Timken Industrial Seal Catalog

More documents

Recommendations

Info

Oil Seals Typical Seal Configurations Model 3 Model 21 Model 23 Model 24 Model 25 Model 26 Model 26-E Model 26-R1 Model 53 Model 53-F1 Model 53-G1 Model 53-R1 Model 53-R2 Model 53-T2 Model 53-TB Model 53-TF Model 54 Model 57 Model 58 Model 59 Model 59-G1 PS ® -1 PS ® -1 Dbl Opposed PS ® -1 Reverse Lip 10 Configuration Oil Seals PS ® -1 Dbl Tandem Model 62 Model 63 Model 63-F1 Model 63-G1 Model 63-R1 Model 63-R2 Model 63-T2 Model 63-TB Model 63-TF Model 64 Model 64-G1 Model 71 Model 76 Model 87 Model 88 Model 91 Model 92 Model 94 Model 111 Model 113 Model 123 Model 143 Model 145
Oil Seals Product Information Large Shaft Surface Spring Misalign. Features Materials Temperature Seals Diameter Speed Type in. @ f/m Pressure in. (mm) (mm@m/s) Model 26 Model 26R1 Model 59 Model 59G1 Model 64 ® Model 64G1 Model 87 Model 88 • General purpose seal • Solid or split design • Reverse bevel lip design prevents lip rollover • Reinforced rubber O.D. • Single and dual lip configurations available • General purpose dual lip seal • Low-speed service • Reverse bevel lip design prevents lip rollover • Severe service assembled seal • Heavy duty outer case • Reverse bevel lip design prevents lip rollover • Aggressive shaft-to-bore misalignment capability • Severe service dual lip assembled seal • GYLON ® excluder lip for nonlubricated external conditions or corrosive external conditions • Severe service assembled seal • Heavy duty metal outer case • Unique carrier/garter spring combination • Industry’s highest shaft-to-bore misalignement capability • Severe service dual lip assembled seal • GYLON ® • Timken N • Timken ES • Timken V -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) -22°F (-30°C) to 400°F (204°C) 0.750 to 60.000 (19.0 to 1524.0) 5,000 f/m Molded-in 0.015 @ 1,000 To 7 psi (25.4 m/s) stainless (0.38 @ 5.10) (0.4 bar) steel finger (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) 0.008 @ 5,000 (0.20 @ 25.40) • Timken N • Timken ES -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) 0.750 to 60.000 (19.0 to 1524.0) 5,000 f/m Molded-in 0.015 @ 1,000 To 7 psi (25.4 m/s) stainless (0.38 @ 5.10) (0.4 bar) steel finger (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) • Timken V -22°F (-30°C) to 400°F (204°C) 0.008 @ 5,000 (0.20 @ 25.40) • Timken N • Timken ES • Timken V -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) -22°F (-30°C) to 400°F (204°C) 6.000 to 90.000 (152.4 to 2286.0) 5,000 f/m Molded-in 0.015 @ 1,000 To 7 psi (25.4 m/s) stainless (0.38 @ 5.10) (0.4 bar) steel finger (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) 0.008 @ 5,000 (0.20 @ 25.40) • Timken N • Timken ES -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) 6.000 to 40.000 (152.4 to 1016.0) 2,500 f/m Molded-in 0.015 @ 1,000 To 7 psi (12.8 m/s) stainless (0.38 @ 5.10) (0.4 bar) steel finger (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) • Timken V -22°F (-30°C) to 400°F (204°C) 0.008 @ 5,000 (0.20 @ 25.40) • Timken N • Timken ES • Timken V -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) -22°F (-30°C) to 400°F (204°C) 8.000 to 90.000 (203.2 to 2286.0) 7,000 f/m Combination 0.015 @ 1,000 To 7 psi (35.6 m/s) of stainless (0.38 @ 5.10) (0.4 bar) steel garter (N/A if split) & stainless 0.010 @ 2,000 steel finger (0.25 @ 10.20) 0.008 @ 5,000 (0.20 @ 25.40) excluder lip for nonlubricated external conditions or corrosive external conditions • Timken N • Timken ES -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) 8.000 to 55.000 (203.2 to 1397.0) 3,500 f/m Carrier/ 0.015 @ 1,000 To 7 psi (17.9 m/s) garter (0.38 @ 5.10) (0.4 bar) combination (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) • Timken V -22°F (-30°C) to 400°F (204°C) 0.008 @ 5,000 (0.20 @ 25.40) • Severe service seal • Metal reinforced rubber O.D. • Reverse bevel lip design prevents lip rollover • Aggressive shaft-to-bore misalignment capability • Timken N • Timken ES • Timken V -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) -22°F (-30°C) to 400°F (204°C) 6.000 to 48.000 (152.4 to 1219.2) 5,000 f/m Molded-in 0.015 @ 1,000 To 7 psi (25.4 m/s) carbon (0.38 @ 5.10) (0.4 bar) steel garter (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) 0.008 @ 5,000 (0.20 @ 25.40) • Severe service seal • Aggressive shaft-to-bore misalignment capability • Metal reinforced rubber OD for positive bore retention • Timken N • Timken ES -40°F (-40°C) to 200°F (93°C) -40°F (-40°C) to 300°F (150°C) 6.000 to 48.000 (152.4 to 1219.2) 3,000 f/m Molded-in 0.015 @ 1,000 To 7 psi (15.2 m/s) carbon (0.38 @ 5.10) (0.4 bar) steel garter (N/A if split) 0.010 @ 2,000 (0.25 @ 10.20) • Timken V -22°F (-30°C) to 400°F (204°C) 0.008 @ 5,000 (0.20 @ 25.40) * Most designs available without spring. * Most designs available in silicone and other materials. 11
Page 1: Timken Industrial Seal Catalog High
Page 4 and 5: Introduction At Timken, customers t
Page 7 and 8: Technology Overview Turn to Timken
Page 9 and 10: Engineering Data Comparing Shaft Le
Page 11 and 12: Engineering Data Table 7: Shaft and
Page 13 and 14: Seals Installation Instructions Ins
Page 15: Seal & Material Selection Seal Sele
Page 19 and 20: Oil Seals Product Information Large
Page 21 and 22: Oil Seals Product Information Shaft
Page 23 and 24: Oil Seals Product Information Speci
Page 25 and 26: Bearing Isolators Configurations Bo
Page 27 and 28: Bearing Isolators Product Informati
Page 29 and 30: Glossary Width Assembled Seal made
Page 31 and 32: Oil Seals Appendix A - Product Iden
Page 37 and 38: Oil Seals Appendix B - Obsolete App
Page 39 and 40: Oil Seals Appendix C - Compound Com
Page 45 and 46: Oil Seals Appendix D - Failure Anal
Page 47 and 48: Oil Seals Appendix D - Failure Anal
Page 49: Relationship Between RPM, FPM and S
Page 52 and 53: M-2
Page 54 and 55: Oil Seals by Model Number Model Num
Page 56 and 57: Product Inches MM Model Code ID OD
Page 66 and 67:
Product Inches MM Model Code ID OD
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Product Inches MM Model Code From I
Page 219 and 220:
Seals by Shaft size
Page 221 and 222:
Using This Catalog The following pa
Page 223 and 224:
Oil Seals by Model Number Product I
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Face Seals by Model Number Product
Page 387 and 388:
Oil Seals by Model Number
show all

Timken Industrial Seal Catalog

Create successful ePaper yourself

Delete template?

Save as template?