- Page 1 and 2: CAT 2.0 CAN ANALYZER TOOL User´s M
- Page 3 and 4: Our six products groups are: 1 CAN
- Page 5 and 6: Table of Contents Introduction 4 In
- Page 7 and 8: Diagnostic Offline Analyzing 186 Di
- Page 9 and 10: Introduction The I+ME CAT (CAN Anal
- Page 11 and 12: About I+ME ACTIA The company... On
- Page 13 and 14: System Requirements The host PC has
- Page 15: Installation Note: It does not matt
- Page 19 and 20: System Overview 15
- Page 21 and 22: Software 17
- Page 23 and 24: ! If the user disconnects the Hardw
- Page 25 and 26: Offline Mode The Offline Mode of CA
- Page 27 and 28: Diagnostic Online Mode The Diagnost
- Page 29 and 30: Windows 25
- Page 32: Status Bar The Status Bar shown bel
- Page 35 and 36: Signal List View The Signal List sh
- Page 37: Diagnostic Output The Diagnostic Ou
- Page 40 and 41: Online Control Windows 36
- Page 42 and 43: Main Diagnostic Launch Table Online
- Page 44 and 45: Status Information Windows Status I
- Page 46 and 47: Upload Information Window The Uploa
- Page 48 and 49: Hardware System Structure CAT Hardw
- Page 50 and 51: Getting Started 46
- Page 52 and 53: Being Online Choose menu item Comma
- Page 54 and 55: Up to 10 Transmit Frames can be con
- Page 56 and 57: Being Diagnostic Offline In general
- Page 58 and 59: File Management 54
- Page 60 and 61: Session Template The following is h
- Page 62 and 63: Database Template The following is
- Page 64 and 65: CAT Diagnostic Setup Attention: It
- Page 66 and 67:
Diagnostic Data by ID Edit The foll
- Page 68 and 69:
Session Handling 64
- Page 70 and 71:
Create a new Session Using the assi
- Page 72 and 73:
Open a Session Using the assigned S
- Page 74 and 75:
Close Session Shuts down the actual
- Page 76 and 77:
Export Diagnostic Buffer Using the
- Page 78 and 79:
Exit Shuts down CAT windows applica
- Page 80 and 81:
Database CAT allows editing or dele
- Page 82 and 83:
ECU CAT allows the user to edit or
- Page 84:
Frame CAT allows the user to edit o
- Page 87 and 88:
Remove Signal Choose menu item Conf
- Page 89 and 90:
Data Byte/Bit Presentation on the C
- Page 91 and 92:
Embedded ID Marks one Byte as an Em
- Page 93 and 94:
Engineering Note: The Signal (Data)
- Page 95 and 96:
Packed Binary Coded Decimal CAT all
- Page 97 and 98:
Signed Integer Note: The Signal (Da
- Page 99 and 100:
State Encoded Value Note: The Signa
- Page 101 and 102:
State Encode Value Table Table Defi
- Page 103 and 104:
String Note: The Signal (Data) Type
- Page 105 and 106:
Unsigned Integer Note: The Signal (
- Page 107 and 108:
Diagnostic Data 103
- Page 109 and 110:
DPID List CAT allows editing or rem
- Page 111 and 112:
DPID Signals CAT is able to interpr
- Page 113 and 114:
FSA List CAT allows editing or remo
- Page 115 and 116:
DTC List CAT allows editing or remo
- Page 117 and 118:
DID List CAT allows editing or remo
- Page 119 and 120:
Configurations 115
- Page 121 and 122:
Click on OK to acknowledge the inpu
- Page 123 and 124:
Click on OK to acknowledge the inpu
- Page 125 and 126:
Transmit Definition After choosing
- Page 127 and 128:
Trigger CAT allows defining a Trigg
- Page 129 and 130:
Trigger on existing Frames When the
- Page 131 and 132:
Physical Addressing Put in the Diag
- Page 133 and 134:
Diagnostic Services 129
- Page 135 and 136:
needs to select a mask. By click on
- Page 137 and 138:
Read Failure Record Identifier The
- Page 139 and 140:
Clear Trouble Codes The Clear Troub
- Page 141 and 142:
Write Data by Identifier The purpos
- Page 143 and 144:
Read Data by Packet Identifier The
- Page 145 and 146:
Read Memory by Address The purpose
- Page 147 and 148:
If an ECU has been addressed that i
- Page 149 and 150:
Security Access - request seed The
- Page 151 and 152:
Tester Present This service ($3E) i
- Page 153 and 154:
Disable Normal Communication The pu
- Page 155 and 156:
Layout Setup 151
- Page 157 and 158:
Signal List CAT allows the user to
- Page 159 and 160:
Windows Arrangement CAT provides di
- Page 161 and 162:
CAT allows the user to define for e
- Page 163 and 164:
Change Language CAT is bilingual. T
- Page 165 and 166:
System Setup 161
- Page 167 and 168:
The CAN Setup window above shows ho
- Page 169 and 170:
Online Mode 165
- Page 171 and 172:
Online Analyzing Choose menu item C
- Page 173 and 174:
Transmitting CAT allows defining 10
- Page 175 and 176:
Triggering CAT allows defining a Tr
- Page 177 and 178:
CAT sends out the tester present se
- Page 179 and 180:
Diagnostic Online Analyzing Choose
- Page 181 and 182:
Launch Service Diagnostic Online Ch
- Page 183 and 184:
Offline Analyzer Mode Choose menu i
- Page 185 and 186:
ECC: CAT reads out The Error Code C
- Page 187 and 188:
Note: There is no visible scrolling
- Page 189 and 190:
Note: But you don't have to close t
- Page 191 and 192:
Diagnostic Offline Window In genera
- Page 193 and 194:
Hot Keys Implemented Hot Keys: Note
- Page 195 and 196:
FAQ Offline Setup 64 bit UNM Unsign
- Page 197 and 198:
FAQ Diagnostic Online Mode If there
- Page 199 and 200:
FAQ Diagnostic Offline Analyzing If
- Page 201 and 202:
Device Control ....................
- Page 203:
State Encode Value Table ..........