 - 60psi (0 - 4 bar). 

• Simply select the air intake control valve on the pump: Out for 

pressurised systems, In for testing vacuums. 

3752 

ONLY 

£ 

90 

BRAKE FLUID BOILING POINT TESTER 

Performs a boil test on a sample of fluid taken from the vehicle 

system and gives a clear indication of the boiling temperature and 

a clear indication of the serviceability of the fluid. 

• Identifies the boiling point of any brake fluid sample. 

• Powered from the vehicles own battery. 

• Clear accurate digital read out. 

• Accuracy and calibration of the device can be easily serviced by 

testing the boiling point of clean water; if it boils at 100°C, then 

the tester is 100% accurate. 

• Sampling syringe & glass sampling container included. 

6802 

6783 

ONLY 

£ 

90 

ONLY 

£ 

200 

5605 

BRAKE BLEEDER WRENCH SET 

6 POINT - 6PC 

A 7 piece brake bleeding kit which comprises 6 wrenches with 

integral, captive sockets and a silicone bleed hose fitted with an 

inline one-way valve. The wrenches are colour coded for easy 

identification - this kit is ideal for workshop or home use, as it 

covers a wide range of vehicles. 

• Wrench sizes: 7, 8, 9, 10, 11 & 12mm - all colour coded. 

• Single Hex (6pt). 

• Set comes with 1.2mm silicon hose and check valve. 

• Ideal for bleeding brake and hydraulic clutch systems. 

• Packed in a blow case with EVA foam. All 

wrenches available separately. 

BRAKE CALIPER TOOL SET 

37PC 

Comprehensive brake caliper tool set for wind back and push 

back systems. 

• Applications: Renault, Citroën, Audi, BMW, Ford, Lancia, 

Proton, Rover, Volkswagen, Mini Cooper, Nissan, Saab, Honda, 

Alfa Romeo, Vauxhall/Opel, Subaru, Mazda, Mitsubishi, Volvo, 

Fiat, Mercedes-Benz. 

• Left and right hand threaded wind back tools. 

• Includes 30 adaptors & 5 

reaction plates. 

IMPORTANT: ensure the threaded bar is well 

lubricated with molybdenum disulphide 

grease before use. 

AIR HAMMER 

Professional quality air hammer with variable speed trigger, 

power regulator, and quick-change chuck. 

• Built in power regulator. 

• 2200 blows per minute (bpm). 

• Stroke length 98mm. 

• Air hose size 3/8" ID. Air inlet size 1/4" BSP. Average air 

consumption 4.0cfm. 

6031 

ONLY 

£ 

90 

WORKSHOP PRESS SUPPORT BLOCK 

50 TONNE 

Designed to provide a stable, yet adjustable support base for 

vehicle hubs, and other complex shapes, to allow bearings to be 

pressed out with ease. 

• Supplied with adjustable, heavy duty, steel threaded columns, 

and an adjustable spacer block to provide additional support, 

side guard plates for added security and safety retaining 

screws prevent risk of movement of the block on the press. 

• Length: 285mm, width: 200mm, depth: 50mm, weight: 7.2kg 

(base block). 

• Contents: base block, spacer block, side guard plates (pair), 

heavy duty threaded columns with support sleeves for added 

strength: 3 x 110mm, 3 x 150mm, 3 x 190mm, c/w 4 x machined 

heavy duty washers. 

• CE compliant. Supplied with Test Certificate of Conformance. 

• Made from aircraft grade structural aluminium. 

REGISTERED 


6422 

IMPACT BALL JOINT SEPARATOR SET 

5PC 

Five piece set of ball joint splitter forks, for use with an air 

hammer rather than by hand. 

• Sizes: 20mm, 24mm, 30mm, 35mm, 42mm. 

• For use with the Laser Air Hammer - Part No. 6031 (or similar). 

• Manufactured from chrome molybdenum. 

• Spare parts available - see Laser Part Nos. 1344 (20mm), 1345 

(24mm), 1346 (30mm), 1347 (35mm), 1348 (42mm). 

6032 

ONLY 

£ 

90 

FRONT ENGINE SUBFRAME BUSH TOOL 

FOR VAG 

For the removal and fitting of bushes and ball joints, without 

having to remove suspension legs, subframes, wishbones, trailing 

arms etc from the vehicle. Designed to be used in situ, although 

many can also be used in a workshop press if circumstances 

require. 

• Audi Applications: A3 (from 2003), Audi TT (2006 - 2010). 

• Seat Applications: Altea (from 2004), Leon (up to 2005), Toledo 

111 (2004 - 2009). 

• Skoda Applications: Octavia (2004 - 2010). 

• Volkswagen Applications: Caddy 111 (2004 - 2010), Eos (up 

to 2006), Golf Plus (2005 - 2009), Golf V (2003 - 2009), Golf VI 

(2008 - 2010), Jetta III (2005 - 2010), Touran (up to 2003), Passat 

(up to 2005), Scirocco (up to 2008), Tiguan 

(up to 2007). 

• No hydraulic press required. 

6250 

ONLY 

£ 

300 

BEARING & BUSH 

REMOVAL/INSERTION KIT 

This universal bush and bearing removal tool is ideal for the 

service garage where various combination of tools are required. 

• For use on bushes, bearings, seals. 

• 20 sizes of adaptors ranging from 34 to 72mm (double sized). 

• 4 threaded bars - 350mm long. 

• Spare threaded bars available: 

M10 (Part No. 2473), M12 (Part 

No. 2474), M14 (Part No. 2475), 

M16 (Part No. 2485). 

5178 

ONLY 

£ 

280 

7018 

ONLY 

£ 

130 

£ 

40 

SUSPENSION COIL SPRING COMPRESSOR 

HEAVY DUTY 

Designed to hook securely onto the spring and allow the user to 

compress the spring in a controlled manner. 

• Hand held suspension spring compressor with twin threaded 

rams. 

• Adjustable jaws to suit coil diameters up to 240mm. 

• Jaw capacity: 23mm - 280mm. 

• Maximum spring load: 1200kg. 

• Equipped with safety clamps. 

BRAKE ADAPTOR SET 

ADJUSTABLE 

A three piece set of essential brake caliper rewind adaptors to fit 

a huge range of vehicles. Two of the adaptors have adjustable pins 

and the third adaptor allows the adjustable adaptors to be used 

with a 3/8" drive wind back tool (such as Laser Part No. 1314). 

Also compatible with two-pin windback tools (such as Laser Part 

No. 3935). 

• Applications include: Audi, BMW, Iveco Daily, Renault, Range 

Rover Evoque, Seat, Volkswagen & Volvo. 

• Includes magnetic 2 pin drive to 3/8"D adaptor. 

• Adjustable two pin adaptor fits 100s of cars. 

• Adjustable three pin adaptor only to be used with electronic 

park brake (EPB) tools. 

