CS131 UL Certificate - Generex GmbH

RECOGNIZED COMPONENT 

Constructional Data Report (CDR) 

1.0 Reference and Address 

Report Number 1010969KAU-001 Original Issued: 28-May-2009 Revised: None 

Standard(s) 

UL Standard for Safety for Information Technology Equipment ANSI/ UL 60950-1 Issued: 

2007/03/27 Ed:2and 

CAN/ CSA C22.2 No. 60950-1 Issued:2007/03/01 Ed:2 

Applicant Generex Systems GmbH Manufacturer MSC Scotland Ltd 

Address 

Brunnenkoppel 3 

D-22041 Hamburg 

Address 

6 Bain Square 

Kirkton Campus 

Livingsgton EH54 7DQ 

Country Germany Country Scotland 

Contact Mr. Frank Blettenberger Contact Mr. Michael Page 

Phone +49 40 2269291-22 Phone +44 1506 407 404 

FAX +49 40 226 92 9110 FAX +44 1506 461 444 

Email frank@generex.de 

Email mpa@msc-ge.com 

Page 1 of 15

Report No. 1010969KAU-001 

Generex Systems GmbH 

2.0 Product Description 

Product 

Brand name 

Description Monitoring Device for UPS Systems 

Models 

Model Similarity 

Ratings 

Other Ratings 

Conditions of 

Acceptability 

CS124 Box, CS123 C-Box, CS124 Slot, CS123 Slot 

N/A 

9Vdc - 30Vdc, 100mA, 

N/A 

Page 2 of 15 Issued: 28-Mai-2009 

Revised: None 

Monitoring Device 

CS121L HW131, CS121BL HW131, CS121 SC HW131, CS121 BSC HW131 

The products covered in this Report are incomplete in construction features or limited in 

performance capabilities and are intended for use and evaluation in other products. 

Consideration should be given to the following when the component is used in or with another 

product. 

(Typical Conditions of Acceptability to be considered for recognized component products 

follow:) 

1. Suitability of the enclosure should be evaluated when installed in the end product. 

2. Temperature Testing should be performed on this component when installed in the end 

product. 

ED 16.3.15 (3/12/08) Informative



3.0 Product Photographs 

Photo 1 - External overview of model CS124 Box 

Photo 2 - Internal view of model CS124 Box 

03 

02 

04 


Revised: None 

05 

07 08 

06 

01 





Photo 3 - External overview of model CS123 

Photo 4 - Internal overview of model CS123 


Revised: None 

09 

10 

11 





Photo 5 - internal overview of CS123 and CS124 with supply over the platine 

Photo 6 - external overview of listed power supply 


Revised: None 

12 





Photo 7 - overview of marking plate 


Revised: None 

13 




4.0 Critical Components 

Photo # 

Item 

no. 1 

Name Manufacturer/ 

trademark 2 


Revised: None 

Type / model 2 Technical data and securement 

means 

1 1 Enclosure 

overalll dimension: 125.66mm x 64.73mm x 33.21mm. Mfr.Tekuma, 

UR 

type Staroy, min.HB 

2 2 RJ45 connector AMP 2-406549-4 Min. HB UR 

2 3 Signal LED Mentor LED 2mA NR 

2 4 PWB Generex CM M1 94V-0 UR 

2 5 Fuse Littelfuse Type 154 series 125V, 8A, 94V-0 UR 

2 6 

DC input 

connector 

Cliff DC10 12Vdc, 5A NR 

2 7 Dip switch Apem DA series 50Vdc, 100mA, 94V-0, UR 

2 8 SUB-D 9pol male Multicomp 

8LCM009P- 

301B 

min. HB, min. 105°C UR 

3 9 Enclosure Tekuma Staroy HB NR 

4 10 Ethernet 

connector 

Molex 95001-2661 min. HB UR 

4 11 Mini Din connector Assmann 

A-DIO-M/08 

min. HB UR 

6 12 Power supply Joden 3G72 

7 13 Marking label 3M 

7380, 7937, 

7866, 76799 

Input: 120Vac, 60Hz, 100mA 

Output: 12Vdc, 500mA 

for plastik material min 80°C, 

indoor use 

Mark(s) of 

conformity 3 

cULus 

NOTES: 

1) Not all item numbers are indicated (called out) in the photos, as their location is obvious. 

2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s) of 

conformity" can be used. 

3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted and only 

visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section 5.0 for 

details. 

UL 




5.0 Critical Unlisted CEC Components 

No Unlisted CEC components are used in this report. 


Revised: None 





Revised: None 

6.0 Critical Features 

Recognized Component - A component part, which has been previously evaluated by an accredited certification 

body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified 

by the Conditions of Acceptability. 

