LAN/Network Tester KE7100 - Kurth Electronic GmbH
LAN/Network Tester KE7100 - Kurth Electronic GmbH
LAN/Network Tester KE7100 - Kurth Electronic GmbH
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
05/12 - Product design and specifications subject to change without notice. All trademarks belong to their respective companies.<br />
<strong>LAN</strong>/<strong>Network</strong> <strong>Tester</strong><br />
<strong>KE7100</strong><br />
KE7010<br />
Remote<br />
Fast and easy test of <strong>LAN</strong> Cabling for<br />
common faults:<br />
˜ Wire-mapping and precise fault location<br />
˜ Measures cable lengths up to 150 m (TDR)<br />
˜ Detects split pair from 6 feet on<br />
˜ Build-in user settable cable database<br />
˜ HUB-Blink for port identification<br />
˜ High power trace tone signal to use with<br />
optional PROBE310<br />
˜ Power over Ethernet Test (IEEE802.3af)<br />
˜ Identifies up to 32 individual Remote Units<br />
˜ Master and Remote over voltage protected<br />
up to 100V AC<br />
The <strong>KE7100</strong> <strong>LAN</strong>check is an easy-to-use and cost-saving tool for verification and troublehooting in small and big networks.<br />
The <strong>KE7100</strong> is the perfect device for network measurements without the need for documentation.<br />
Essential Copper Tests<br />
<strong>KE7100</strong> tests for wire continuity, opens, shorts, miswires and split pairs and shows test results on the easy-to-read graphical display<br />
with backlight. The length of the cable and distance to fault (short or open) is also shown by the <strong>KE7100</strong>.<br />
Cabel Trace<br />
Port identification via Link-Blink function and settabel trace tones for locating cables with capacitive Probe (optional PROBE310).<br />
Power over Ethernet (PoE)<br />
The <strong>KE7100</strong> can perform a Power over Ethernet Test (IEEE802.3af). <strong>KE7100</strong> not only checks for ability of Power over Ethernet, it<br />
detects the type available and what power level is supported. PoE is appearing more commonly as devices like wireless access points<br />
(WAP), IP cameras and IP telephones grow in popularity. Mismatches between equipment and power supply can cause a variety of<br />
problems.<br />
Setup<br />
The <strong>KE7100</strong> has 16 predefined wiring schemes further schemes are user settable via device. Cable types are also predefined and<br />
further types can be created by the user via device.<br />
®
05/12 - Product design and specifications subject to change without notice. All trademarks belong to their respective companies.<br />
Easy-to-use<br />
Detects external voltage<br />
Clear indication from wiring tests<br />
Detailed fault information<br />
PoE-Test: Measuring of voltage and current<br />
Specifications<br />
Ethernet <strong>LAN</strong> <strong>Tester</strong> <strong>KE7100</strong><br />
Wire Test Copper: Batteries:<br />
Check of wires connected to PIN and Pair 4 x 1,5 V Alkaline battery, operating time up<br />
Detects split pair from 6 ft (2 m) on<br />
16 dedicated wiring schemes predefined<br />
to 40 hours<br />
7 predefined cable types with VF, user defined Dimensions:<br />
cable types and wiring schemes possible 7.7" x 3.9"/3" x 1.8"<br />
Graphical display shows map with clear<br />
indication good / bad<br />
(95 x 100/78 x 45 mm)<br />
TDR measures all wires separately and shows Weight:<br />
distance to fault short / open 13.4 oz without battery (380 g)<br />
Power over Ethernet Test: Environment:<br />
Activation of PoE port, measuring of voltage Working temperature: 0 - +50°C<br />
and current. Shows available power in Watts Storage temperature: 25 - +75°C<br />
(IEEE802.3af) Humidity: 90 % non condensing<br />
Cable Trace:<br />
Hub-Link Blink function Trace tones to be<br />
detected by capacitive Probe (optional<br />
Active Remote Unit KE7010<br />
PROBE310) Housing:<br />
Solid and weather protected ABS with drop<br />
4 tones settable:<br />
protection<br />
1. SOLID: 1000 Hz<br />
2. ALT: 1000/800 Hz<br />
3. SOLID: 2600 Hz<br />
4. ALT: 2600/1900 Hz<br />
Features:<br />
ID programmable 01 - 32<br />
LED shows good / bad<br />
Over voltage protected up to 100 V AC<br />
Over voltage protection: Dimensions:<br />
Up to 100 V AC 2.4" x 1.6" x 1.0"<br />
(61 x 41 x 26 mm)<br />
Housing:<br />
Solid and weather protected ABS with drop Weight:<br />
protection<br />
1 oz (30 g)<br />
Ordering Information<br />
0.49410<br />
0.57613<br />
0.49415<br />
0.49416<br />
0.49417<br />
0.49451-7<br />
Your Dealer<br />
<strong>KE7100</strong> <strong>LAN</strong>/<strong>Network</strong> <strong>Tester</strong>, 1 Remote Unit KE7010, and<br />
with test cables<br />
Protective pouch for <strong>KE7100</strong> and Remote Units<br />
KE7010: 1 active Remote Unit, good / bad LED,<br />
programmable ID and test cables<br />
KE7010 KIT: 4 active Remote Units, good / bad LED,<br />
programmable ID and test cables<br />
KE7010 PRO KIT: 4 active Remote Units, good / bad LED,<br />
programmable ID, test cables and PROBE310 with pouch<br />
KE7107 <strong>Network</strong> and Cable Finder Kit in hard plastic case:<br />
<strong>KE7100</strong>, 1 Remote Unit KE7010, KE701 Telco, test cables<br />
and pouch<br />
KURTH ELECTRONIC <strong>GmbH</strong> • Im Scherbental 5 • D-72800 Eningen u.A. • GERMANY<br />
Tel. +49(0)7121-97 55-0 • Fax +49(0)7121-97 55 56<br />
www.kurthelectronic.de • e-mail: sales@kurthelectronic.de
Change language