Understanding Heat Exchanger Reading 03- Part 2 of 2 The ARAMCO Std.

More documents

Recommendations

Info

Tubes All welded tubes shall be eddy-current tested in the finished condition over their full length. Charlie Chong/ Fion Zhang http://www.pardtube.com/technicals/non-destructive-tests-for-welded-tube/
Page 1 and 2: My Reading on Heat Exchanger Readin
Page 3: Charlie Chong/ Fion Zhang Fion Zhan
Page 7: The Magical Book of Heat Exchanger
Page 11: Charlie Chong/ Fion Zhang 有书
Page 15: Charlie Chong/ Fion Zhang American
Page 19: Contents 1. Scope 2. Normative refe
Page 23: 8.1.2 Castings shall not be used un
Page 27: 8.3 Tubes 8.3.1 Integrally finned t
Page 33: Tubes All welded tubes shall be edd
Page 37: Tubes- All welded tubes shall be ed
Page 41: 9 Fabrication 9.1 Shells 9.1.1 All
Page 45: Kettle-type Heat Exchangers Charlie
Page 49: Transverse baffle-to-shell baffle-t
Page 53: 9.2 Pass-partition plates Pass-part
Page 57: 9.5 Welding 9.5.1 Welds may be made
Page 61: 9.6 Heat treatment 9.6.1 Machined c
Page 65: 9.6.4 Post-weld heat treatment of f
Page 69: • 9.6.5 The purchaser shall speci
Page 73: Post-weld Heat Treatment - on site
Page 77: Gap: 3 mm max Dimensional tolerance
Page 81:
9.8 Gasket contact surfaces other t
Page 85:
Roughness Parameters (EN ISO 4287)
Page 89:
9.8.2 The flatness tolerance (maxim
Page 93:
9.9 Tube holes 9.9.1 Tube-hole groo
Page 97:
Experimental Investigation of Frict
Page 101:
9.10.2 If welded-and-expanded joint
Page 105:
9.11 Assembly 9.11.1 Match marks or
Page 109:
10 Inspection and testing 10.1 Qual
Page 113:
Quality assurance witnessing of hyd
Page 117:
Quality assurance verification that
Page 121:
Quality assurance review and/or exa
Page 125:
10.2 Quality control 10.2.1 Radiogr
Page 128:
UW-11 RADIOGRAPHIC AND ULTRASONIC E
Page 132:
10.2.5 Weld-hardness testing shall
Page 136:
Table 5-Hardness limits Material Ma
Page 140:
Brinell Hardness Testing Charlie Ch
Page 144:
10.2.6 At welded joints in alloy-cl
Page 148:
Overlay weldments shall be liquid-p
Page 152:
Overlay weldments shall be liquid-p
Page 156:
Picasso Charlie Chong/ Fion Zhang
Page 159 and 160:
Picasso Charlie Chong/ Fion Zhang
Page 162:
Pressure testing Welded-and-expande
Page 166:
Pressure Testing Welded-and-expande
Page 170:
Pressure Testing The water used for
Page 174:
Pressure Testing The water used for
Page 178:
Pressure Testing The chloride conte
Page 182:
Pressure testing Charlie Chong/ Fio
Page 186:
• 10.3.5 Any additional requireme
Page 190:
Re-Hydrotesting Flanged joints that
Page 194:
10.4 Nameplates and stampings 1 0.4
Page 198:
11 Preparation for shipment 11.1 Pr
Page 202:
11.2 Identification 11.2.1 The item
Page 206:
Thick Walled Shell Construction Cha
Page 210:
Design…. Set-on type connections
Page 214:
Plate Sub-Surface Defects Charlie C
Page 218:
Examination 12.3.1 All material for
Page 222:
Plate Ultrasonic Testing (Pre-forme
Page 226:
Plate Ultrasonic Testing (Pre-forme
Page 230:
Ultrasonic Examination of Forging A
Page 234:
Ultrasonic Examination of Forging A
Page 238:
Hot Forging Charlie Chong/ Fion Zha
Page 242:
Hot Forging Charlie Chong/ Fion Zha
Page 246:
Cold Forming Charlie Chong/ Fion Zh
Page 250:
Hot Forming https://www.youtube.com
Page 254:
Cold Forming Charlie Chong/ Fion Zh
Page 258:
MPI Magnetic-particle examination s
Page 262:
12.3.5 Magnetic-particle examinatio
Page 266:
MPI- Magnetic Particle Testing Char
Page 270:
Tabulated Part Description NDT Cove
Page 274:
Part Description NDT Coverage Claus
Page 278:
A.2.2 Tube bundle and tubes- Guidan
Page 282:
Helical Baffles Charlie Chong/ Fion
Page 286:
Twisted Tube Design Charlie Chong/
Page 290:
A.2.5 Tube to tubesheet joint- Guid
Page 294:
A.4 Preparation for shipment protec
Page 298 and 299:
ISO 16812:2002(E) API Standard 660
Page 300:
Annex C (informative) Shell-and-tub
Page 303 and 304:
API Standard 660 / ISO 16812:2002 (
Page 305 and 306:
API Standard 660 / ISO 16812:2002 (
Page 307:
Annex D (informative) Responsibilit
Page 310:
Part 2: Materials System Specificat
Page 313 and 314:
Document Responsibility: Heat Trans
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361:
Part 3: Inspection & Testing Requir
Page 364 and 365:
INSPECTION & TESTING REQUIREMENTS S
Page 366:
Charlie Chong/ Fion Zhang
show all

Understanding Heat Exchanger Reading 03- Part 2 of 2 The ARAMCO Std.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?