Understanding Heat Exchanger Reading 03- Part 2 of 2 The ARAMCO Std.

More documents

Recommendations

Info

Document Responsibility: Heat Transfer Equipment Standards Committee 32-SAMSS-007 Draft Date: 1 December 2013 Next Planned Update: 1 December 2018 Manufacture of Shell and Tube Heat Exchangers ii. For attachments with a reinforcing plate, similar examination as in (i) above shall be performed at the nozzle. 100% MT or 100% LP shall be also performed on the final surface of the fillet welds attaching the reinforcing pad to exchanger and nozzle. (5) Inspection requirements for connections attached to nozzles and manways per paragraph 8.5.2 shall be according to note 4 of this table. (6) 100% MT or 100% LP shall be applied to the root pass and final surface of lap-welded Category - C weld joint. Page 49 of 49
Part 3: Inspection & Testing Requirements Saudi Aramco Form-175 CODE NUMBER: IR323100 SCOPE: HEAT EXCHANGERS: Shell and Tubes. TEST AND INSPECTION PER: 32-SAMSS-007and Specifications As Noted Below. Charlie Chong/ Fion Zhang
Page 1 and 2:
My Reading on Heat Exchanger Readin
Page 3:
Charlie Chong/ Fion Zhang Fion Zhan
Page 7:
The Magical Book of Heat Exchanger
Page 11:
Charlie Chong/ Fion Zhang 有书
Page 15:
Charlie Chong/ Fion Zhang American
Page 19:
Contents 1. Scope 2. Normative refe
Page 23:
8.1.2 Castings shall not be used un
Page 27:
8.3 Tubes 8.3.1 Integrally finned t
Page 31:
Tubes All welded tubes shall be edd
Page 35:
Tubes- All welded tubes shall be ed
Page 39:
Tubes- All welded tubes shall be ed
Page 43:
Kettle-type Heat Exchangers Charlie
Page 47:
9.1.2 For removable-bundle heat exc
Page 51:
TEMA (8th edition), TABLE RCB-4.3 S
Page 55:
Tubes All tubes including U-tubes s
Page 59:
• 9.5.6 Tubes shall be welded to
Page 63:
9.6.3 The heat-treated portion of t
Page 67:
Post-weld Heat Treatment of fabrica
Page 71:
Heating Cycle ASME A335 Cr-Mo P92 S
Page 75:
9. 7 Dimensional tolerances 9.7.1 M
Page 79:
Piping Fabrication Dimensional tole
Page 83:
Ra value The roughness of a surface
Page 87:
Elcometer 7062 MarSurf PS10 Surface
Page 91:
9.8.4 The flatness tolerance on pas
Page 95:
9.10 Tube-to-tubesheet joints 9.10.
Page 99:
Tube Expander Charlie Chong/ Fion Z
Page 103:
Tube Expansion 1. If welded-and-exp
Page 107:
Dinner Time 20180601- 1817hrs 儿
Page 111:
Quality assurance verification that
Page 115:
Quality assurance verification that
Page 119:
Quality assurance review and/or exa
Page 123:
10.1.2 No tubes or tube holes shall
Page 127 and 128:
Charlie Chong/ Fion Zhang
Page 130:
10.2.3 For non-magnetic materials,
Page 134:
Table 5-Hardness limits Material Ma
Page 138:
Brinell hardness Hardness shall be
Page 142:
Brinell Hardness Testing Charlie Ch
Page 146:
Overlay weldments shall be liquid-p
Page 150:
Page 154:
Page 158 and 159:
Picasso Charlie Chong/ Fion Zhang
Page 160:
1 0.3 Pressure testing 10.3.1 In th
Page 164:
Pressure Testing Welded-and-expande
Page 168:
Pressure Testing The minimum fluid
Page 172:
Pressure Testing The water used for
Page 176:
Pressure Testing The water used for
Page 180:
Pressure Testing Charlie Chong/ Fio
Page 184:
Pressure Testing Chart- Recorder Ch
Page 188:
Re-Hydrotesting Flanged joints that
Page 192:
Re-Hydrotesting Flanged joints that
Page 196:
Break 擂茶配料编辑擂
Page 200:
11.1.5 All threaded connections sha
Page 204:
12 Supplemental requirements 12.1 G
Page 208:
12.2 Design 12.2.1 The attachment o
Page 212:
Set-On Connection Examination for l
Page 216:
12.3 Examination 12.3.1 All materia
Page 220:
Plate Ultrasonic Testing (Pre-forme
Page 224:
Plate Ultrasonic Testing (Pre-forme
Page 228:
Ultrasonic Examination of Forging A
Page 232:
Page 236:
Page 240:
Hot Forging Charlie Chong/ Fion Zha
Page 244:
Hot Forging Head Charlie Chong/ Fio
Page 248:
Cold Forming Charlie Chong/ Fion Zh
Page 252:
Cold Forming https://www.youtube.co
Page 256:
12.3.3 For ultrasonic examination o
Page 260:
MPI Magnetic-particle examination s
Page 264:
12.3.9 On components subject to ful
Page 268:
MPI- Magnetic Particle Testing Char
Page 272:
12.3.10 A full radiographic examina
Page 276:
Annex A (informative) Recommended p
Page 280:
U-Bend Thinning For U-tube type bun
Page 284:
Twisted Tube Design Charlie Chong/
Page 288:
A.2.4 Tube bundle skid bars- Guidan
Page 292:
A.3 Fabrication A.3.1 Shell - Guida
Page 296:
Annex B (informative) Shell-and-tub
Page 299 and 300:
API Standard 660 / ISO 16812:2002 (
Page 302 and 303:
ISO 16812:2002(E) API Standard 660
Page 304 and 305:
Page 306 and 307:
Page 309 and 310: ISO 16812:2002(E) API Standard 660
Page 312 and 313: Materials System Specification 32-S
Page 314 and 315: Document Responsibility: Heat Trans
Page 363 and 364: INSPECTION & TESTING REQUIREMENTS S
Page 365 and 366: INSPECTION & TESTING REQUIREMENTS S
Page 368: Charlie Chong/ Fion Fion Zhang Zhan
show all

Understanding Heat Exchanger Reading 03- Part 2 of 2 The ARAMCO Std.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?