TITAN TTL530GBC PETROL MULTI TOOL 61145
TITAN TTL530GBC PETROL MULTI TOOL USER MANUAL TITAN TTL530GBC PETROL MULTI TOOL USER MANUAL
Fitting and adjusting the harness WARNING! Always attach the product to the harness. Do not carry it just by hand! 1). Remove the harness from the loop, open the securing clip(37). 2). Place the harness(38) so that is runs over the left shoulder, crossing the chest and back. The securing must be located at the right hip(Fig.12). 3). Adjust the length of the harness so that the hook is approximately 15cm below your waist; locate the product to the harness by using the securing clip (36) that the angle of the cutting head is parallel to the surface being cut(Fig.13). Fig.12 Fig.13 4). In case of emergency, pull the rope of the quick release mechanism. The metal locking bar will be released from the harness(37) automatically by opening the securing clip(36) because of the weight of the machine, and the machine will drop away from you(Fig.14). 37 36 12 Fig.14
Operation instruction WARNING! For your safety, please read carefully the safety warnings before operate the brush cutter! STARTING COOLING ENGINE 1. Place the petrol brush cutter on a flat stable ground that is not flammable. Ensure that the cutting means to not touch any objects or the ground. 2. Set ignition switch(22) to “I” position(Fig.15). Fig.15 3. Move choke lever(20) to “COLD START” position and pump primer bulb(18) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 6 times(Fig.16). 20 18 14 4.Depress throttle interlock(21) and then depress throttle trigger(24), and press this throttle safety button(23) to lock it in half-gas position of throttle trigger(24). Once the throttle safety button(23) is located, then release throttle interlock(21) and throttle trigger(24) synchronously(Fig.17). 22 Fig.16 21 23 24 Fig.17 5. Pull the recoil starter to start engine and then move choke lever to "WARM START" position. Now, your brush cutter is under idle-speed states. 43CC PETROL BRUSH CUTTER TTL530GBC
- Page 1 and 2: 1 SAFETY AND OPERATING MANUAL Origi
- Page 3 and 4: SAFETY INSTRUCTIONS Warnings! Read
- Page 5 and 6: 11. Stop using the product while pe
- Page 7 and 8: 2. Stop the engine and unplug the s
- Page 9 and 10: Health Surveillance. All employees
- Page 11 and 12: Risk of fire / flammable materials
- Page 13 and 14: A 15 1 13 13a 19 14 20 18 17 22 3 2
- Page 15 and 16: A. Main unit 1. Engine 2. Upper sha
- Page 17 and 18: ACCESSORIES Torx screw driver (T25)
- Page 19 and 20: 2. Assembling shaft. 1). Align the
- Page 21: Ensure that there are no open flame
- Page 25 and 26: STOPPING ENGINE WARNING! The cuttin
- Page 27 and 28: Fig.24 TIPS 1. For best results, do
- Page 29 and 30: AIR FILTER 1. Inspect the air filte
- Page 31 and 32: Fig.29 4. To replace the spool simp
- Page 33 and 34: Troubleshooting Problem Possible ca
Fitting and adjusting the harness<br />
WARNING! Always attach the product to the harness. Do not carry it just<br />
by hand!<br />
1). Remove the harness from the loop, open the securing clip(37).<br />
2). Place the harness(38) so that is runs over the left shoulder, crossing the chest and back.<br />
The securing must be located at the right hip(Fig.12).<br />
3). Adjust the length of the harness so that the hook is approximately 15cm below your waist;<br />
locate the product to the harness by using the securing clip (36) that the angle of the cutting<br />
head is parallel to the surface being cut(Fig.13).<br />
Fig.12<br />
Fig.13<br />
4). In case of emergency, pull the rope of the quick release mechanism. The metal locking bar<br />
will be released from the harness(37) automatically by opening the securing clip(36) because<br />
of the weight of the machine, and the machine will drop away from you(Fig.14).<br />
37<br />
36<br />
12<br />
Fig.14