User´s Manual - I+ME ACTIA GmbH

More documents

Recommendations

Info

CAT Diagnostic Setup Attention: It is highly recommended not to manipulate any files of CAT software e.g. by the use of an editor. The following is highly recommended to be done only by experienced PC users. Professional users of the diagnostic features of CAT may need to change the diagnostic parameters defining the handling of diagnostic frames. Therefore an editor has to be used to change the default settings in CAT.INI file. The file CAT.INI is located in the folder "CAT_Destination_Folder"\BIN. (CAT_Destination_Folder is the folder that have been chosen when installing CAT) Block Size The PCI (Protocol Control Interface) parameter RespFlowCtrl_Bsmax (is set to 5 in sample above). The BS (Block Size) defines the maximum number of frames which can be send before another flow control frame has to be sent. Separation Time The PCI (Protocol Control Interface) parameter RespFlowCtrl_STmin (is set to 100 ms in sample above). The ST (Separation Time) defines the minimum amount of time in ms that must be between consecutive frame transmissions of a multi frame message. Padding The PCI (Protocol Control Interface) parameters PaddingSWC, PaddingMS, PaddingHS (all are set to 0 in sample above meaning No Padding). Padding means to fill up the Data Byte Field of the CAN Frames with 0's, so that the frames always contain 8 Data Bytes. Set parameter PaddingSWC to 1 to have padding for the Single Wire CAN (SWC), when Single Wire CAN has been chosen as physical layer in the CAN Setup . Set parameter PaddingMS to 1 to have padding for the Dual Wire CAN Mid Speed (MS), when Dual Wire CAN Mid Speed has been chosen as physical layer in the CAN Setup . Set parameter PaddingHS to 1 to have padding for the Dual Wire CAN High Speed (HS), when Dual Wire CAN High Speed has been chosen as physical layer in the CAN Setup . Note: Padding -when activated- is only done for the frames send out by diagnostic services but not for frames set up in the Transmission table. 60
Offline CAN Acknowledge The Firmware parameter OfflineWithCANBusOn (is set to 1 in sample above meaning activated). CAT is able to acknowledge CAN traffic even when being Offline respectively Diagnostic Offline. This is especially then useful when CAT communicates only to one single ECU (CAN node). This behavior can be switched off to have no impact to a CAN network when CAT is Offline. Set parameter OfflineWithCANBusOn to 1 to have CAN acknowledgement even in (Diagnostic) Offline mode. Set parameter OfflineWithCANBusOn to 0 to have no CAN acknowledgement in (Diagnostic) Offline. 61
Page 1 and 2:
CAT 2.0 CAN ANALYZER TOOL User´s M
Page 3 and 4:
Our six products groups are: 1 CAN
Page 5 and 6:
Table of Contents Introduction 4 In
Page 7 and 8:
Diagnostic Offline Analyzing 186 Di
Page 9 and 10:
Introduction The I+ME CAT (CAN Anal
Page 11 and 12:
About I+ME ACTIA The company... On
Page 13 and 14: System Requirements The host PC has
Page 15: Installation Note: It does not matt
Page 18 and 19: Re-Install Before Re-Installing CAT
Page 20 and 21: Terms & Phrases Block Size (BS) The
Page 22 and 23: Application Structure CAT can recog
Page 24 and 25: Online Mode The Online Mode of CAT
Page 26 and 27: In Offline mode the user can export
Page 28 and 29: Diagnostic Offline Mode In general
Page 30: Main Window The main window after o
Page 34 and 35: Frame List View The Frame List show
Page 36 and 37: Trace List View Different to the Fr
Page 39 and 40: Diagnostic Online View The Diagnost
Page 41 and 42: Transmit Table Online Control windo
Page 43 and 44: Online Diagnostic Launch The settin
Page 45 and 46: Download Information Window The Dow
Page 47 and 48: Hardware 43
