BAKER HUGHES - Drilling Fluids Reference Manual
Oil / Synthetic Fluids Table 5-36 Products required to build 100 bbl of SYN-TEQ Fluid: 85/15 Synthetic/Water Ratio (SWR) Maximum Temperature °F (°C) Products 250 (121) 300 (149) 350 (177) 400 (204) 450 (232) OMNI-TEC TM , gal OMNI-MUL TM , gal OMNI-TROL TM , 50 lb sacks MIL-LIME TM , 50 lb sacks 100 25 10 8 115 50 20 9 140 62.5 20 11 160 75 30 13 180 112 30 16 85/15 SWR ISO-TEQ, Brine*, CARBO-GEL, (bbl) (bbl) (50 lb sacks) 8.0 82 15 9 18 8.5 80 14 9 50 9.0 79 14 9 76 9.5 77 14 9 103 10.0 76 14 9 129 10.5 74 13 9 156 11.0 72 13 9 182 11.5 71 13 9 209 12.0 69 13 9 236 12.5 68 12 8 262 13.0 66 12 8 289 13.5 65 12 8 316 14.0 63 12 8 342 14.5 62 11 8 369 15.0 60 11 7 395 15.5 59 11 7 422 16.0 57 10 7 449 16.5 56 10 7 475 17.0 54 10 7 502 17.5 52 10 7 528 18.0 51 9 5 555 18.5 49 9 5 582 19.0 48 9 5 608 Fluid Weight, (lb m /gal) *Saturated NaCl or 250,000 CaCl 2 water. MIL-BAR, (100 lb sacks) The volumes and densities are accurate to ±1%. Because it is not possible for a able to show formulations with numerous internal phase salinities and temperature stabilities, it is recommended that a material balance approach be utilized prior to the formulation of large quantities of CARBO-DRILL. Baker Hughes Drilling Fluids Reference Manual 5-60 Revised 2006
Baker Hughes Drilling Fluids Table 5-37 Products Required to build 100 bbl of SYN-TEQ SM Fluid: 90/10 and 95/5 Synthetic/Water Ratios (SWR) Maximum Temperature °F (°C) Products 250 (121) 300 (149) 350 (177) 400 (204) 450 (232) OMNI-TEC TM , gal OMNI-MUL TM , gal OMNI-TROL TM , 50 lb sacks MIL-LIME TM , 50 lb sacks 85 25 10 5 100 50 20 6 125 62.5 20 7 140 100 30 12 170 125 30 14 Fluid Weight, (lb m /gal) ISO-TEQ, (bbl) 90/10 SWR Brine*, (bbl) CARBO-GEL, (50 lb sacks) MIL-BAR, (100 lb sacks) 7.6 88 10 10 0 8.0 86 10 10 22 8.5 85 10 10 49 9.0 83 10 10 75 9.5 82 9 10 102 10.0 80 9 10 129 10.5 78 9 10 156 11.0 77 9 10 183 11.5 75 8 10 210 12.0 73 8 10 236 12.5 72 8 10 263 13.0 70 8 10 290 13.5 69 8 10 317 14.0 67 8 10 343 14.5 65 8 10 370 15.0 63 7 10 397 95/5 OWR 16.0 62 3 8 471 16.5 61 3 8 499 17..0 59 3 8 526 17.5 57 3 8 553 18.0 56 3 7 579 18.5 54 3 5 606 19.0 52 3 4 633 19.5 50 3 3 660 20.0 49 3 2 687 *Saturated NaCl or 250,000 CaCl 2 water. The volumes and densities are accurate to ±1%. Because it is not possible for a able to show formulations with numerous internal phase salinities and temperature stabilities, it is recommended that a material balance approach be utilized prior to the formulation of large quantities of CARBO-DRILL. Baker Hughes Drilling Fluids Reference Manual Revised 2006 5-61
- Page 220 and 221: Oil / Synthetic Fluids Ions surroun
- Page 222 and 223: Oil / Synthetic Fluids Surface ener
- Page 224 and 225: Oil / Synthetic Fluids to form oil
- Page 226 and 227: Oil / Synthetic Fluids As indicated
- Page 228 and 229: Oil / Synthetic Fluids Oil Density
- Page 230 and 231: Oil / Synthetic Fluids As the conce
- Page 232 and 233: Oil / Synthetic Fluids lower pH. Th
- Page 234 and 235: Oil / Synthetic Fluids One of the m
- Page 236 and 237: Oil / Synthetic Fluids Amine Lignit
- Page 238 and 239: Oil / Synthetic Fluids The MAGMA-TE
- Page 240 and 241: Oil / Synthetic Fluids System Maint
- Page 242 and 243: Oil / Synthetic Fluids CARBO-MUL ®
- Page 244 and 245: Oil / Synthetic Fluids CARBO-TEC ®
- Page 246 and 247: Oil / Synthetic Fluids CARBO-VIS C
- Page 248 and 249: Oil / Synthetic Fluids MAGMA-TROL
- Page 250 and 251: Oil / Synthetic Fluids OMNI-MUL ®
- Page 252 and 253: Oil / Synthetic Fluids OMNI-TROL /
- Page 254 and 255: Oil / Synthetic Fluids 8. Do not us
- Page 256 and 257: Oil / Synthetic Fluids Solids contr
- Page 258 and 259: Oil / Synthetic Fluids Figure 5-22
- Page 260 and 261: Oil / Synthetic Fluids Salts Since
- Page 262 and 263: Oil / Synthetic Fluids Table 5-28 C
- Page 264 and 265: Oil / Synthetic Fluids Table 5-30 C
- Page 266 and 267: Oil / Synthetic Fluids Table 5-32 C
- Page 268 and 269: Oil / Synthetic Fluids Table 5-34 F
- Page 272 and 273: Oil / Synthetic Fluids Table 5-38 F
- Page 274 and 275: Oil / Synthetic Fluids Metric Conve
- Page 276 and 277: Oil / Synthetic Fluids Metric Conve
- Page 278 and 279: Oil / Synthetic Fluids • Metric C
- Page 280 and 281: Reservoir Application Fluids Chapte
- Page 282 and 283: TABLE OF CONTENTS System Benefits..
