TITAN TTL632CHN PETROL CHAINSAW 3147H
Titan 35cc Chainsaw Titan 35cc Chainsaw
GB IE Operation Starting / Stopping TTL632CHN by TITAN In more detail... Getting started... 23 1. 4. 5. 2 2 4. 13 5. 13 Fig. 27 4 27 6 2. 3. NOTE: If the engine does not start, the engine may be flooded. Flooding is caused by too much fuel mixture applied at the wrong time and can prevent a product from starting. Follow below procedure: Set the ignition switch (23) to position “STOP” STOP . Push the choke lever (4) fully back to OPEN position . Remove the spark plug (22) and dry it. Pull the recoil starter handle (27) several times to drain the fuel from the combustion chamber. Wait until fuel evaporates and refit the spark plug. Clean up any spilled fuel and move the product at least 3 metres (10’) away before starting the engine to avoid any accidental fire. Wait for the engine to cool down and then start the product as described in section “Cold start”. 14 Stopping > > Release the throttle interlock (2) / throttle trigger (13) and let the product run at its idle speed for 10 – 15 seconds. > > Set the ignition switch (23) to position “STOP” STOP (Fig. 28). 42 MNL_TTL632CHN_TIT_GB_V02_150527.indd 42 5/27/15 1:55 PM
TTL632CHN by TITAN Operation GB IE 23 5. 13 5. 2 Fig. 28 WARNING! The saw chain will continue to run for a short time even after the engine has been switched off! Wait until the saw chain has come to a complete stop before placing the product on the ground! NOTE: The product will become very warm after a long period of use; allow it to cool down completely before restart. If the product cannot be switched on with warm start procedure, then refer to the cold start procedure. Basic operating / cutting procedure Chainsaws by their very nature are Extremely Dangerous machines and should be handled with respect. We STRONGLY recommend that before use of this product you attend a Chainsaw Training Course to familiarise yourself with the maintenance and usage of these products. Please thoroughly read this manual and adhere to all safety instructions at all times. Titan Powers Tool (UK) Ltd will not be held liable for any accidents/injuries caused due to misuse or incorrect maintenance of this product. 1. In more detail... Getting started... > > To become proficient attend a recognised chain saw training course to learn how to operate chain saws safely and effectively. Familiarise yourself with all the controls and switches. Practise all movements with the product switched off. > > Always hold the product firmly with both hands. Front handle (6) with the left hand and rear handle (1) with the right hand. Fully grip both handles at all times during operation. Never operate the product using only one hand. > > Only use the product with a secure stance. Hold the product at the right-hand side of your body (Fig. 29). > > Check the proper lubrication as described in section “Chain and guide bar - Chain lubrication” before performing any cut. 43 MNL_TTL632CHN_TIT_GB_V02_150527.indd 43 5/27/15 1:55 PM
- Page 1 and 2: Petrol Chainsaw 35cc Original Instr
- Page 3 and 4: GB IE Let’s get started... These
- Page 5 and 6: TTL632CHN by TITAN Safety informati
- Page 7 and 8: TTL632CHN by TITAN Safety informati
- Page 9 and 10: TTL632CHN by TITAN Safety informati
- Page 11 and 12: TTL632CHN by TITAN Safety informati
- Page 13 and 14: TTL632CHN by TITAN Safety informati
- Page 15 and 16: TTL632CHN by TITAN Safety informati
- Page 17 and 18: TTL632CHN by TITAN Safety informati
- Page 19 and 20: TTL632CHN by TITAN Safety informati
- Page 21 and 22: TTL632CHN by TITAN Your product GB
- Page 23 and 24: TTL632CHN by TITAN Your product / B
- Page 25 and 26: TTL632CHN by TITAN Before you start
- Page 27 and 28: TTL632CHN by TITAN Before you start
- Page 29 and 30: TTL632CHN by TITAN Before you start
- Page 31 and 32: TTL632CHN by TITAN Before you start
- Page 33 and 34: TTL632CHN by TITAN Quick start GB I
- Page 35 and 36: TTL632CHN by TITAN Stopping Quick s
- Page 37 and 38: TTL632CHN by TITAN Intended use Pro
- Page 39 and 40: TTL632CHN by TITAN Chain speed Prod
- Page 41: TTL632CHN by TITAN Operation GB IE
- Page 45 and 46: TTL632CHN by TITAN Kickback Operati
- Page 47 and 48: TTL632CHN by TITAN Operation GB IE
- Page 49 and 50: TTL632CHN by TITAN Operation GB IE
- Page 51 and 52: TTL632CHN by TITAN Care and mainten
- Page 53 and 54: TTL632CHN by TITAN Care and mainten
- Page 55 and 56: TTL632CHN by TITAN Care and mainten
- Page 57 and 58: TTL632CHN by TITAN Fuel tank Care a
- Page 59 and 60: TTL632CHN by TITAN Troubleshooting
- Page 61 and 62: TTL632CHN by TITAN Troubleshooting
- Page 63: GB-IE Titan Power Tools (UK) Ltd Tr
GB<br />
IE<br />
Operation<br />
Starting / Stopping<br />
<strong>TTL632CHN</strong> by <strong>TITAN</strong><br />
In more detail... Getting started...<br />
23<br />
1.<br />
4.<br />
5.<br />
2 2<br />
4. 13 5. 13<br />
Fig. 27<br />
4 27 6<br />
2. 3.<br />
NOTE: If the engine does not start, the engine may be flooded.<br />
Flooding is caused by too much fuel mixture applied at the wrong time<br />
and can prevent a product from starting. Follow below procedure:<br />
Set the ignition switch (23) to position “STOP” STOP . Push the choke<br />
lever (4) fully back to OPEN position . Remove the spark plug<br />
(22) and dry it. Pull the recoil starter handle (27) several times to drain<br />
the fuel from the combustion chamber.<br />
Wait until fuel evaporates and refit the spark plug. Clean up any spilled<br />
fuel and move the product at least 3 metres (10’) away before starting<br />
the engine to avoid any accidental fire. Wait for the engine to cool<br />
down and then start the product as described in section “Cold start”.<br />
14<br />
Stopping<br />
> > Release the throttle interlock (2) / throttle trigger (13) and let the product run at<br />
its idle speed for 10 – 15 seconds.<br />
> > Set the ignition switch (23) to position “STOP” STOP (Fig. 28).<br />
42<br />
MNL_<strong>TTL632CHN</strong>_TIT_GB_V02_150527.indd 42<br />
5/27/15 1:55 PM