• Can be used with Laser's Brake Caliper Rewind Tools, Part Nos: 

3993, 3991, 5626, 3835, 5605, 3940, 4511, 5094. 

6090 

ONLY 

£ 

35 

BRAKE CALIPER SOCKET & BIT SET 

FOR GERMAN VEHICLES - 11PC 

An 11 piece set of sockets, specifically designed for use on a range 

of German vehicles. 

• Applications: Volkswagen, Audi, BMW, Ford, Mercesdes-Benz, 

Porsche. 

• 7 impact Hex bits: 1/4"D: 9mm x 20mm long; 3/8"D: 7mm & 

8mm x 24mm long, 9mm x 50mm long, 7mm x 65mm long, 

7mm x 92mm long, 11mm x 100mm long. 

• 2 x 1/2"D specialist sockets: 11.5 x 50mm long x 10 point (for 

Porsche); AS22 x 48mm long x 7 point (Audi S5). 

• 2 x 1/2"D sockets: 15mm & 20mm x 50mm long x 10 point. 

RATCHET BRAKE PISTON SPREADER 

Works on single, twin and quad pistons. 

• The ratchet evenly spreads the force on the pistons. 

• Fast and easy to use. 

• Cushioned grip handle. 

Not for sale in 

the USA. 

6743 

ONLY 

£ 

35 

TWIN FUNCTION BRAKE PIN PUNCH SET 

3PC 

A set of specially designed pin punches, particularly suited to use 

on vehicle brake pad pins where the pins are a tight fit and the 

ends are at risk of spreading out (mushrooming) and jamming 

in the caliper, which can happen when standard flat punches are 

used. This issue is often seen with Brembo type calipers. Each 

punch is made up of 2 punches in one, the short punch has a 

specially machined, concaved end that ensures the initial force 

of impact is concentrated on the circumference of the pin to 

significantly reduce the chances of mushrooming. Once the pin 

has moved the longer pin can be used to continue the removal 

process. The perfect solution to avoid chipping your powder 

coated brake calipers. 

• Punch sizes: 3mm, 4.8mm, 5.5mm. 

• Manufactured from chrome vanadium & plated for corrosion 

resistance. 

• Punches are considered consumable; spares available – 

please see Laser Part Nos. 7866 (3mm), 7867 (4.8mm), 7868 

(5.5mm). 

REGISTERED 


BREMBO BRAKE PIN 

ONLY 

£ 

100 

BRAKE CALIPER GUIDE 

THREAD REPAIR KIT 

Complete with a Titanium coated core drill, tap and 10 threaded 

inserts 

• Suitable for Volkswagen Audi Group (90mm to centre to 

centre), Vauxhall/Opel (94mm centre to centre, Ford (105mm 

centre to centre). 

• Repairs brake caliper guide threads. Permanent repair. 

• Space guides provided to ensure caliper guides are spaced 

correctly. 

• 9mm tap (Part No. 0253), tap and 10 threaded inserts (Part No. 

5038), Titanium coated core drill (Part 

No. 0182). 

• Supplied in a blow mould case. 

5037 

ONLY 

£ 

60 

BRAKE PAD THICKNESS GAUGE 

• Check the life of the brake pads without removing any 

components. 

• Easy to read colour coded scale. 

• Gives a quick reference to brake pad condition. 

• Manufactured from lightweight Aluminium. 

ONLY 

£ 

400 

COIL SPRING COMPRESSOR 

MACPHERSON STRUTS 

Specifically designed for MacPherson struts fitted to most makes 

of vehicle and comes complete with a robust shaft which extends 

up to 300mm and 3 sizes of pressure plates. 

• The anti-slip locking mechanism ensures the struts are 

compressed safely. 

• 3 size of pressure plates: 80 - 115mm, 110- 150mm & 140 - 

195mm. 

• An adaptor for conical springs fitted 

to some Alfa Romeo, Chrysler, 

Nissan, Seat & Volkswagen is 

included. 

4871 

ONLY 

£ 

300 

RACK END REMOVER/INSTALLER 

35-45MM 

This tool is designed to remove the axle joint / track rod from the 

steering rack measuring from 35mm to 45mm diameter. 

• Enables the removal with the track rod insitu. 

• 35 - 45mm diameter. 

• Can be used with 1/2"D wrench or 27mm spanner. 

SHOCK ABSORBER & MACPHERSON 

STRUT TOOL KIT 

24PC 

Most suspension strut top fixings require the top of the strut to 

be held while the fixing nut is removed. The design of the tools 

required for this operation vary considerably from manufacturer 

to manufacturer and often even across ranges. The 7673 has been 

specifically designed for repairing and replacing shock absobers 

including MacPherson strut type assemblies. 

• Contents: 1 x 1/2"D (21mm Hex) Go Thru' ratchet; 2 x magnetic 

extension bars 1/2"D - 95mm and 190mm; 1 x special extension 

bar 120mm. 

• 3 x slot socket adaptors: 5mm x 8mm, 6mm x 8mm, 8mm x 

11mm. 

• 7 x Go Thru' sockets 16mm, 17mm, 18mm, 19mm, 21mm, 

22mm, 24mm x 78mm long. 

• 6 x 8mm Hex shank bits: Hex 5mm, 6mm, 7mm, 8mm, Spline 

M10 and Star* T50 and 4 Hex socket adaptors: 7mm, 8mm, 

9mm, 10mm. 

• The Go Thru' socket design combined with the special 

extension socket allows for access to a depth of 188mm. 

7673 

ONLY 

£ 

120 

RACK END REMOVER/INSTALLER 

28MM - 35MM 

Track rod (steering arm) remover and installer to enable the 

removal with the track rod insitu. 

• Size range: 28 - 35mm. 

• Length: 400mm. 

• Can be used with a 1/2"D wrench or a 27mm spanner. 

HANDS FREE SUSPENSION ARM LEVER 

Specifically designed to pull and hold down the lower suspension 

arms to allow separation of the hub from the lower arms. 

• Also assists in the separation of lower ball joint or suspension 

struts from the hub. 

• Makes the job easier and safer with hands free operation. 

• Suitable for most cars and light commercial vehicles. 

• Made in Italy - Patent No 1479482. 

6936 

ONLY 

£ 

200 

STRUT NUT SOCKET SET 

5PC 

A set of five Bi-Hex (12pt) sockets with cut away profile for 

removing and replacing strut nuts. Covers most popular sizes for 

European vehicles. 

• 1/2"D cut away sockets allows 90° Hex key to hold the strut 

whilst tightened to correct torque with a torque wrench (Hex 

key not supplied). 

• Sizes: 18mm (OD 25.9mm), 19mm (OD 27mm), 21mm (OD 

27.9mm), 22mm (OD 29.9mm), 24mm (OD 31.9mm). 

