TITAN TTL530GBC PETROL MULTI TOOL 61145
TITAN TTL530GBC PETROL MULTI TOOL USER MANUAL TITAN TTL530GBC PETROL MULTI TOOL USER MANUAL
6. Let the petrol brush cutter run in idle speed for 10-15s to let it warm up. 7.Depress throttle interlock (21) and then depress throttle trigger (24) to get full engine speed for operation. STARTING WARM ENGINE 1. Set ignition switch(22) to “I” position(Fig.15). 2. Move choke lever to “WARM START” position, do not depress primer bulb. 3.Depress throttle interlock(21) and then depress throttle trigger(24), and press this throttle safety button(23) to lock it in half-gas position of throttle trigger(24). Once the throttle safety button(23) is located, then release throttle interlock(21) and throttle trigger(24) synchronously(Fig.13). 22 Fig.15 21 23 24 Fig.18 4. Pull the recoil starter to start engine. Now, your brush cutter is under idle-speed states. 5. Depress throttle interlock (21) and then depress throttle trigger (24) to get full engine speed for operation.
STOPPING ENGINE WARNING! The cutting means will continue to rotate for some time even after the engine has been switched off! Wait until they come to a complete stop before you place down the petrol brush cutter and grass trimmer! 1. Release throttle interlock(21) and throttle trigger(24) to return to idle before shutting off engine(Fig.19). 22 21 23 24 Fig.19 2. Set ignition switch to “STOP” position to shut off engine(Fig.20). CUTTING Fig.20 WARNING! To avoid hazards never cut vegetation with a thickness of more than 20mm! Avoid contact with stones, metal materials, glass and so on! Inspect the blade regularly for damages, cracks or breaks! Never use a damaged blade! WARNING! When working with the cutting blade there is always a risk of kickback if the cutting means come into contact with hard objects! A kickback will cause sudden stalling of the cutting means which in turn causes the uncontrolled petrol brush cutter and grass trimmer to be forced in the direction opposite of the cutting means' rotation at the point of the binding! Therefore keep handles clean and free from greasy substances, and pay attention to firm stand to avoid injuries! 1. Use the cutting blade and guard to cut weeds, brush, small trees and similar vegetation with a thickness of up to 20 mm. 2. Never hold the unit higher than your hip. Work cautiously. The higher you hold the unit the bigger is the risk of thrown objects or clippings(Fig.21). 43CC PETROL BRUSH CUTTER TTL530GBC
- Page 1 and 2: 1 SAFETY AND OPERATING MANUAL Origi
- Page 3 and 4: SAFETY INSTRUCTIONS Warnings! Read
- Page 5 and 6: 11. Stop using the product while pe
- Page 7 and 8: 2. Stop the engine and unplug the s
- Page 9 and 10: Health Surveillance. All employees
- Page 11 and 12: Risk of fire / flammable materials
- Page 13 and 14: A 15 1 13 13a 19 14 20 18 17 22 3 2
- Page 15 and 16: A. Main unit 1. Engine 2. Upper sha
- Page 17 and 18: ACCESSORIES Torx screw driver (T25)
- Page 19 and 20: 2. Assembling shaft. 1). Align the
- Page 21 and 22: Ensure that there are no open flame
- Page 23: Operation instruction WARNING! For
- Page 27 and 28: Fig.24 TIPS 1. For best results, do
- Page 29 and 30: AIR FILTER 1. Inspect the air filte
- Page 31 and 32: Fig.29 4. To replace the spool simp
- Page 33 and 34: Troubleshooting Problem Possible ca
STOPPING ENGINE<br />
WARNING! The cutting means will continue to rotate for some time even after the<br />
engine has been switched off! Wait until they come to a complete stop before you<br />
place down the petrol brush cutter and grass trimmer!<br />
1. Release throttle interlock(21) and throttle trigger(24) to return to idle before shutting off<br />
engine(Fig.19).<br />
22<br />
21<br />
23<br />
24<br />
Fig.19<br />
2. Set ignition switch to “STOP” position to shut off engine(Fig.20).<br />
CUTTING<br />
Fig.20<br />
WARNING! To avoid hazards never cut vegetation with a thickness of more than<br />
20mm! Avoid contact with stones, metal materials, glass and so on! Inspect the<br />
blade regularly for damages, cracks or breaks! Never use a damaged blade!<br />
WARNING! When working with the cutting blade there is always a risk of kickback<br />
if the cutting means come into contact with hard objects! A kickback will cause<br />
sudden stalling of the cutting means which in turn causes the uncontrolled<br />
petrol brush cutter and grass trimmer to be forced in the direction opposite of the<br />
cutting means' rotation at the point of the binding! Therefore keep handles clean<br />
and free from greasy substances, and pay attention to firm stand to avoid<br />
injuries!<br />
1. Use the cutting blade and guard to cut weeds, brush, small trees and similar vegetation with<br />
a thickness of up to 20 mm.<br />
2. Never hold the unit higher than your hip. Work cautiously. The higher you hold the unit the<br />
bigger is the risk of thrown objects or clippings(Fig.21).<br />
43CC <strong>PETROL</strong> BRUSH CUTTER <strong>TTL530GBC</strong>