Cleco-2019-full-catalog-v3-links
Specialty ToolsSaw Blades - 3/4” arbor holeUsed on Cleco Dotco Saw’s• Used for sawing non-metallic materialsSpecialty ToolsMODELDESCRIPTIONMAXIMUM DEPTH OF CUT DIAMETER RECOMMENDED USEIN IN (GUIDELINES ONLY)14-2690 DIAMOND CHIP 60/80 GRIT 1” X 5/64” 4 FIBERGLASS, COMPOSITE, CARBON FIBER14-2694* CARBIDE CHIP 36 GRIT 1” X 11/64” 4 HARD RUBBER14-2697* CARBIDE CHIP 80 GRIT 1” X 1/8” 4 FIBERGLASS14-2699* CARBIDE TIP 20 TEETH 1” X 7/64” 4 THIN FIBERGLASS, PLASTIC LAMINATES TO 1/8” THICK14-2700* CARBIDE TIP 20 TEETH 1” X 7/64” 4 THICKER FIBERGLASS, PLASTIC LAMINATES TO 1/2” THICK14-2701* CARBIDE CHIP 36/80 GRIT 1” X 1/8” 4 FIBERGLASS, HARD RUBBER14-2710 CARBIDE TIP 20 TEETH 1” X 7/64” 4 THIN NON-FERROUS MATERIAL (TO APPROX . 1/8” THICK)14-2711 CARBIDE TIP 12 TEETH 1” X 7/64” 4 THICKER NON-FERROUS MATERIAL (TO APPROX . 1/2” THICK)Note; * *CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials.**Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.Saw Blades - oscillating saws with 3/8”arbor holeUsed on Cleco Dotco Oscillating Saw• Used on 12-22 SeriesMAXIMUM DEPTH OF CUT DIAMETER RECOMMENDED USEMODELDESCRIPTIONIN IN (GUIDELINES ONLY)14-1740* CARBIDE CHIP 36/80 GRIT 7/16” X 3/32” 2 FIBERGLASS14-1741* DIAMOND CHIP 40/60 GRIT 7/16” X 5/64” 2 FIBERGLASS, CARBON COMPOSITES14-1742 STAINLESS STEEL 124 TEETH 9/16” X 3/64” 2-1/2 WOOD, UNCURED OR CURED COMPOSITES, ALUMINUM, PLASTIC14-1743 CARBIDE 120 TEETH 9/16” X 1/16” 2-1/2 CURED GRAPHIC COMPOSITES14-1744 RAZOR 9/16” X 3/64” 2-1/2 CARDBOARD, LIGHT PLASTIC14-1745 STAINLESS STEEL 120 TEETH 9/16” X 3/64” 2-1/2 CONFINED SPACE14-1746 FLUSH STAINLESS 124 TEETH 9/16” X 3/64” 2-1/2 WOOD, UNCURED OR CURED COMPOSITES, ALUMINUM, PLASTIC14-1747 RAZOR 9/16” X 3/64” 3 CARDBOARD, LIGHT PLASTICUse only for sawing non-metallic materials. Note:230 CLECOTOOLS.COM
Specialty ToolsVacuum Conversion Kits 12-27 seriesConverts front exhaust to a one of the configurations shown below• Refer to the Vacuum Ready 12-27 Models in the catalogMODEL DESCRIPTION TOOL SERIES2704 OPTION 1 - PORTA BAG 12-272705 OPTION 2 - FLOOR BAG 12-272729 OPTION 3 - VACUUM SYSTEM ADAPTER 12-27To convert an existing Cleco Dotco front exhaust series 12-27 saw to Vacuum operation, order any of the conversion kits listed in the table. NOTE: When converting to vacuum, free speed of thetool will be reduced 20%.Vacuum Conversion Kits 12-42 seriesConverts front exhaust to a one of the configurations shown belowSpecialty Tools• Refer to the Vacuum Ready 12-42 Models in the catalogMODEL DESCRIPTION TOOL SERIES4131 OPTION 1 - PORTA BAG 12-424132 OPTION 2 - FLOOR BAG 12-424133 OPTION 