OS-9 for the Prospector P1100 Board Guide

More documents

Recommendations

Info

GPIO Each sample contains an x, y coordinate as well as pressure information. The data is formatted into a six byte packet as defined in the table below. Each packet contains 10 bits of x, 10 bits of y, and 8 bits of pressure information. Table B-12 Touch Screen Descriptor Data Byte number Description 0 sync code - 0x80 1 header: bit 1: pendown bit 2: penup bit 3: penmove (may occur with pendown or penup) 2 bits 0..2: high 3 bits of x bits 3..6: high 4 bits of pressure bit 7: 0 3 bits 0..6: low 7 bits of x bit 7: 0 4 bits 0..2: high 3 bits of y bits 3..6: low 4 bits of pressure 5 bits 0..6: low bits of y bit 7: 0 This section of the driver has basic GPIO line control, where lines 0..9 are connected to a 7 segment display or LED. Each line can be controlled with an _os_write() call. (Refer to the UCBHEX program in the TEST directory.) 82 OS-9 for the Prospector P1100 Board Guide
MAUI Driver Descriptions Telecom This portion of the driver is not implemented. Supporting Modules Before this driver can be used, the following modules must be in memory: spf, sysmbuf, mbinstall. mbinstall must also be run before use. OS-9 for the Prospector P1100 Board Guide 83 B
Page 1 and 2:
www.radisys.com Revision A • July
Page 3 and 4:
Table of Contents Chapter 1: Instal
Page 5 and 6:
62 Descriptors for use with scllio
Page 7 and 8:
Chapter 1: Installing and Configuri
Page 9 and 10:
Installing and Configuring OS-9® R
Page 11 and 12:
Installing and Configuring OS-9® T
Page 13 and 14:
Installing and Configuring OS-9® C
Page 15 and 16:
Installing and Configuring OS-9® A
Page 17 and 18:
Installing and Configuring OS-9® S
Page 19 and 20:
Installing and Configuring OS-9® C
Page 21 and 22:
Page 23 and 24:
Installing and Configuring OS-9® I
Page 25 and 26:
Page 27 and 28:
Installing and Configuring OS-9® A
Page 29 and 30:
Chapter 2: Board-Specific Reference
Page 31 and 32: Board-Specific Reference Booting ov
Page 33 and 34: Board-Specific Reference The Fastbo
Page 35 and 36: Board-Specific Reference B_OKROM Th
Page 37 and 38: Board-Specific Reference This redef
Page 39 and 40: Board-Specific Reference Table 2-1
Page 45 and 46: Board-Specific Reference GPIO Usage
Page 49 and 50: Board-Specific Reference Syntax pfl
Page 51 and 52: Board-Specific Reference Syntax ucb
Page 53 and 54: Appendix A: Board-Specific Modules
Page 55 and 56: Board-Specific Modules Table A-1 Bo
Page 57 and 58: Board-Specific Modules Table A-2 Ge
Page 59 and 60: Board-Specific Modules System Confi
Page 61 and 62: Board-Specific Modules RAM Disk Sup
Page 63 and 64: Board-Specific Modules Network Conf
Page 65 and 66: Appendix B: MAUI Driver Description
Page 67 and 68: MAUI Driver Descriptions GX_SA1100
Page 69 and 70: MAUI Driver Descriptions Table B-1
Page 71 and 72: MAUI Driver Descriptions This drive
Page 73 and 74: MAUI Driver Descriptions Build the
Page 79 and 80: MAUI Driver Descriptions Encoding a
Page 81: MAUI Driver Descriptions UCB Audio
Page 85 and 86: MAUI Driver Descriptions Raw Mode A
Page 87 and 88: MAUI Driver Descriptions 3. touch_c
show all

OS-9 for the Prospector P1100 Board Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?