• Supplied on a socket rail for easy storage. 

• Manufactured from Chrome Vanadium. 

7064 

7865 

6678 

4765 

5122 6496 

ONLY 

£ 

50 

ONLY 

£ 

20 

ONLY 

£ 

20 

ONLY 

£ 

50 

ONLY 

£ 

50 

ONLY 

£ 

50 

Dingbro Ltd 


59



ABAC Piston Compressors 


ABAC 

SINGLE STAGE BELT DRIVEN COMPRESSORS 

Advanced user-friendliness, Maximum comfort, 

Increased performance. 


• Ultimate durability and efficiency 

• Single stage belt driven compressors 

• Reliable power and performance in combination with user 

friendly features. 

• Belt guard improves airflow over pump 

• Reduced wear thanks to great cooling 

FROM 

£ 

499 

BELT DRIVEN SINGLE STAGE LUBRICATED - PRO SERIES COMPRESSORS - 3-6 HP 

MADE IN 

ITALY 

ABAC 

FULL FEATURE TWO STAGE BELT 

DRIVEN COMPRESSOR 

Two stage compressors with tank and dryer. 


• An all-in-one range professional piston compressors. 

• User-friendly pre-connected dryer 

• No separate installation 

• Space saving solution 

• Durable and strong components 

• Proven and well established technology 

• Clear oil-level indicators 

• Cast iron pump cylinder for longer life 

• Finned after cooler to lower the compressed air 

temperature 

Part No. 

Model 

Capacity Pressure Motor Receiver Noise 

CFM L/min Bar Psi HP kW Litres dB(A) 

Volt 

Offer 

Price 

Weekly 

Price 

5yr Lease 

MADE IN 

ITALY 

4116025017 ABAC PRO A39B 90 CM3 13.8 393 10 145 3 2.2 90 73 230/1/50* £ 

499 £2.65† 

4116025015 ABAC PRO A39B 150 FM3 13.8 393 10 145 3 2.2 150 73 230/1/50* £ 

549 £2.91† 

4116024539 ABAC PRO A39B 150 FT3 13.8 393 10 145 3 2.2 150 73 400/3/50 £ 

629 £3.34† 

4116025016 ABAC PRO A39B 200 FM3 13.8 393 10 145 3 2.2 200 73 230/1/50* £ 

629 £3.34† 

4116024541 ABAC PRO A39B 200 FT3 13.8 393 10 145 3 2.2 200 73 400/3/50 £ 

985 £5.20† 

Part No. 

Model 

BELT DRIVEN TWO-STAGE LUBRICATED COMPRESSOR - 4 HP 



Volt 

Offer 

Price 

Weekly 

Price 

5yr Lease 

4116024868 ABAC PRO A39B 270 FM3 TANDEM 27.6 786 10 145 3 + 3 2.2 + 2.2 270 73 230/1/50** £ 

2,799 £14.86† 

4116000159 B 5900B/270 FT 5.5 FFO 22.9 653 11 160 5.5 4 270 78 400/3/50 £ 

2,635 £13.99† 

*Single phase - run off a 16 amp supply 

**Tandem single phase unit requires a 32amp single phase supply 

ABAC 

TWO-STAGE BELT DRIVEN COMPRESSORS 

ABAC 

SILENCED COMPRESSOR RANGE 

Two stage, lubricated, with power ratings from 4 to 20 HP, 

200 to 900 litres tank, working pressure from 1 to 11 BAR. 


• Two stage compression providing bigger flows and higher 

pressure, resulting in better efficiency. 

• Proven and well established technology 

• Durable strong components 

• Easy maintenance 

• Quick access to air filter 

• Oil sight glass allowing a quick check on the oil level 

Silenced, flexible and user friendly in operation 

Strong and durable designs 


• Noise reducing cover 

• Easy open and closing for maintenance 

• Hood with foam to reduce noise 

• Well designed cooling flows 

MADE IN 

ITALY 

MADE IN 

ITALY 

Part No. 

BELT DRIVEN TWO-STAGE LUBRICATED - PRO SERIES COMPRESSORS - 4 - 10 HP 

Model 



Volt 

Offer Price 

4116019614 ABAC PRO B4900 200 FT4 18 514 11 160 4 3 200 78 400/3/50 £ 

1,265 £6.71† 

4116019759 ABAC PRO B5900B 200 FT5.5 22.9 653 11 160 5.5 4 200 78 400/3/50 £ 

1,485 £7.88† 

Weekly 

Price 

5yr Lease 

4116020193 ABAC PRO B6000 270 FT7.5 28.9 827 11 160 7.5 5.5 270 78 400/3/50 £ 

2,035 £10.80† 

4116020794 ABAC PRO B7000 270 FT10 YD 42.4 1210 11 160 10 7.5 270 78 400/3/50 £ 

2,845 £15.10† 

Part No. 

Model 

SILENCED BELT DRIVEN LUBRICATED COMPRESSORS - 4 - 7.5 HP 



Volt 

Offer Price 

4116007364 S A39B 200 FM3 13.8 393 10 145 3 2.2 200 71 230/1/50* £ 

1,420 £7.54† 

Weekly 

Price 

5yr Lease 

4116007333 S B5900B 270 FT5.5 18.4 525 11 160 5.5 4 270 71 400/3/50 £ 

2,510 £13.32† 

4116007062 B5900 LN 270 5.5 20.1 570 11 160 5.5 4 270 67 400/3/50 £ 

4,099 £21.76† 

*Single phase - run off a 16 amp supply 

Dingbro Ltd 


61





ABAC 

SPINN SCREW COMPRESSORS 2.2 - 15KW 

ABAC GENESIS SCREW 

COMPRESSORS 5.5KW - 22KW 


• Genesis is a full feature machine tank mounted with integral refrigerant 

air dryer and G grade coalescing line filter 

• Low noise levels - axial fan on 7.5-15kw units and radial fan on 

18.5-30kw units 

• Max ambient 46 deg C 

• Intake filter mats for compressor and electrical cabinets fitted as 

standard 

• Phase sequence relay fitted as standard 

• ABB / Siemens contactors and Mk V standard controller for optimum 

operation 


• Genesis is a full feature machine tank mounted with integral 

refrigerant air dryer and G grade coalescing line filter 

• Low noise levels - axial fan on 7.5-15kw units and radial fan 

on 18.5-30kw units 

• Max ambient 46 deg C 

• Intake filter mats for compressor and electrical cabinets 

fitted as standard 

• Phase sequence relay fitted as standard 

• ABB / Siemens contactors and Mk V standard controller for 

optimum operation 

TWO YEAR 

WARRANTY 

TWO YEAR 

WARRANTY 

MADE IN 

ITALY 

MADE IN 

ITALY 

SPINN SCREW COMPRESSORS 4 - 7.5kW 

Part No. 

