ES721 ISO40 7 kW NL - HSD

More documents

Recommendations

Info

<strong>HSD</strong> 10.11 CHOICE OF TOOL The following requirements must be respected when choosing a tool: 1. Only use perfectly sharp tools. Make sure that they are locked firmly in the toolholder. 2. Never use bent, damaged, incomplete, or imperfectly balanced tools. 3. Always make sure that the surfaces of the tool are clean and undamaged before fitting it in the collet. Never operate tools beyond the rated speed punched on them or that specified by the manufacturer. 10.12 WHAT TO DO IF THE TOOL IS BLOCKED ON THE PIECE BEING WORKED In the models with an ISO type tool hooking, if the machine goes into emergency mode or stops with the tool blocked on the piece being worked, do not move the spindle along the Z axis! X Z If possible, release the piece manually and then carry out the tool changing manually. If this is not possible, proceed in the following way: 1. Supply air to the tool changing circuit 2. Slowly move the spindle away from the piece, moving it along the Z axis until the collet opens (“ON” output of sensor S2) 3. Check the collet spindle has been freed from the collet 4. Move the spindle completely away from the piece being worked 5. Remove the blocked tool manually. If these procedures are not observed, the tool holder will drag the locking system (collet/tie-rod) with it until the collet spindle is freed; owing to the force of the spring, the collet will then shoot back violently, perhaps breaking the tie-rod. 5801H0066 en Rev.01 32/48 Y
<strong>HSD</strong> 1 2 3 4 5 6 UTENSILE BLOCCATO UTENSILE RILASCIATO IMPATTO N. Description 1 ISO collet spindle 2 Spindle shaft 3 ISO collet (or bush) 4 Tie-rod The arrows show the direction in which the locking system moves after freeing the collet spindle Point in which the collet 5 knocks against the shaft 6 Breakage of the tie-rod 5801H0066 en Rev.01 33/48
Page 1 and 2: HSD MECHATRONIC D I V I S I O N HSD
Page 3 and 4: HSD 10.7.2 Electrospindle states an
Page 5 and 6: HSD § 4 TERMS OF WARRANTY HSD S.p.
Page 7 and 8: HSD 5.3 RISKS ASSOCIATED WITH THE E
Page 9 and 10: HSD § 6 TRANSPORT, PACKAGING, UNPA
Page 11 and 12: HSD § 7 TECHNICAL SPECIFICATIONS 7
Page 13 and 14: HSD § 8 DIMENSIONS AND MAIN PARTS
Page 15 and 16: HSD 8.1.2 Direct liquid coolant cou
Page 17 and 18: HSD 8.1.3 Deublin distributor, enco
Page 19 and 20: HSD § 9 INSTALLAZIONE HSD S.p.a. d
Page 21 and 22: HSD DPC 5801H0066 en Rev.01 21/48 !
Page 23 and 24: HSD 9.7 COMPRESSED AIR SPECIFICATIO
Page 25 and 26: HSD 9.10 AUTOMATIC CONE CLEANING 1.
Page 27 and 28: HSD § 10 OPERATION 10.1 GENERAL PR
Page 29 and 30: HSD 10.7.2 Electrospindle states an
Page 31: HSD 10.10 CHOICE OF TOOLHOLDER CONE
Page 35 and 36: HSD 11.1 DAILY MAINTENANCE 11.1.1 C
Page 37 and 38: HSD § 12 REPLACEMENT OF COMPONENTS
Page 39 and 40: HSD 12.1.2 Replacement and adjustme
Page 41 and 42: HSD 12.1.5 Sensor S5 adjustment Aft
Page 43 and 44: HSD § 14 LIST OF SPARE PARTS CODE
Page 45 and 46: HSD The tool holder is not locked:
Page 47 and 48: HSD § 16 DECLARATION OF INCORPORAT

ES721 ISO40 7 kW NL - HSD

Create successful ePaper yourself

Delete template?

Save as template?