- Page 284 and 285: TABLE OF CONTENTS TABLE 6 - 19 PREP
- Page 286 and 287: RESERVOIR APPLICATION FLUIDS In pet
- Page 288 and 289: RESERVOIR APPLICATION FLUIDS Figure
- Page 290 and 291: RESERVOIR APPLICATION FLUIDS Clays
- Page 292 and 293: RESERVOIR APPLICATION FLUIDS Conden
- Page 294 and 295: RESERVOIR APPLICATION FLUIDS The Sh
- Page 296 and 297: RESERVOIR APPLICATION FLUIDS Figure
- Page 298 and 299: RESERVOIR APPLICATION FLUIDS Struct
- Page 300 and 301: RESERVOIR APPLICATION FLUIDS contai
- Page 302 and 303: RESERVOIR APPLICATION FLUIDS throat
- Page 304 and 305: RESERVOIR APPLICATION FLUIDS soluti
- Page 306 and 307: RESERVOIR APPLICATION FLUIDS tested
- Page 308 and 309: RESERVOIR APPLICATION FLUIDS • 0.
- Page 310 and 311: RESERVOIR APPLICATION FLUIDS Under-
- Page 312 and 313: RESERVOIR APPLICATION FLUIDS Typica
- Page 314 and 315: RESERVOIR APPLICATION FLUIDS Compar
- Page 316 and 317: RESERVOIR APPLICATION FLUIDS CLEAR-
- Page 318 and 319: RESERVOIR APPLICATION FLUIDS 1.20 S
Baker Hughes <strong>Drilling</strong> <strong>Fluids</strong><br />
Table 5-37 Products Required to build 100 bbl of SYN-TEQ SM Fluid: 90/10 and 95/5<br />
Synthetic/Water Ratios (SWR)<br />
Maximum Temperature °F (°C)<br />
Products 250 (121) 300 (149) 350 (177) 400 (204) 450 (232)<br />
OMNI-TEC TM , gal<br />
OMNI-MUL TM , gal<br />
OMNI-TROL TM , 50 lb sacks<br />
MIL-LIME TM , 50 lb sacks<br />
85<br />
25<br />
10<br />
5<br />
100<br />
50<br />
20<br />
6<br />
125<br />
62.5<br />
20<br />
7<br />
140<br />
100<br />
30<br />
12<br />
170<br />
125<br />
30<br />
14<br />
Fluid Weight,<br />
(lb m /gal)<br />
ISO-TEQ,<br />
(bbl)<br />
90/10 SWR<br />
Brine*,<br />
(bbl)<br />
CARBO-GEL,<br />
(50 lb sacks)<br />
MIL-BAR,<br />
(100 lb sacks)<br />
7.6 88 10 10 0<br />
8.0 86 10 10 22<br />
8.5 85 10 10 49<br />
9.0 83 10 10 75<br />
9.5 82 9 10 102<br />
10.0 80 9 10 129<br />
10.5 78 9 10 156<br />
11.0 77 9 10 183<br />
11.5 75 8 10 210<br />
12.0 73 8 10 236<br />
12.5 72 8 10 263<br />
13.0 70 8 10 290<br />
13.5 69 8 10 317<br />
14.0 67 8 10 343<br />
14.5 65 8 10 370<br />
15.0 63 7 10 397<br />
95/5 OWR<br />
16.0 62 3 8 471<br />
16.5 61 3 8 499<br />
17..0 59 3 8 526<br />
17.5 57 3 8 553<br />
18.0 56 3 7 579<br />
18.5 54 3 5 606<br />
19.0 52 3 4 633<br />
19.5 50 3 3 660<br />
20.0 49 3 2 687<br />
*Saturated NaCl or 250,000 CaCl 2 water.<br />
The volumes and densities are accurate to ±1%. Because it is not possible for a able to show formulations with numerous<br />
internal phase salinities and temperature stabilities, it is recommended that a material balance approach be utilized prior to<br />
the formulation of large quantities of CARBO-DRILL.<br />
Baker Hughes <strong>Drilling</strong> <strong>Fluids</strong><br />
<strong>Reference</strong> <strong>Manual</strong><br />
Revised 2006 5-61