3 - VACUUM SYSTEM ADAPTER 12-42To convert an existing Cleco Dotco front exhaust series 12-42 saw to Vacuum operation, order any of the conversion kits listed in the table. NOTE: When converting to vacuum, free speed of thetool will be reduced 20%.SC3A Series - Triple ScalerPiston Type• Piston Type• For maximum material removal• Heavy duty, rugged applicationMODELBORESTROKEAIR INLET SIZE LENGTH WEIGHT AIR INLET SIZEBLOWS PER MINUTEIN IN IN IN LB INSC3A 0.88 0.81 5200 3/8 13.3 7.9 3/8All tools performance rated @ 90psi / 620 kPa air pressure.Minimum Hose I.D.: 3/8in / 9.6mmStandard Equipment: Operating instructions & service manualCLECOTOOLS.COM231
- Page 179 and 180: GrindersMP44 Series Die Grinder20,0
- Page 181 and 182: Grinders10-11 Series - Extended - D
- Page 183 and 184: Grinders25 Series - Grinder - Exten
- Page 185 and 186: Grinders10LF Series - Die Grinder -
- Page 187 and 188: Grinders12-23 Series - Die Grinder
- Page 189 and 190: Grinders236 Series - Heavy Duty Hea
- Page 191 and 192: Grinders216 Series - Grinder - Exte
- Page 193 and 194: Grinders236 Series - Grinder - Righ
- Page 195 and 196: Grinders25 Series - Grinder - Exten
- Page 197 and 198: Grinders1700 Series - Horizontal Gr
- Page 199 and 200: GrindersCleco Wheel GuardsGrindersP
- Page 201 and 202: GrindersSeries HG Collets• For us
- Page 203 and 204: GrindersTermination 36 - Series 300
- Page 205 and 206: GrindersNoise Suppressor GuardFor u
- Page 207 and 208: Sanders & Polishers12LF Series - Sa
- Page 209 and 210: Sanders & Polishers12-13 Series - S
- Page 211 and 212: Sanders & Polishers10-27 & 12-27 Se
- Page 213 and 214: Sanders & Polishers12-23 Series - G
- Page 215 and 216: Sanders & PolishersSanding Belts -
- Page 217 and 218: Sanders & PolishersSave-A-Disc Pads
- Page 219 and 220: Specialty Tools12-12 Series - Right
- Page 221 and 222: Specialty Tools10-40 & 12-40 Series
- Page 223 and 224: Specialty ToolsRouter Guides For Ro
- Page 225 and 226: Specialty Tools10-43 Series Router
- Page 227 and 228: Specialty Tools12-22 Series - Right
- Page 229: Specialty ToolsSaw Blades - 1/4”
- Page 233 and 234: Specialty ToolsB1 Series - Push-Pul
- Page 235 and 236: Specialty Tools12-20 Series - Nibbl
- Page 237 and 238: AccessoriesAir Hoses - Cleco Dotco
- Page 239 and 240: AccessoriesActiveswivel Cleco Dotco
- Page 241 and 242: Solutions are in our DNA •CLECOTO
- Page 243 and 244: Drilling & RivetingSOLUTIONS ARE IN
- Page 245 and 246: Advanced DrillingCleco A Series: In
- Page 247 and 248: Advanced DrillingA1 Series - Positi
- Page 249 and 250: Advanced DrillingMODEL20962/962QB -
- Page 251 and 252: Advanced Drilling20802 - Positive F
