OS-9 for the Prospector P1100 Board Guide

More documents

Recommendations

Info

Boot Options Following are the default boot options for the reference board. You can select these by hitting the space bar when the Now Trying to Override Autobooters message appears on the console port when booting. You can configure these booters by altering the default.des file at the following location: MWOS/OS9000/ARMV4/PORTS/PROSPECTOR/ROM Booters can be configured to be either menu or auto booters. The auto booters automatically try and boot in order from each entry in the auto booter array. Menu booters from the defined menu booter array are chosen interactively from the console command line after getting the boot menu. Booting from Flash When the romcnfg.h has a ROM search list defined, the options ro and lr appear in the boot menu. If no search list is defined, N/A appears in the boot menu. If an OS-9 ROM Image is programmed into Flash, the system can boot and run from Flash. ro ROM boot—the system runs from the Flash bank. lr load to RAM—the system copies the ROM Image from Flash into RAM and runs from there. 30 OS-9 for the Prospector P1100 Board Guide
Board-Specific Reference Booting over Serial Communications Port via kermit The system can down-load a ROM Image in binary form over its serial communication port at 57600 using the kermit protocol. The speed of this transfer depends of the size of the image. If the transfer is successful, a dot is shown for every block of data processed. The communications port is clearly marked and located on the side of the development board. ker Kermit boot—The ROM image is sent via the kermit protocol into system RAM and runs from there. Restart Booter The restart booter allows a way to restart the bootstrap sequence. q Quit—quit and attempt to restart the booting process. Break Booter The break booter allows entry to the system level debugger (if one exists). If the debugger is not in the system the system will reset. break Break—break and enter the system level debugger rombug. OS-9 for the Prospector P1100 Board Guide 31 2
Page 1 and 2: www.radisys.com Revision A • July
Page 3 and 4: Table of Contents Chapter 1: Instal
Page 5 and 6: 62 Descriptors for use with scllio
Page 7 and 8: Chapter 1: Installing and Configuri
Page 9 and 10: Installing and Configuring OS-9® R
Page 11 and 12: Installing and Configuring OS-9® T
Page 13 and 14: Installing and Configuring OS-9® C
Page 15 and 16: Installing and Configuring OS-9® A
Page 17 and 18: Installing and Configuring OS-9® S
Page 19 and 20: Installing and Configuring OS-9® C
Page 23 and 24: Installing and Configuring OS-9® I
Page 27 and 28: Installing and Configuring OS-9® A
Page 29: Chapter 2: Board-Specific Reference
Page 33 and 34: Board-Specific Reference The Fastbo
Page 35 and 36: Board-Specific Reference B_OKROM Th
Page 37 and 38: Board-Specific Reference This redef
Page 39 and 40: Board-Specific Reference Table 2-1
Page 45 and 46: Board-Specific Reference GPIO Usage
Page 49 and 50: Board-Specific Reference Syntax pfl
Page 51 and 52: Board-Specific Reference Syntax ucb
Page 53 and 54: Appendix A: Board-Specific Modules
Page 55 and 56: Board-Specific Modules Table A-1 Bo
Page 57 and 58: Board-Specific Modules Table A-2 Ge
Page 59 and 60: Board-Specific Modules System Confi
Page 61 and 62: Board-Specific Modules RAM Disk Sup
Page 63 and 64: Board-Specific Modules Network Conf
Page 65 and 66: Appendix B: MAUI Driver Description
Page 67 and 68: MAUI Driver Descriptions GX_SA1100
Page 69 and 70: MAUI Driver Descriptions Table B-1
Page 71 and 72: MAUI Driver Descriptions This drive
Page 73 and 74: MAUI Driver Descriptions Build the
Page 79 and 80: MAUI Driver Descriptions Encoding a
Page 81 and 82:
MAUI Driver Descriptions UCB Audio
Page 83 and 84:
MAUI Driver Descriptions Telecom Th
Page 85 and 86:
MAUI Driver Descriptions Raw Mode A
Page 87 and 88:
MAUI Driver Descriptions 3. touch_c
show all

OS-9 for the Prospector P1100 Board Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?