Model 


CFM m3/min Bar Psi HP kW Litres dB(A) 

Volt 

Offer 

Price 

5yr Lease 

GENESIS SCREW COMPRESSORS 11kW - 18.5kW - C55*- C67 Infologic Standard Mk V Controller 

4152008009 Spinn 410 200 V400 16.6 0.47 10 145 5.5 4 200 62 400/3/50 £ 

4,690 £24.89† 

4152008021 Spinn 5.510 270 V400 21.2 0.6 10 145 7.5 5.5 270 64 400/3/50 £ 

5,089 £27.01 

Part No. 

Model 


CFM m3/min Bar Psi HP kW Litres dB(A) 

Volt 

Offer 

Price 

5yr Lease 

4152008014 Spinn.E 410 200 V400 16.6 0.47 10 145 5.5 4 200 62 400/3/50 £ 

5,925 £31.45† 

4152008026 Spinn.E 5.510 270 V400 21.2 0.6 10 145 7.5 5.5 270 64 400/3/50 £ 

6,350 £33.70† 

4152022624 SPINN 7.5X 10 TM270* 35.2 1.0 10 145 10 7.5 270 65 400/3/50 £ 

6,710 £35.61† 

4152022643 SPINN 7.5XE 10 TM270* 35.2 1.0 10 145 10 7.5 270 65 400/3/50 £ 

7,890 £41.88† 

4152025406 GENESIS 11 10 400/50 270 CE 52.7 1.49 10 145 15 11 270 65 400/3/50 £ 

5,995 £31.82† 

4152025545 GENESIS 15 10 400/50 270 CE 73.6 2.08 10 145 20 15 270 67 400/3/50 £ 

8,495 £45.09† 

4152025548 GENESIS 15 10 400/50 500 CE 73.6 2.08 10 145 20 15 500 67 400/3/50 £ 

8,499 £45.11† 

4152025551 GENESIS 18 10 400/50 500 CE 95 2.69 10 145 25 18.5 500 69 400/3/50 £ 

9,995 £53.05† 

* E denotes dryer 

Dingbro Ltd 


63



Powatec 

Powatec 

By 

WORLDWIDE PARTNER OF 

THE AUTOMOTIVE INDUSTRY 

POWATEC ATF EVOLUTION MACHINE 

ENGINE CLEANING & PROTECTION 

OFFER PRICE 

£7.20 

PETROL FUEL SYSTEM 

OFFER PRICE 

£7.30 

OFFER PRICE 

£7.20 

The Powatec ATF Machine is a fully 

featured automatic transmission 

cleaner and fluid exchanger from 

Powatec. All of our ATF machines 

come with commissioning and 

aftersales support from our 

technical experts. 

The Powatec ATF EVOLUTION is supplied with 

a comprehensive range of adaptors, allowing 

connection to most transmission units, including 

double clutch and CVT types. The ATF machine 

also uses load cell weighing technology and 

software to provide a consistent, reliable and 

accurate 99.9% fluid exchange. It features a built 

in printer and large display screen with easy to 

read gauges to make it user friendly for all types 

of technicians. 

ENGINE FLUSH 

Suitable for all types of engine oil. For use in all petrol 

and diesel engines. Removes contamination and resin 

deposits in the entire oil and lubricating circuit, residue and 

carbonisation in the piston rings and the upper cylinder area 

and neutralises harmful engine acids. 

Directions 

Add to old oil prior to the oil change. Allow the engine to idle 

for 10-15 minutes. Drain as normal, fit new filter and fill with 

new oil. Treats up to 6 litres of oil. Mixing ratio: 1:15. 

PWT1001 

981AA2560 

375ml 

VALVE & INJECTOR CLEANER 

Use in the fuel system of petrol engines 

equipped with carburettor, fuel injection, direct 

injection (FSI, GDI,…) catalytic converter or 

turbocharger. Effectively removes carbon 

deposits from the fuel injection system, valves, 

intake and combustion. 

Directions 

Add regularly every 3-4 months into the fuel 

tank. Observe mixing ratio (1:200). 375ml treats 

up to 80 litres of petrol. 

PWT2233 

981AA2640 

375ml 

COMPLETE PETROL SYSTEM CLEANER 

For all petrol powered engines e.g. FSI, incl. Turbo engines. 

Recommended for catalytic converters, turbo and direct 

injection. The entire fuel system will be cleaned for perfect 

fuel nebulization at the nozzles and valves. Binds condensed 

water and ensures a clean and powerful combustion, good 

performance and low fuel consumption. 

Directions 

Use during every service at intervals recommended by the 

manufacturer. Add to the fuel tank. 375ml treats up to 80 litres 

of petrol, approx. 1% of the tank volume for larger tanks. 

PWT1101 

981AA2570 

375ml 


• Exchanges 99.9% of the transmission fluid 

• Detergent based cleaning cycle 

• Automatic flow direction recognition 

• Incremental fluid level adjustment 

• Customer job print out via built in thermal 

roll printer 

• Simple operation with minimal mess 

• Easily comply with VM transmission service 

requirements 

• Robust and portable 

• Easy emptying of old and new oil tanks 

• New adaptors under continual development 

SCAN ME 

TO WATCH 

THE DEMO 

DIESEL FUEL SYSTEM 

PART NO: 987AB221K 

OFFER PRICE 

£ 

2,795 

OFFER PRICE 

£7.10 

OFFER PRICE 

£8.60 

OFFER PRICE 

£10.90 


COMPLETE DIESEL SYSTEM CLEANER 

Specifically developed for all high pressure direct injection diesel 

engines with common rail or pump injector. This high tech product 

has been developed from extensive research and designed 

to meet the exact requirements of the modern diesel system. 

Exceeds the requirements of DIN EN ISO 12156-1 (HFRR test). 

Directions 

Pour directly into the tank or apply via special cleaning equipment. 

375ml treats up to 80 litres of diesel. Mixing ratio: 1:200. 

DPF SUPER CLEAN 

The most economical way to clean and protect the 

particulate filter. This high powered special diesel 

additive solution is used as a regeneration aid for 

the diesel particulate filter system and can be used 

in all diesel engines and mixed with all diesel fuels. 

Directions 

Add to the tank before filling up with diesel fuel. 

375ml is sufficient for 40 to 80 litres of diesel fuel. 

We recommend regular use once every 3 months. 

DPF / CATALYST CLEANER 

Dissolves and removes all contamination and soot residues 

from the particulate filter and the catalyst – no disassembling 

required Restores the complete function of the diesel 

particulate filter and catalyst. This product is also ideal for 

EGR-valve cleaning. 

A COMPREHENSIVE 

RANGE OF ADAPTORS 

POWERED BY 

PWT2101 

981AA2580 

375ml 

PWT6171 

981AA2590 

375ml 

PWT2985 

981AA2600 

400ml 

Dingbro Ltd 


65



Unilite 

Exclusive to The Parts Alliance in the automotive sector! 

