FAIRMONT HOTELS & RESORTS -DESIGN STANDARDS

More documents

Recommendations

Info

Fairmont Hotels & Resorts · Design Standards APPENDICES Hardware Designation (continued) derived from the following standards. Provide products complying with these standards and requirements specified elsewhere in this Section. a) Butts and Hinges: ANSI/BHMA A156.1 b) Bored and Pre-assembled Locks and Latches: ANSI/BHMA A156.2 c) Exit Devices: ANSI/BHMA A156.3 d) Door Controls – Closers: ANSI/BHMA A156.4 e) Auxiliary Locks and Associated Products: ANSI/BHMA A156.5 f) Architectural Door Trim: ANSI/BHMA A156.6 g) Template Hinge Dimensions: ANSI/BHMA A156.7 h) Door Controls – Overhead Holders: ANSI/BHMA A156.8 i) Interconnected Locks and Latches: ANSI/BHMA A156.12 j) Mortise Locks and Latches: ANSI/BHMA A156.13 k) Sliding and Folding Door Hardware: ANSI/BHMA A156.14 l) Closer Holder Release Devises: ANSI/BHMA A156.15 m) Auxiliary Hardware: ANSI/BHMA A156.16 n) Self-Closing Hinges and Pivots: ANSI/BHMA A156.17 o) Materials and Finishes: ANSI/BHMA A156.18. 1.6. Materials and Fabrication A. Do not use manufacturers’ products that have manufacturer’s name or trade name displayed in a visible location (omit removable name plates) except in conjunction with required fire-rated labels. B. Produce hardware units of basic metal and forming method indicated using manufacturer’s standard metal alloy, composition, temper, and hardness, but in no case of lesser (commercially recognized) quality than specified for applicable hardware units for finish designations indicated. C. Do not provide hardware that has been prepared for self-tapping sheet metal screws, except as specifically indicated. D. Finish exposed (exposed under any condition) screws to match hardware finish or, if exposed in surfaces of other work, to match finish of this other work as closely as possible “prepared for paint” surfaces to receive painted finish. 1.7. Hinges, Butts, and Pivots A. Templates: Except for hinges and pivots to be installed entirely (both leaves) into wood doors and frames, provide only template-produced units. REV. MARCH 2006 248 © 2002, Fairmont Hotels and Resorts. All Rights Reserved.
Fairmont Hotels & Resorts · Design Standards APPENDICES Hinges, Butts, and Pivots (continued) B. Screws: Provide Phillip flat-head screws complying with the following requirements: 1. The metal doors and frames install machine screws into drilled and tapped holes. 2. The wood doors and frames install wood screws. 3. For fire-rated wood doors install #12 x 1-1/4”, threaded-to-the-head steel wood screws. 4. Finish screw heads to match surface of hinges or pivots. C. Hinge Pins: Except as otherwise indicated, provide hinge pins as follows: 1. The metal doors and frames install machine screws into drilled and tapped holes. 2. The wood doors and frames install wood screws. 3. For fire-rated wood doors install #12 x 1-1/4”, threaded-to-the-head steel wood screws. 4. Finish screw heads to match surface of hinges or pivots. D. Number of Hinges: Provide number of hinges indicated but not less than 1 1/2 pair per door leaf for doors 90 inches or less in height and one additional hinge for each 30 inches of additional height. 1. Fire-Rated Doors: Not less than 3 hinges per door leaf for doors 86 inches of less in height with same rule for additional hinges. 1.8. Lock Cylinder and Keying A. The Contractor shall provide a new grandmaster key system for the Project and equip all locks with manufacturer’s special 6-pin tumbler cylinder with construction master key feature that permits voiding of construction keys without cylinder removal. B. The Contractor shall, except as otherwise indicated, provide individual change key for each lock that is not designated to be keyed alike with a group of related locks within the approved master keying system and permanently inscribe each key with number of lock that identifies cylinder manufacturer’s key symbol, and notation, “DO NOT DUPLICATE”. REV. MARCH 2006 249 © 2002, Fairmont Hotels and Resorts. All Rights Reserved.
Page 1 and 2:
FAIRMONT HOTELS & RESORTS · DESIGN
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Fairmont Hotels & Resorts · Design
Page 199 and 200:
Page 201 and 202:
Page 203 and 204: Fairmont Hotels & Resorts · Design
Page 253: Fairmont Hotels & Resorts · Design
Page 295: Fairmont Hotels & Resorts · Design
show all

FAIRMONT HOTELS &amp; RESORTS -DESIGN STANDARDS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

FAIRMONT HOTELS & RESORTS -DESIGN STANDARDS