- Page 253 and 254: Advanced DrillingPA/PB Series - Por
- Page 255 and 256: Advanced Drilling10Q Series - Porta
- Page 257 and 258: Hand Drilling, Countersinking & Spo
- Page 259 and 260: Hand Drilling, Countersinking & Spo
- Page 261 and 262: Hand Drilling, Countersinking & Spo
- Page 263 and 264: Hand Drilling, Countersinking & Spo
- Page 265 and 266: Hand Drilling, Countersinking & Spo
- Page 267 and 268: Hand Drilling, Countersinking & Spo
- Page 269 and 270: Hand Drilling, Countersinking & Spo
- Page 271 and 272: Hand Drilling, Countersinking & Spo
- Page 273 and 274: Hand Drilling, Countersinking & Spo
- Page 275 and 276: Hand Drilling, Countersinking & Spo
- Page 277 and 278: Hand Drilling, Countersinking & Spo
- Page 279 and 280: Hand Drilling, Countersinking & Spo
Specialty Tools
Saw Blades - 3/4” arbor hole
Used on Cleco Dotco Saw’s
• Used for sawing non-metallic materials
Specialty Tools
MODEL
DESCRIPTION
MAXIMUM DEPTH OF CUT DIAMETER RECOMMENDED USE
IN IN (GUIDELINES ONLY)
14-2690 DIAMOND CHIP 60/80 GRIT 1” X 5/64” 4 FIBERGLASS, COMPOSITE, CARBON FIBER
14-2694* CARBIDE CHIP 36 GRIT 1” X 11/64” 4 HARD RUBBER
14-2697* CARBIDE CHIP 80 GRIT 1” X 1/8” 4 FIBERGLASS
14-2699* CARBIDE TIP 20 TEETH 1” X 7/64” 4 THIN FIBERGLASS, PLASTIC LAMINATES TO 1/8” THICK
14-2700* CARBIDE TIP 20 TEETH 1” X 7/64” 4 THICKER FIBERGLASS, PLASTIC LAMINATES TO 1/2” THICK
14-2701* CARBIDE CHIP 36/80 GRIT 1” X 1/8” 4 FIBERGLASS, HARD RUBBER
14-2710 CARBIDE TIP 20 TEETH 1” X 7/64” 4 THIN NON-FERROUS MATERIAL (TO APPROX . 1/8” THICK)
14-2711 CARBIDE TIP 12 TEETH 1” X 7/64” 4 THICKER NON-FERROUS MATERIAL (TO APPROX . 1/2” THICK)
Note; * *CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials.
**Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
Saw Blades - oscillating saws with 3/8”
arbor hole
Used on Cleco Dotco Oscillating Saw
• Used on 12-22 Series
MAXIMUM DEPTH OF CUT DIAMETER RECOMMENDED USE
MODEL
DESCRIPTION
IN IN (GUIDELINES ONLY)
14-1740* CARBIDE CHIP 36/80 GRIT 7/16” X 3/32” 2 FIBERGLASS
14-1741* DIAMOND CHIP 40/60 GRIT 7/16” X 5/64” 2 FIBERGLASS, CARBON COMPOSITES
14-1742 STAINLESS STEEL 124 TEETH 9/16” X 3/64” 2-1/2 WOOD, UNCURED OR CURED COMPOSITES, ALUMINUM, PLASTIC
14-1743 CARBIDE 120 TEETH 9/16” X 1/16” 2-1/2 CURED GRAPHIC COMPOSITES
14-1744 RAZOR 9/16” X 3/64” 2-1/2 CARDBOARD, LIGHT PLASTIC
14-1745 STAINLESS STEEL 120 TEETH 9/16” X 3/64” 2-1/2 CONFINED SPACE
14-1746 FLUSH STAINLESS 124 TEETH 9/16” X 3/64” 2-1/2 WOOD, UNCURED OR CURED COMPOSITES, ALUMINUM, PLASTIC
14-1747 RAZOR 9/16” X 3/64” 3 CARDBOARD, LIGHT PLASTIC
Use only for sawing non-metallic materials. Note:
230 CLECOTOOLS.COM