Manuel technique (pdf, 1.81 MB) - Niko
Manuel technique (pdf, 1.81 MB) - Niko Manuel technique (pdf, 1.81 MB) - Niko
65-411 1. load terminals 6. ‘mode’ LEDs 2. 230V~ power supply terminals 7. ‘bus info’ LEDs 3. ‘error indication’ LEDs 8. ‘select’ key 4. ‘programming’ key 9. control terminals 5. ‘programming’ LEDs 10. ‘load’ LED Fig. 1 38 ➍ ➋ � ➒ ➌ ➎ ➏ ➐ ➑ ε R,L,C ➊ EN
65-411 If everything has been connected correctly and the power is switched on, all LEDs will light up simultaneously for 1s. A connected load can be operated manually by means of the ‘select’ key. The ‘select’ key functions as a simple push button control. 3. PROGRAMMING Putting the dimmer into programming status: Press the ‘programming’ key for >2s. The programming status always starts in section ‘physical select’. The accompanying LED blinks. The order the different sections are run through by repeatedly pressing the ‘programming’ key’ is ‘physical select’, ‘mode’. Saving settings and exiting programming status: press the ‘programming’ key for >2s. If no action is performed in the programming status for 3min., the programming status will be automatically exited without the modifications being saved. A. ‘physical select’ ‘Physical select’ makes sure the dimmer is recognized and activated on the DALI bus in combination with other DALI systems. In combination with the Niko DALI system, this mode has no function as the selection is made automatically. To carry out ‘physical select’, you proceed as follows: Press the ‘programming’ key for > 2s. The dimmer now is in programming status, in section ‘physical select’. The ‘physical select’ LED blinks (see following diagram). To exit the programming status: push the programming key >2s. To switch to ‘mode’, see § B. prog > 2s. EN ε R,L,C 39
- Page 1: 65-411
- Page 4 and 5: 65-411 1. aansluitklemmen belasting
- Page 6 and 7: 65-411 B. Keuze dimprincipe ‘mode
- Page 8 and 9: 65-411 Geheugenfunctie: De dimmer k
- Page 10 and 11: 65-411 - De dimmer is voorzien van
- Page 12 and 13: 65-411 7. TECHNISCHE GEGEVENS - Voe
- Page 14 and 15: 65-411 8. WETTELIJKE WAARSCHUWINGEN
- Page 16 and 17: 65-411 1. bornes de raccordement ch
- Page 18 and 19: 65-411 B. Choix du principe de vari
- Page 20 and 21: 65-411 Fonction mémoire: Le variat
- Page 22 and 23: 65-411 - Le variateur est équipé
- Page 24 and 25: 65-411 7. CARACTERISTIQUES TECHNIQU
- Page 26 and 27: 65-411 8. PRESCRIPTIONS LEGALES - L
- Page 28 and 29: 65-411 1. Lastanschlussklemmen 6.
- Page 30 and 31: 65-411 B. Auswahl des Dimmprinzips
- Page 32 and 33: 65-411 Lichtwertspeicherfunktion: D
- Page 34 and 35: 65-411 - Der Dimmer enthält eine
- Page 36 and 37: 65-411 - Der Dimmer enthält einen
- Page 38 and 39: 65-411 8. GESETZLICHE BESTIMMUNGEN
- Page 42 and 43: 65-411 B. Selection of dim principl
- Page 44 and 45: 65-411 Memory function: The dimmer
- Page 46 and 47: 65-411 - The dimmer is provided wit
- Page 48 and 49: 65-411 7. TECHNICAL DATA - Supply v
- Page 50 and 51: 65-411 8. LEGAL WARNINGS - The inst
- Page 52 and 53: 65-411 1 svorky záťaží 6 LED di
- Page 54 and 55: 65-411 Po poruche napájania si stm
- Page 56 and 57: 65-411 B. Význam LED diód počas
- Page 58 and 59: 65-411 5 LED ‘T’ svieti nepretr
- Page 60 and 61: 65-411 - Záťažová tabuľka: vý
- Page 62 and 63: 65-411 - Záväzné predpisy národ
- Page 64 and 65: 65-411 62 VDC+ DALI+ COMMON- BRIDGE
- Page 66: 65-411 64 ε R,L,C
65-411<br />
If everything has been connected correctly and the power is switched on, all LEDs will light up<br />
simultaneously for 1s.<br />
A connected load can be operated manually by means of the ‘select’ key. The ‘select’ key functions<br />
as a simple push button control.<br />
3. PROGRAMMING<br />
Putting the dimmer into programming status: Press the ‘programming’ key for >2s. The programming<br />
status always starts in section ‘physical select’. The accompanying LED blinks. The order the<br />
different sections are run through by repeatedly pressing the ‘programming’ key’ is ‘physical<br />
select’, ‘mode’.<br />
Saving settings and exiting programming status: press the ‘programming’ key for >2s.<br />
If no action is performed in the programming status for 3min., the programming status will be<br />
automatically exited without the modifications being saved.<br />
A. ‘physical select’<br />
‘Physical select’ makes sure the dimmer is recognized and activated on the DALI bus in combination<br />
with other DALI systems. In combination with the <strong>Niko</strong> DALI system, this mode has no function<br />
as the selection is made automatically.<br />
To carry out ‘physical select’, you proceed as follows:<br />
Press the ‘programming’ key for > 2s. The dimmer now is in programming status, in section<br />
‘physical select’. The ‘physical select’ LED blinks (see following diagram).<br />
To exit the programming status: push the programming key >2s. To switch to ‘mode’, see § B.<br />
prog > 2s.<br />
EN<br />
ε<br />
R,L,C<br />
39