Cleco-2019-full-catalog-v3-links

Air Motors
22 Series - Air Motor - Rotary Vane - Rear
Exhaust
Maximum Power 0.9 hp | 0.67 kw
• Maximum Power 0.9 hp | 0.67 kw
• Torque Range 0.8 - 41.2 ft. lbs. | 1.08 - 55.83 Nm
• Non-Reversible
• Rear Exhaust
MODEL MOUNT SPINDLE TYPE
22M5042-50
22M5340-50
22M5440-50
FLANGE AND BASE
MOUNTING
FLANGE AND BASE
MOUNTING
FLANGE AND BASE
MOUNTING
22-5040-50 ROUND
22-5041-50 ROUND
22-5042-50 ROUND
22-5340-50 ROUND
22-5940-50 ROUND
22M5940-50
FLANGE AND BASE
MOUNTING
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
1/2 IN KEYED
SPINDLE
RPM AT FREE TORQUE
AIR CON-
WEIGHT
LENGTH HORSEPOWER
MAX HP SPEED STALL
GEAR
SUMPTION
RATIO
R/MIN R/MIN FT LB | NM LB KG IN | MM HP SCFM
470 940
19.6 |
26.56
CONTROL
2.1 0.95 24-1 7.94 | 202 0.9 29 NON-REVERSIBLE
1600 3200 5.8 | 7.86 2.1 0.95 7.1-1 6.19 | 157 0.9 29 NON-REVERSIBLE
2350 4700 4.0 | 5.42 2.1 0.95 4.9-1 6.19 | 157 0.9 29 NON-REVERSIBLE
215 430
320 640
470 940
41.2 |
55.83
28.4 |
38.48
19.6 |
26.56
2.1 0.95 50.4-1 7.94 | 202 0.9 29 NON-REVERSIBLE
2.1 0.95 34.8-1 7.94 | 202 0.9 29 NON-REVERSIBLE
2.1 0.95 24-1 7.94 | 202 0.9 29 NON-REVERSIBLE
1600 3200 5.8 | 7.86 2.1 0.95 7.1-1 6.19 | 157 0.9 29 NON-REVERSIBLE
11500 23000 0.8 | 1.08 2.1 0.95 1-1 4.38 | 111 0.9 29 NON-REVERSIBLE
11500 23000 0.8 | 1.08 2.1 0.95 1-1 4.38 | 111 0.9 29 NON-REVERSIBLE
Air Inlet: 1/4” NPT – Side and rear
Air consumption: 29 cfm (.82 m3/min)
All tools performance rated @ 90psi (620 kPa) air pressure.
*Optional Terminations:
Replace -50 in model number with the desired termination when ordering.
-38 0”-1/4” Capacity Drill Chuck (5000 RPM or less)
-51 1/16”-3/8” Capacity Drill Chuck (5000 RPM or less)
-53 5/64”-1/2” Capacity Drill Chuck (5000 RPM or less)
-60 1/2”-20 Threaded Spindle
-01 Series 200 Collet Chuck (for milling and routing)
-62 Series “K” Collet Chuck (for milling and routing)
Standard Equipment:
Hex socket screw provided for closure of unused inlet. Flush fitting for lubrication of gears. Wrench for threaded spindle and collet chuck models. 1/4” collet included with series 200 & “K” collet
chuck.
Optional Equipment:
Any series 200 and “K” collet may be substituted at no additional cost.
**Please visit clecotools.com for dimensional diagrams and power curves.
Air Motors
132 CLECOTOOLS.COM