Page 49 and 50: LED Interpretation Normal States: 1
Page 51 and 52: Basic Steps After successful instal
Page 53 and 54: Being Offline Choose menu item Comm
Page 55 and 56: Being Diagnostic Online Choose menu
Page 57 and 58: Configure Transmit Conditions: Up t
Page 59 and 60: Session Management The following is
Page 61 and 62: Database Management The following i
Page 63: ECU Template The following is highl
Page 67 and 68: Offline Setup 63
Page 69 and 70: Session Menu The following screensh
Page 71 and 72: Session Description Using the assig
Page 73 and 74: Save as Using the assigned Session
Page 75 and 76: Export logging buffer Using the ass
Page 77 and 78: Export Read Data by ID The diagnost
Page 79 and 80: Database Maintaining 75
Page 81 and 82: Vehicle CAT allows the user to edit
Page 83 and 84: See also Diagnostics Configuration
Page 86 and 87: Signal CAT allows the user to edit
Page 88 and 89: Signal Types 84
Page 90 and 91: Boolean CAT allows the user to edit
Page 92 and 93: Bitmap Table Bitmap Definition Tabl
Page 94 and 95: Marks one Byte as an Embedded Ident
Page 96 and 97: Embedded ID Marks one Byte as an Em
Page 102 and 103: State Encoded Value Table Value Def
Page 108 and 109: CPID Table CAT provides two differe
Page 110 and 111: CAT allows editing or removing of a
Page 112 and 113: The first data byte (Byte 0) of the
Page 114 and 115:
110
Page 116 and 117:
112
Page 118 and 119:
114
Page 120 and 121:
Filter List CAT allows defining 10
Page 122 and 123:
Filter Definition After choosing a
Page 124 and 125:
Transmit List CAT allows defining 1
Page 126 and 127:
Note: This field is only enabled if
Page 128 and 129:
Example: Trigger conditions are ID
Page 130 and 131:
Diagnostics CAT allows setup and ad
Page 132 and 133:
The Definition buttons allow additi
Page 134 and 135:
Read Trouble Codes This service ($A
Page 136 and 137:
History DTC A history DTC indicates
Page 138 and 139:
Read Failure Record Parameters The
Page 140 and 141:
Read Data by Identifier The purpose
Page 142 and 143:
Import Use the import button to re-
Page 144 and 145:
Request for one-shot response messa
Page 146 and 147:
Device Control The purpose of the s
Page 148 and 149:
Device Control Reset The purpose of
Page 150 and 151:
Security access - send key The purp
Page 152 and 153:
Initiate Diagnostic Operation This
Page 154 and 155:
Return to Normal Mode The purpose o
Page 156 and 157:
Frame List CAT allows the user to s
Page 158 and 159:
Choose menu item Configurations | S
Page 160 and 161:
Layout Settings To adopt the Layout
Page 162 and 163:
158
Page 164 and 165:
Scrolling Step Size To scroll more
Page 166 and 167:
CAN Setup CAT supports normal "Dual
Page 168 and 169:
Buffer Setup The complete 50,000-fr
Page 170 and 171:
Changing CAT Modes CAT can be used
Page 172 and 173:
Filtering CAT allows defining 10 di
Page 174 and 175:
If Transmit Table is closed choose
Page 176 and 177:
Launch Diagnostic Services Choose m
Page 178 and 179:
Diagnostic Online Mode 174
Page 180 and 181:
Diagnostic Online Filtering The Dia
Page 182 and 183:
Offline Analyzing 178
Page 184 and 185:
Error Interpretation The status bar
Page 186 and 187:
Buffer Handling CAT uses the serial
Page 188 and 189:
Find It CAT provides a search comma
Page 190 and 191:
Diagnostic Offline Analyzing 186
Page 192 and 193:
Tips & Tricks 188
Page 194 and 195:
FAQ Installation If there is a ques
Page 196 and 197:
FAQ Online Mode Bus Status : Error
Page 198 and 199:
FAQ Offline Analyzing If there is a
Page 200 and 201:
Index A About I+ME ACTIA ..........
Page 202 and 203:
Initiate Diagnostic Operation......
show all

User´s Manual - I+ME ACTIA GmbH

Create successful ePaper yourself

Delete template?

Save as template?