Milwaukee 

RECHARGEABLE 

INSPECTION LIGHT 

NEW 

HIGH CRI 96+ 

INSPECTION LIGHT 

NEW 

M18FPP3B-525B M18 & M12 

AUTOMOTIVE WORKSHOP PACK 

• 625 Lumen white COB LED, 6500k 

• 250 Lumen white SMD LED spot beam 

torch, 6500k 

• UV LED on front 

• Super tough aluminium & polycarbonate 

• Rear pocket clip attachment 

• Strong integral magnets on base and 

pocket clip 

• Glow-in-the-dark strip around LED 

• Battery level & charging indicators LEDs 

• Faster USB type-C charging - 3 hrs 

• 1m USB charging cable included 

BATTERY: 3.7v 2500mAh Li-ion Rechargeable 

WEIGHT: 190g 

DIMENSION: 188 x 35 x 35mm 

USB RECHARGEABLE I 

NSPECTION PEN LIGHT 

625 

Lumen 

ONLY 

£ 

42 


• 1250 Lumen 10W COB LED 

• High CRI 96+ 3 coloured COB LED 

• CCT: 2700k / 4500k / 6500k 

• Smooth dimming function 

• 250 Lumen 3W SMD LED top torch 

• 5W UV LEDs on front 

• SUper tough construction 

• Strong integral magnets on back & base 

• Retractable 360° rotating hanging hook 

• Glow-in-the-dark strip around LED 

• Battery level & charging indicator LEDs 

• Built-in power bank for charging devices 

• Faster USB type-C charging - 5 hrs 

• Magnetic charging dock & 1m USB charging 

cable included 

BATTERY: 3.7v 5000mAh Li-ion Rechargeable 

WEIGHT: 406g 


1250 

Lumen 

THE 

BRIGHTEST 

INSPECTION 

LAMP 

AVAILABLE 

ONLY 

£ 

52 


BUY A HIGH CRI 96+ INSPECTION LIGHT 

GET A MICRO LED HEADLIGHT FREE! 

INCLUDES 

• M18 High Torque Wrench 

• M12 Tyre Inflator 

• M12 Torch 

• 3 x M18 Batteries 5.0Ah 

• 2 x M12 Batteries 2.0Ah 

• • M12/18 Charger 

NORMALLY 

£ 

695 

NOW ONLY 

£ 

499 

INCLUDES 

MILWAUKEE WHEEL BAG 

PART NO: GSF987AB2910 / GEQ4933478257 

• 125 Lumen White CREE ® SMD LEDs 

• Pocket clip for easy transportation 

• Strong magnet within the body for easy 

attachment 

• Non-slip grips down the sides of the body 

• Easy press tactical micro switch 

• Micro-USB cable included 

• Red-to-Green charge indicator 

• Charging port with protective cover 

BATTERY: 3.7v 350mAh Li-Polymer 

Rechargeable 

WEIGHT: 30g 


RECHARGEABLE 

INDUSTRIAL SITE LIGHT 

• 3000 Lumen 30W SMD LEDs 

• Powerful Li-ion battery with battery 

level indicator 

• Battery pack can easily be removed and 

used as a USB power bank 

• 50% dimming function to increase battery 

runtime 

• Adjustable head for light angle 

• Tough polycarbonate housing 

• Acrylic LED diffuser for even light 

dispersion 

• Super strong rotating magnetic base 

BATTERY: 7.4v 6600mAh Li-ion 

Rechargeable Battery Pack 

WEIGHT: 1880g 


• 750 Lumen 10w White COB LED 

• Industrial strength polycarbonate 

and rubber housing 

• Mains cable operated 

• 230v ultra tough 5m cable 

• Hanging hook for easy placement 

• IK07 shockproof 

125 

Lumen 

3000 

Lumen 

MAINS POWERED INSPECTION 

LED LEAD LAMP 

ONLY 

£ 

18 

Part No: 987AB0020 

HURRY! 

WHILE 

STOCKS 

LAST 

ONLY 

£ 

90 


• Rubberised handle for extra grip 

• Smooth even beam spread 

• Impact resistant to 1m 

• Chemical and corrosion resistant 

BATTERY: 230V Mains Powered 

WEIGHT: 2kg including 5 metre cable 


• 75 Lumen White LED 

• 2 x red LEDs - On and quick flashing 

• Smooth reflector 

• 45º rotational head 

• Retractable shield to angle light downwards 

WORTH 

£ 

15 


BATTERY: 1 ×1.5v AA Panasonic Alkaline Battery (included) 

WEIGHT: 73g (with battery) 

DIMENSION: Headlight: 64 x 43 x 35mm 

USB RECHARGEABLE 

MICRO HEADLIGHT 

• 125 Lumen White CREE ® LED 

• 2 x 3mm red LEDs for night vision 

• Micro-USB cable included 

• Red-to-Green charging indicator 

• Easy push micro switch 

• 45° rotational head 

• Strong ABS housing 

• 1m impact resistant 

• IPX5 water resistant 

• Fully adjustable non-slip silicone headband 

BATTERY: 3.7v 520mAh Li-Polymer 

Rechargeable 

WEIGHT: 28g (with battery) 

DIMENSION: Headlight: 47 x 27 x 37mm 

HURRY! 

WHILE 

STOCKS 

LAST 

750 

Lumen 

• Strong ABS housing 

• Fully adjustable headband 

• Easy open to change battery 

• IP44 dust & water resistance 

125 

Lumen 

HURRY! 