Listed Component - A component part, which has been previously Listed or Certified by an accredited 

Certification Organization with no restrictions and is used in the intended application within its ratings. 

Unlisted Component - A part that has not been previously evaluated to the appropriate designated component 

standard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing or 

component recognition. 

Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of a 

product that has a direct bearing on the product’s conformance to applicable requirements of the product 

standard. 

Construction Details - For specific construction details, reference should be made to the photographs and 

descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the 

specific construction details described in this Report, the following general requirements also apply. 

1. Spacing - Supplied with below 15VA, no spacings required. 

2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and display 

lamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or other 

mounting format that prevents turning of the component. 

3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or the 

equivalent. 

4. Accessibility of Live Parts - No accesibility live parts. 

5. Grounding - This product is not provided with a means of grounding as it is not required to be grounded 

since it is class II. 

6. Polarized Connection - none 

7. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads terminating 

in soldered connections are made mechanically secure prior to soldering. Recognized Component separable 

(quick disconnect) connectors of the positive detent type, closed loop connectors, or other types specifically 

described in the text of this report are also acceptable as internal wiring terminals. At points where internal 

wiring passes through metal walls or partitions, the wiring insulation is protected against abrasion or damage 

by plastic bushings or grommets. No internal wiring is provided. 

8. Schematics - none 

9. Markings - The product is marked with a labeling system as described in item no. 13 of Section 4.0 

as follows: manufacturer's name, brand name, model number, electrical ratings.. 

The following markings in French are required: none 

10. Cautionary Markings - The following are required: none 

11. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are 

provided by the manufacturer. 




7.0 Illustrations 

Illustration 1 - Marking label of CS 124 

Illustration 2 - Marking label of CS 123 


Revised: None 




BASIC LISTEE 

Address 

Country 

Product 

MULTIPLE LISTEE 1 

Address 

Country 

Brand Name 

ASSOCIATED 

MANUFACTURER 

Address 

Country 


Address 

Country 

Brand Name 

ASSOCIATED 

MANUFACTURER 

Address 

Country 


Revised: None 

9.0 Correlation Page For Multiple Listings 

The following products, which are identical to those identified in this report except for model number and Listee 

name, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program. 


Address 

Country 

Brand Name 

ASSOCIATED 

MANUFACTURER 

Address 

Country 


Brunnenkoppel 3 

D-22041 Hamburg 

Germany 

Monitoring Device 

None 

MULTIPLE LISTEE 1 MODELS 

None 


None 


BASIC LISTEE MODELS 







Revised: None 

10.0 General Information 

The Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance with 

the requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorization 

prior to using alternate parts, components or materials. 

COMPONENTS 

Components used shall be those itemized in this Intertek report covering the product, including any amendments 

and/or revisions. 

LISTING MARK 

The ETL Listing mark applied to the products shall either be separable in form, such as labels purchased from 

Intertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is 

subject to the control of Intertek. 

MANUFACTURING AND PRODUCTION TESTS 

Manufacturing and Production Tests shall be performed as required in this Report. 

FOLLOW UP SERVICE 

Periodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shall be 

scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to the 

following: 

1. Conformance of the manufactured product to the descriptions in this Report. 

2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification Agreement. 

3. Manufacturing changes. 

4. Performance of specified Manufacturing and Production Tests. 

In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, the 

Applicant shall take one or more of the following actions: 

1. Correct the non-conformance. 

2. Remove the ETL Mark from non-conforming product. 

3. Contact the issuing product safety evaluation center for instructions. 

10.1 Evaluation of Unlisted Components 

Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program, Intertek 

may require these components to be tested and/or evaluated at least once annually, more often for certain 

components, as part of the independent certification process. The Unlisted Components in Section 5.0 require 

Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writing 

when these components must be selected and sent to the CEC for re-evaluation 

Ship the samples to: 

Intertek Deutschland GmbH 

ETL Component Evaluation Center 

Innovapark 20 

D-87600 Kaufbeuren,Germany 

Sample Disposition: Due to the destructive nature of the testing, all samples will be 

discarded at the conclusion of testing unless, the manufacturer specifically requests the 

return of the samples. The request for return must accompany the initial component 

shipment. 




Required Tests 

none 


Revised: None 

11.0 Manufacturing and Production Tests 

The manufacturer agrees to conduct the following Manufacturing and Production Tests as specified: 




12.0 Revision Summary 

The following changes are incompliance with the declaration of Section 8.1: 

Date/ Project Handler/ 

Proj # Site ID Reviewer 

Section Item Description of Change 

None 


Revised: None

CS131 UL Certificate - Generex GmbH

Create successful ePaper yourself

Delete template?

Save as template?