User´s Manual - I+ME ACTIA GmbH

More documents

Recommendations

Info

Return to Normal Mode The purpose of this service ($20) is to return a node or group of nodes to normal mode operation by canceling all active diagnostic services and resetting normal message communications (if they were interrupted by a diagnostic operation). The service Return to Normal Mode does not need / allow any setup. 150
Layout Setup 151
Page 1 and 2:
CAT 2.0 CAN ANALYZER TOOL User´s M
Page 3 and 4:
Our six products groups are: 1 CAN
Page 5 and 6:
Table of Contents Introduction 4 In
Page 7 and 8:
Diagnostic Offline Analyzing 186 Di
Page 9 and 10:
Introduction The I+ME CAT (CAN Anal
Page 11 and 12:
About I+ME ACTIA The company... On
Page 13 and 14:
System Requirements The host PC has
Page 15:
Installation Note: It does not matt
Page 18 and 19:
Re-Install Before Re-Installing CAT
Page 20 and 21:
Terms & Phrases Block Size (BS) The
Page 22 and 23:
Application Structure CAT can recog
Page 24 and 25:
Online Mode The Online Mode of CAT
Page 26 and 27:
In Offline mode the user can export
Page 28 and 29:
Diagnostic Offline Mode In general
Page 30:
Main Window The main window after o
Page 34 and 35:
Frame List View The Frame List show
Page 36 and 37:
Trace List View Different to the Fr
Page 39 and 40:
Diagnostic Online View The Diagnost
Page 41 and 42:
Transmit Table Online Control windo
Page 43 and 44:
Online Diagnostic Launch The settin
Page 45 and 46:
Download Information Window The Dow
Page 47 and 48:
Hardware 43
Page 49 and 50:
LED Interpretation Normal States: 1
Page 51 and 52:
Basic Steps After successful instal
Page 53 and 54:
Being Offline Choose menu item Comm
Page 55 and 56:
Being Diagnostic Online Choose menu
Page 57 and 58:
Configure Transmit Conditions: Up t
Page 59 and 60:
Session Management The following is
Page 61 and 62:
Database Management The following i
Page 63 and 64:
ECU Template The following is highl
Page 65 and 66:
Offline CAN Acknowledge The Firmwar
Page 67 and 68:
Offline Setup 63
Page 69 and 70:
Session Menu The following screensh
Page 71 and 72:
Session Description Using the assig
Page 73 and 74:
Save as Using the assigned Session
Page 75 and 76:
Export logging buffer Using the ass
Page 77 and 78:
Export Read Data by ID The diagnost
Page 79 and 80:
Database Maintaining 75
Page 81 and 82:
Vehicle CAT allows the user to edit
Page 83 and 84:
See also Diagnostics Configuration
Page 86 and 87:
Signal CAT allows the user to edit
Page 88 and 89:
Signal Types 84
Page 90 and 91:
Boolean CAT allows the user to edit
Page 92 and 93:
Bitmap Table Bitmap Definition Tabl
Page 94 and 95:
Marks one Byte as an Embedded Ident
Page 96 and 97:
Embedded ID Marks one Byte as an Em
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
State Encoded Value Table Value Def
Page 104 and 105: Embedded ID Marks one Byte as an Em
Page 106 and 107: Embedded ID Marks one Byte as an Em
Page 108 and 109: CPID Table CAT provides two differe
Page 110 and 111: CAT allows editing or removing of a
Page 112 and 113: The first data byte (Byte 0) of the
Page 114 and 115: 110
Page 116 and 117: 112
Page 118 and 119: 114
Page 120 and 121: Filter List CAT allows defining 10
Page 122 and 123: Filter Definition After choosing a
Page 124 and 125: Transmit List CAT allows defining 1
Page 126 and 127: Note: This field is only enabled if
Page 128 and 129: Example: Trigger conditions are ID
Page 130 and 131: Diagnostics CAT allows setup and ad
Page 132 and 133: The Definition buttons allow additi
Page 134 and 135: Read Trouble Codes This service ($A
Page 136 and 137: History DTC A history DTC indicates
Page 138 and 139: Read Failure Record Parameters The
Page 140 and 141: Read Data by Identifier The purpose
Page 142 and 143: Import Use the import button to re-
Page 144 and 145: Request for one-shot response messa
Page 146 and 147: Device Control The purpose of the s
Page 148 and 149: Device Control Reset The purpose of
Page 150 and 151: Security access - send key The purp
Page 152 and 153: Initiate Diagnostic Operation This
Page 156 and 157: Frame List CAT allows the user to s
Page 158 and 159: Choose menu item Configurations | S
Page 160 and 161: Layout Settings To adopt the Layout
Page 162 and 163: 158
Page 164 and 165: Scrolling Step Size To scroll more
Page 166 and 167: CAN Setup CAT supports normal "Dual
Page 168 and 169: Buffer Setup The complete 50,000-fr
Page 170 and 171: Changing CAT Modes CAT can be used
Page 172 and 173: Filtering CAT allows defining 10 di
Page 174 and 175: If Transmit Table is closed choose
Page 176 and 177: Launch Diagnostic Services Choose m
Page 178 and 179: Diagnostic Online Mode 174
Page 180 and 181: Diagnostic Online Filtering The Dia
Page 182 and 183: Offline Analyzing 178
Page 184 and 185: Error Interpretation The status bar
Page 186 and 187: Buffer Handling CAT uses the serial
Page 188 and 189: Find It CAT provides a search comma
Page 190 and 191: Diagnostic Offline Analyzing 186
Page 192 and 193: Tips & Tricks 188
Page 194 and 195: FAQ Installation If there is a ques
Page 196 and 197: FAQ Online Mode Bus Status : Error
Page 198 and 199: FAQ Offline Analyzing If there is a
Page 200 and 201: Index A About I+ME ACTIA ..........
Page 202 and 203: Initiate Diagnostic Operation......
show all

User´s Manual - I+ME ACTIA GmbH

Create successful ePaper yourself

Delete template?

Save as template?