WHILE 

STOCKS 

LAST 

75 

Lumen 

SPECIAL 

OFFER 

ONLY 

£ 

22 


ONLY 

£ 

20 


M18FPP3E2-524P 

M18 & M12 AUTOMOTIVE 

POWER PACK 

NORMALLY 

£ 

695 

NOW ONLY 

£ 

499 

NORMALLY 

£ 

595 

NOW ONLY 

£ 

499 

FEATURES 

• M18 FMTIWF12 - M18 FUEL ½″ mid torque impact 

wrench with friction ring 

• M12 FIR12 - M12 FUEL sub compact ½″ ratchet 

• M12 FIW38 - M12 FUEL sub compact ⅜″ impact wrench 

• 2X M18 B5 - M18 5.0 Ah battery 

• 2X M12 - 2.0Ah Batteries 

• M18/12 Charger 


M18FPP2J2-502P 

M18 HIGH TORQUE ½″ IMPACT 

WRENCH & GRINDER PACK 


INCLUDES 

PACKOUT CASE 

M18ONEIWF12-502X 

ONE-KEY FUEL COMPACT ½″ 

IMPACT WRENCH WITH FRICTION RING 

FEATURES 

• M18 FIWF12 but with ONE-KEY technology 

• Connect via Bluetooth ® with the 

ONE-KEY app 

• Complete tool customisation via 

ONE-KEY app to tune the tool 

to your needs 

• Control speed, torque, start - 

end speeds and LED light 

• Configure to any application 

choosing optimum tool settings 

for repeatable precision 

• Program / save profiles for unmatched 

control 

NORMALLY 

£ 

647 

NOW ONLY 

£ 

399 

• Select from a range of application profiles or quickly create your own 

for perfect results on every trigger pull 

• Save up to 4 custom settings to the tools memory for fast selection on 

the jobsite 

• ONE-KEY app also provides inventory function for total management 

of your complete tool / equipment fleet 

PART NO: GSF987AA3890 / GEQ4933451375 

Dingbro Ltd 


67



Milwaukee 

Milwaukee 

M18FHZ-0X 

M18 FUEL HACKZALL 

M18CAG115XPDB-0 M18 

115 MM ANGLE GRINDER 

WITH PADDLE SWITCH 

HD18AG-115-0 M18 

115 MM ANGLE GRINDER 

WITH PADDLE SWITCH 

M18BLPP2A2-502X 

M18 BRUSHLESS 

TWIN POWERPACK 

M12FPD-602X 

M12 FUEL SUB COMPACT 

PERCUSSION DRILL 

M12BRPT-0 M12 

SUB COMPACT RIVET TOOL 

TWIN POWERPACK 

FEATURES 

• POWERSTATE brushless motor provides increased 

efficiency, lasts longer and delivers maximum power 

• REDLINK PLUS intelligence system delivers an advanced 

digital overload protection for tool and battery and uniquely 

enhances the tool performance under load 

• REDLITHIUM battery pack provides superior pack 

construction, electronics and fade-free performance to 

deliver more run time and more work over pack life 

• 22mm stroke length for controlled cutting with a no load 

stroke rate of 3000 spm 

• Pivoting shoe allows the user to optimise his cutting position 

• Built in LED light improves visibility in low light cutting 

applications 

• Patented FIXTEC clamp for quick and efficient blade change 

• Flexible battery system: works with all MILWAUKEE ® M18 

batteries 

FEATURES 

• High performance 4-pole motor delivers maximum power 

whilst (optimising) maximising the power to weight ratio 

• REDLINK overload protection electronics in tool and battery 

pack deliver best in class system durability 

• Reduced height of gear box and slim girth design deliver 

optimum ergonomics 

• Non-lockable switch for best user protection and preventing 

automatic start up 

• Burst resistant and tool-free safety guard for best user 

protection and fast adjustment 

• Individual battery cell monitoring optimises tool run time and 

ensures long term pack durability 

• Works with all MILWAUKEE ® M18 batteries 

FEATURES 

• High performance 4-pole motor delivers maximum power 

whilst (optimising) maximising the power to weight ratio 

• REDLINK overload protection electronics in tool and 

battery pack deliver best in class system durability 

• Reduced height of gear box and slim girth design deliver 

optimum ergonomics 

• Non-lockable switch for best user protection and 

preventing automatic start up 

• Burst resistant and tool-free safety guard forbe st user 

protection and fast adjustment 

• Individual battery cell monitoring optimises tool run time 

and ensures long term pack durability 

• Works with all MILWAUKEE ® M18 batteries 

FEATURES 

• M18 BLPD2 - M18 brushless percussion drill 

• M18 BLID2 - M18 brushless ¼″ Hex impact driver 

• 2 x M18 B5 - M18 5.0 Ah battery 

• 1 x M12-18 FC - Dual Rapid Charger 

INCLUDES 

PACKOUT CASE 

FEATURES 

• Brushless POWERSTATE motor delivers more power in a 

more compact size 

• REDLINK PLUS intelligence system delivers an advanced 

digital overload protection for tool and battery and uniquely 

enhances the tool performance under load 


construction, electronics and fade-free performance to deliver 

more run time and more work over pack life 

• Individual battery cell monitoring optimises tool run time and 

ensures long term pack durability 

• 13mm metal chuck for quick bit changes and bit retention 

NORMALLY 

£ 

215 

NOW ONLY 

£ 

179 

PART NO: 

GSF987AA1460 / GEQ4933459887 

NORMALLY 

£ 

255 

NOW ONLY 

£ 

199 

PART NO: 

GSF987AA1310 / GEQ4933451007 

NORMALLY 

£ 

183 

NOW ONLY 

£ 

139 

PART NO: 

GSF987AB2860 / GEQ4933411210 

NORMALLY 

£ 

465 

NOW ONLY 

£ 

379 

PART NO: 

GSF987AB2950 / GEQ4933464523 

NORMALLY 

£ 

299 

NOW ONLY 

£ 

249 

• Electronic clutch with 16 torque 

settings, plus 1 for locked clutch 

drilling and 1 for locked clutch 

hammer 

• Fuel gauge displays remaining 

charge 

• Bright LED workspace illumination. 

• Works with all MILWAUKEE ® M12 

batteries 

PART NO: 

GSF987AB2960 / GEQ4933459807 

FEATURES 

• Up to 325 x 4.8mm stainless steel rivets on a single charge 

with a 2.0 Ah battery pack 

• Suitable for all aluminium, steel, stainless steel and copper 

rivets up to 4.8mm 

RATCHETS 

M12FIR38LR-0 

M12 FUEL 3/ 8 ″ 

EXTENDED 

REACH RATCHET 

FEATURES 

• With up to 75Nm of max torque and 200 

rpm’s, this tool is the ideal fastening 

solution for automotive mechanics, 

maintenance and repair professionals 

• The industry leading FUEL technology 

combined with a reinforced mechanism 

and investment cast steel yoke housing 

provides greater durability for the 

professional user 

• Extended reach ratchet adding 

additional 82mm of length for access 

into tight spaces 

• Variable speed trigger provides ultimate 

control of the tool 

• Premium rubber overmold withstands 

corrosive materials and provides 

increased comfort when in use 

• Flexible battery system: works with all 

MILWAUKEE ® M12 batteries 

M12 SUB COMPACT 

RATCHET 3/ 8 ″ 

POWERPACK 

FEATURES 

• Pneumatic performance with cordless 

convenience, 47Nm of torque and no load 

speed of 250 rpm 

• REDLINK overload protection 

electronics in tool and battery 

pack deliver best in class system 

durability 

• Reinforced housing - provides high 

durability similar to steel ratchets 

• Compact design - ideal for tight spaces 

and small engine bays 

• Variable speed metal paddle switch trigger 

- provides greater user control during 

application 

• Individual battery cell monitoring 

optimises tool run time and ensures long 

term pack durability 



M12 FUEL SUB 

COMPACT⅜3/ 8 ″ RATCHET 

FEATURES 


rpm’s, 

this tool is the ideal fastening solution for 

automotive mechanics, maintenance and 

repair professionals 

• Low profile head design allows users 

better access in tight spaces 






• REDLINK PLUS intelligence system 

delivers an advanced digital overload 

protection for tool and battery and 

uniquely enhances the tool performance 

under load 

• Supplied with ¼″ adaptor 



M12FIR38-201B 

M12 FUEL 

SUB COMPACT 

3/ 8 ″ RATCHET 

FEATURES 
















under load. 

