Powerslide NEXT catalogue 2018. English.
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
7<br />
73.8<br />
102.7<br />
75.9<br />
MYFIT Recall liner lasting measurements<br />
84.8<br />
32.7<br />
304<br />
75.9<br />
311.76<br />
82.5<br />
133.6<br />
92.5<br />
POWERSLIDE <strong>NEXT</strong>- LASTING GUIDE<br />
105.7<br />
49.6<br />
82.5<br />
<strong>NEXT</strong> SHELL lasting measurements<br />
Measures in mm.<br />
#48/49 EU<br />
78.88<br />
84.18<br />
96.3<br />
68.8<br />
102.71<br />
105.92<br />
9<br />
76.2<br />
107<br />
318<br />
325<br />
139.3<br />
95.4<br />
78.4<br />
87.8<br />
33.9<br />
78.43<br />
85.13<br />
108.8<br />
51.1<br />
85.1<br />
MYFIT LINER HEAT MOLDING GUIDE<br />
BE READY TO ROLL<br />
LACE IT TIGHT IF YOU WANT MORE CONTROL.<br />
LACE IT MORE LOOSE IF YOU DESIRE MORE<br />
COMFORT.<br />
IF YOU WANT MORE SUPPORT MAKE SURE YOU<br />
LACE THE TOP AND HIGHER EYELETS UNDER<br />
YOUR CUFF.<br />
This will create less flex and more support.<br />
You can use also two separate laces, one lace<br />
for the bottom part and one lace for the top part.<br />
This way you can adjust both areas separately.<br />
CLOSE CUFF TIGHT OR MORE LOOSE?<br />
More loose for more forward flex, which then will<br />
train your stability and improve your ligaments and<br />
muscles. Close the cuff more tight if you want more<br />
support and performance and pushing harder. A tight<br />
closed cuff will normally put out more pressure on<br />
the shell and ankles.<br />
2<br />
3<br />
4<br />
HEAT MOLD YOUR LINER<br />
Pre-heat the oven at 80°-90°C, take the innersole out of the<br />
MYFIT liner. Put the liner in the centre of the oven.<br />
ATTENTION: make sure there is some distance between the<br />
liner and the oven walls and/or the heating source.<br />
Leave the MYFIT liners 5-7minutes inside the oven and then<br />
take them out.<br />
Put the innersole back into the MYFIT liners. Step into your<br />
skate and firmly close the boots as you usually do when you<br />
skate.<br />
Go into the optimal position: knees bend over the toe - and<br />
maintain this position until the liner has completely cooled<br />
down. We suggest you to sit down during this process, as it<br />
will take several minutes.<br />
THE RESULT: the perfect liner, that fits 100% to the anatomy<br />
of your foot.<br />
Make sure your boot or liner is heat moldable<br />
and follow the online instructions.*<br />
* How to heat mold your MYFIT liners -<br />
<strong>Powerslide</strong> Inline Skates Youtube Channel:<br />
https://youtu.be/WVe-rwbDCgE<br />
The heat molding process can be repeated as many<br />
times as desired.<br />
BEFORE YOU START SKATING:<br />
Check cuff screws or other screws like for 45º flap, etc.<br />
and tighten them if they started to get loose.<br />
Check the mounting screws and axles of your<br />
frame and tighten them in case they start to get<br />
loose.<br />
Check also your wheels and bearings if all can be<br />
taken off easily.<br />
100% performance<br />
100% fit<br />
100% comfort<br />
100% fun