Weidmueller Heavy Duty Connectors

Technical data
Using wire-end ferrules
Overview
A
Type of connection Series HA HE HVE HSB
Screw Clamping range [mm 2 ] 0.5 – 2.5 0.5 – 2.5 0.5 – 2.5 –
Clamping range [AWG] 20 – 12 20 – 14 (12) 1) 20 – 14 (12) 1) –
Ferrules with collars H0.5/14 – H2.5/14 H0.5/14 – H2.5/14 2) H0.5/14 – H2.5/14 2) –
H0.5/16 – H2.5/16 H0.5/16 – H2.5/16 2) H0.5/16 – H2.5/16 2)
Ferrules without collars H0.5/10 – H2.5/10 H0.5/10 – H2.5/10 H0.5/10 – H2.5/10 –
Twin wire-end ferrules
with collars
H0.5/16.5 (ZH) H0.5/18.5 (ZH) – H0.5/15 (ZH)
H0.5/18.5 (ZH) H1.0/20 (ZH) 3) H0.5/16.5 (ZH)
H0.75/17 (ZH) H1.5/20 (ZH) 3) H0.5/18.5 (ZH)
H1.0/20 (ZH)
H0.75/15 (ZH)
H1.5/20 (ZH)
H0.75/17 (ZH)
H1.0/15 (ZH)
H1.0/20 (ZH)
H1.5/16 (ZH)
H1.5/20 (ZH)
H2.5/18.5 (ZH)
Crimp tool PZ4 2) , PZ6, PZ6/5 PZ4 2) , PZ6, PZ6/5 PZ4 2) , PZ6, PZ6/5 –
PZ6 Hex 2) PZ6 Hex 2)
Screwdriver SDK PH0 SDK PH0 SDK PH0 –
SD 0.5x 3.0 SD 0.5x 3.0 SD 0.5x 3.0
Tightening torque 0.5 Nm 0.5 Nm 0.5 Nm –
Tension clamp Clamping range [mm 2 ] 0.25 – 1.5 0.25 – 2.5 0.25 – 2.5 –
2.5 solid core
Clamping range [AWG] 24 – 14 4) 24 – 14 24 – 14 –
Ferrules with collars H0.5/14 – H1.5/14 4) H0.5/14 – H2.5/14 2) H0.5/14 – H2.5/14 2) –
H0.5/16 – H1.5/16 4)
Ferrules without collars H0.5/10 – H1.5/10 4) – – –
Twin wire-end ferrules
with collars
– H0.5/15 (ZH) 5) or 6) – –
H0.75/15 (ZH) 5) or 6)
H1.0/15 (ZH) 5) or 6)
H1.5/16 (ZH) 5) or 6)
Crimp tool PZ4, PZ6, PZ6/5 PZ4 7) , PZ6, PZ6/5 PZ4 7) , PZ6, PZ6/5 –
Screwdriver SD 0.5x 3.0 SD 0.6x 3.5 SD 0.6x 3.5 –
PUSH IN Clamping range [mm 2 ] – solid 0.5 – 4 mm 2 – –
flexible with ferrule
0.5 – 2.5 mm 2
Clamping range [mm 2 ] – 20 – 12 – –
Ferrules with collars – H0.5/14 – H1.5/14 – –
– H0.5/16 – H1.5/16 – –
– H0.75/18 – H2.5/18 2) – –
Ferrules without collars – H0.5/10 – H2.5/10 2) – –
– H1.5/12 – H2.5/12 2) – –
Twin wire-end ferrules
with collars
– H0.5/18.4 ZH 500 V / 6 kV / 3 – –
H1/20 ZH 400 V / 6 kV / 3
500 V / 6 kV / 3 only with protection degree of at least IP54
H1.5/20 ZH 400 V / 6 kV / 3
500 V / 6 kV / 3 only with protection degree of at least IP54
Ferrules crimped with – PZ4. PZ6. PZ6/5. – –
PZ6 Hex
PE contact Clamping range [mm 2 ] 0.5 – 4.0 0.5 – 4 0.5 – 4 –
0.5 – 2.5 flexible
Clamping range [AWG] 20 – 12 20 – 12 20 – 12 –
Ferrules with collars H0.5/16 – H2.5/16 H0.5/16 – H4/16 H0.5/16 – H4/16 –
Ferrules without collars H0.5/10 – H2.5/10 H0.5/10 – H4/10 H0.5/10 – H4/10 –
Ferrules crimped with PZ4 2) , PZ6, PZ6/5 PZ4, PZ6, PZ6/5, PZ4, PZ6, PZ6/5, –
PZ6 Hex
PZ6 Hex
Screwdriver PH 1 PH 1 PH 1 –
Tightening torque 1.2 Nm 1.2 Nm 1.2 Nm –
1)
Depending on the diameter of the insulation, the max. AWG wire may need to be pushed in with some force.
2)
The 2.5mm 2 wire must be inserted with some force.
3)
When the rated voltage is reduced to 400 V / 6 kV / 3 or with a protection degree of at least IP54.
4)
Only by tilting the screwdriver can the clamping point be opened all the way.
5)
Wire-end ferrules may be used when the rated voltage is reduced to 400 V / 6 kV / 3.
6)
When the protection degree is at least IP54, the creepage and clearance distances within the encapsulation may
be rated for a lower pollution degree (DIN EN 61984). For this encapsulation, the use of wire-end ferrules is
possible with 500 V / 6 kV / 3.
7)
The PZ4 crimping tool should not be used with the max. wire size.
The connector inserts can be combined with wire-end ferrules in other ways depending on the available clamping range and the type of cable being used.
We would be happy to take a look at the technical feasibility of your specific application.
A.16 2028800000