• Supplied with ¼″ adaptor 


MILWAUKEE ® M12 

batteries 

M12FIR12-0 

M12 FUEL SUB 

COMPACT ½″ 

RATCHET 

FEATURES 
















under load 



• Rivets in one stroke with a 20.32mm stroke length 

• Retention nose pieces hold rivets in any orientation 

• Tool-free access to easily clean jaws. On-board nose piece 

storage and removal tool for user convenience 

• On board fuel gauge and LED light for added user convenience 

and illumination in low lit working conditions 

• Ergonomic design with 273mm H x 66.8mm W x 165mm in 

length without mandrel collector 

• Integrated belt hook and lanyard tie off point 





batteries 

• Supplied with 4 x retaining tips 

NORMALLY 

£ 

215 

NOW ONLY 

£ 

179 

PART NO: 

GSF987AB0160 / GEQ4933464404 

NORMALLY 

£ 

175 

NORMALLY 

£ 

256 

NORMALLY 

£ 

193 

NORMALLY 

£ 

215 

NORMALLY 

£ 

193 

NOW ONLY 

£ 

179 

PART NO: GSF987AB2780 / 

GEQ4933471500 

NOW ONLY 

£ 

195 

PART NO: GSF987AA9830 / 

GEQ4933448110 

NOW ONLY 

£ 

169 

PART NO: 

GSF987AA1260 / GEQ4933459797 

NOW ONLY 

£ 

179 

PART NO: 

GSF987AA1240 / GEQ4933459799 

NOW ONLY 

£ 

169 

PART NO: 

GSF987AA1270 / GEQ4933459800 

Dingbro Ltd 


69



Milwaukee 

Milwaukee 

M12FPP2H-622P 

M12 STUBBY IMPACT WRENCH & 

FUEL RATCHET TWIN PACK ⅜″ 

NORMALLY 

£ 

495 

NOW ONLY 

£ 

385 

FEATURES 

• Impact Wrench and a Ratchet 

• 1 x M12 6.0Ah Battery 


• Charger 


INCLUDES 

PACKOUT CASE 

M18 PROMO 

POWERPACK 

INCLUDES 

PACKOUT CASE 

NORMALLY 

£ 

595 

NOW ONLY 

£ 

499 

FEATURES 

• M18 & M12 FUEL Automotive Powerpack 

• 1x M18FHIWF12 

• 1x M12FIWF38 

• 2 x M18B5 Batteries 

• 1 x M12B6 Battery 

• 1 x M12B2 Battery 

• 1 x M12-18 Fast Charger 


M18 FUELCORDLESS 

POLISHER KIT 

FEATURES 

• M18 Milwaukee cordless polisher from with 8 position, 

variable speed selection ranging from 360 - 2200 RPM. 

• Unmatched run time, constant speed electronics with soft 

start for smooth start up. 

• Maximum polishing accessory diameter of 180 mm. 

NORMALLY 

£ 

595 

NOW ONLY 

£ 

499 

• Removable dust screen to prevent 

debris ingress, prolonging motor life. 

• Rubber overmold gear case for 

increased comfort. 

• 2 x M18 B5 Battery 

• 1 x M12-18 FC Charger 

• 1 x HD Box 

PART NO: 

GSF987AA7820 / GEQ4933451551 

M12FIWF12-0 

M12 FUEL SUB COMPACT ½″ 

IMPACT WRENCH 

FEATURES 

• More power, more compact, more control 

• Up to 339Nm of maximum torque 

• ½″ anvil with friction ring for quick and easy socket 

changes 

• Brushless POWERSTATE motor delivers more power in 

a more compact size 

• REDLINK PLUS intelligence system delivers an 

advanced digital overload protection for tool and battery 

and uniquely enhances the tool performance under load 

• REDLITHIUM battery pack 

provides superior pack 

construction, electronics 

and fade-free 

performance to 

deliver more run time and 

more work over pack life 

• Flexible battery system: 

works with all MILWAUKEE ® 

M12 batteries 

NORMALLY 

£ 

170 

NOW ONLY 

£ 

149 

PART NO: 

GSF987AB2010 / GEQ4933464615 

M18ONEFHIWF12-0X 

ONE-KEY FUEL ½″ IMPACT 

WRENCH WITH FRICTION RING 

FEATURES 

• The M18 FUEL high torque impact wrench with ONE- 

KEY technology delivers 1356Nm of fastening torque in a 

compact size of 213mm, which gives more access in tight 

spaces 

• The 4 -Mode DRIVE CONTROL allows the user to shift 

into four different speed and torque settings to maximise 

application versatility 

• Mode 4 bolt removal, provides a maximum nut-busting 

torque of 1898Nm then shifts to 750 rpm for outstanding 

control when removing fasteners 

• The integrated blow counting sensor enhances the 

consistent repeatability of the 

chosen torque setting 

• ONE-KEY tool 

customisation allows 

the user to optimise 

their tool for specific 

applications 

• ONE-KEY tool tracking & 

security offers a cloud-based 

inventory management platform that 

supports both location tracking 

and theft prevention 

• friction ring reception 

• Flexible battery system: works 

with all MILWAUKEE ® M18 

batteries 

NORMALLY 

£ 

395 

NOW ONLY 

£ 

299 

PART NO: 

GSF987AB2920 / GEQ4933459726 

M122BPP2B-202C 

M12 BRUSHED TWIN POWERPACK 

M18ONEFHIWF12-502X M18 FUEL 

ONE-KEY ½″ HIGH TORQUE IMPACT 

WRENCH WITH FRICTION RING 

M18FHZ-0X 

M12 SET1F-202B 

LIMITED 

PROMOTIONAL 

STOCK!! 

M12BPS-0 


POLISHER / SANDER 

FEATURES 

• Variable 2 speed selection (0-2800 / 0-8300 RPM) for both 

polishing and sanding applications 

• REDLINK overload rotection electronics in tool and 


• Large capacity of 76mm polishing sponge and 50mm 

sanding pad size for fast job completion 

• Long run time allows frequent task completion with one 

battery charge 

• Compact design with only 130mm allows access to hard 

areas 

• Spindle lock allows fast, tool free accessory change 


batteries 

• Supplied with polishing pad, sanding pad, polishing sponge 

white, polishing sponge yellow, lambswool, side handle 

M12BPS-421X 


POLISHER / SANDER POWERPACK 

FEATURES 

• Variable 2 speed selection (0-2800 / 0-8300 RPM) for both 

polishing and sanding applications 

• REDLINK overload protection electronics in tool and 


• Large capacity of 76mm polishing sponge and 50mm 

sanding pad size for fast job completion 

• Long run time allows frequent task completion with one 

battery charge 

• Compact design with only 130mm allows access to hard 

areas 

• Spindle lock allows fast, tool free accessory change 

• Detachable 2 position side handle 

• Flexible battery system: works with all MILWAUKEE ® 

M12 batteries 

FEATURES 

• With up to 75Nm of max torque and 200 rpm’s, this tool 

is the ideal fastening solution for automotive mechanics, 


• The industry leading FUEL technology combined with a 

reinforced mechanism and investment cast steel yoke housing 

provides greater durability for the professional user 

NORMALLY 

£ 

275 

NOW ONLY 

£ 

195 

FEATURES 

• Twin Pack contains the following: 

• 1 x 12V M12 BPD Sub-Compact Percussion Drill 

• 1 x M12 BID - M12 sub compact ¼″ Hex impact driver 

• 1 x 6.0Ah M12 Battery 

• 1 x 2.0Ah M12 Battery 


INCLUDES 

CASE 

FEATURES 

• The M18 FUEL high torque impact wrench with ONE-KEY technology delivers 1356Nm 

of fastening torque in a compact size of 213mm, which 

gives more access in tight spaces 

• The 4 -Mode DRIVE CONTROL allows the user to shift into four different speed and torque 

settings to maximise application versatility 

NORMALLY 

£ 

647 

NOW ONLY 

£ 

399 

• Mode 4 bolt removal, provides a maximum nut-busting torque 

of 1898Nm then shifts to 750 rpm for outstanding control when 

removing fasteners 

• The integrated blow counting sensor enhances the consistent 

repeatability of the chosen torque setting 


batteries 

PART NO: GSF987AA1100 / GEQ4933459728 

• Extended reach ratchet adding additional 82mm of length for 

access into tight spaces 

• Variable speed trigger provides ultimate control of the tool 

• Premium rubber overmold withstands corrosive materials and 

provides increased comfort when in use 

NORMALLY 

£ 

208 

NOW ONLY 

£ 

185 

• The LED light illuminates the work 

area while the on-board fuel gauge 

displays remaining run time 



PART NO: 

GSF987AB2740 / GEQ4933471686 

NORMALLY 

£ 

169 

NOW ONLY 

£ 

119 

PART NO: 

GSF987AA9980 / GEQ4933447791 

NORMALLY 

£ 

210 

NOW ONLY 

£ 

179 

PART NO: 

GSF987AA9970 / GEQ4933447802 

Dingbro Ltd 


71



Milwaukee 

M18FPP2AF-564P 

M12 FUEL - M18 FUEL 

POWERPACK 

M18 IMPACT WRENCH 

AND LIGHT PACKAGE 

INCLUDES 

PACKOUT CASE 

INCLUDES 

PACKOUT CASE 

FEATURES 

• M18 FMTIWF12 - M18 FUEL mid torque impact 


• M12 FIW38 - M12 FUEL sub compact 

impact wrench 

• 2 x M18 5.0Ah Batteries 


• 1 x M12 2.0An Battery 

• 1 x Charger 

NORMALLY 

£ 

595 

NOW ONLY 

£ 

499 

FEATURES 

• M18 FHIWF12 - M18 FUEL high torque impact 


• L4 FFL-201 - USB rechargeable folding flood light 

• 3x M18 B5 - M18 5.0 Ah battery 

• M12-18 FC - Dual Rapid Charger 

• 3 pc Shockwave Automotive socket set 

NORMALLY 

£ 

695 

NOW ONLY 

£ 

499 


PART NO: GSF4933472097 / GEQ4933472097 

M18FMTIWF12-502 

M18 FUEL ½ IMPACT 

WRENCHWITH FRICTION RING 

M12FIWF12-622 

M12 FUEL SUB COMPACT 

½ IMPACT RENCH 

INCLUDES 

PACKOUT CASE 

FEATURES 

• The M18 FUEL mid torque impact wrench 

delivers 610Nm in a compact size of only 170mm 

• 3-Mode DRIVE CONTROL allows the user to 

shift into 3 different speed and torque settings to 

maximise application versatility 

• Brushless POWERSTATE motor for longer motor life and more power 

• REDLINK PLUS intelligence system delivers an advanced digital overload 

protection for tool and battery and uniquely enhances the tool performance 

under load 

• REDLITHIUM battery pack provides superior pack construction, electronics 

& fade-free performance to deliver more run time and more work over 

pack life 

• Individual battery cell monitoring optimises tool run 

time and ensures long term pack durability square 

friction ring 

• On board fuel gauge and LED light 

• Flexible battery system: works with all MILWAUKEE® 

M18 batteries 


NORMALLY 

£ 

524 

NOW ONLY 

£ 

379 

FEATURES 

• More power, more compact, 

more control 

• Up to 339Nm of maximum torque anvil with friction ring for quick and easy 

socket changes 

• Brushless POWERSTATE motor delivers more power in a more compact 

size 

• REDLINK PLUS intelligence system delivers an advanced digital 

overload protection for tool and battery and uniquely 

enhances the toolperformance under load 




• Flexible battery system: works with all MILWAUKEE® 

M12 batteries 


NORMALLY 

£ 

269 

NOW ONLY 

£ 

220 

Terms & Conditions 

• Prices shown are for Trade Customers only. 

• Prices exclude VAT, at current rate. 

• Prices correct at time of going to press, 

November 2020. 

• Offer ends 31st March 2021. 

• 72 Prices subject to change without notice. 

• Promotional items subject to availability. 

• Errors & Omissions Excluded. 

• In all cases please contact local branch 

for full application/fitment details. 

• Images shown are for illustration purposes only, 

and may or may not reflect the actual products. 

• Terms & Conditions available FOC upon request. 

Lease example: Bendix Diagnostics 989AA0650 

offer price £1,695 + vat 5 year lease plan 

- No deposit terms, 

£38.99 + vat per month. Weekly equivalent £9.00 + vat per week. 

Subject to status, rental payable by direct debit. Leasing examples 

quoted are approximate and for illustration purposes only. 

• All lease figures are based Dingbro on Ltd a 60 month term lease agreement. 

†• † All lease figures are subject to VAT & status. 

• All offers UK mainland only. 

• All offers available until 31st March 2021 subject to availability. 

• Specifications subject to change without notice. 

• Lease figures may vary according to status. 

• Non home owners & non established businesses 

may attract a higher rate. 

• All lease transactions are subject to a documentation fee.

Parts Alliance Garage Essentials Winter 2020

Create successful ePaper yourself

Delete template?

Save as template?