SEAL SPECIFICATION GUIDE

More documents

Recommendations

Info

Part Part Number Width I.D. O.D. Number Width I.D. O.D. 443R 1/4 0.250 7-1/2 7.500 8 8.000 444R 1/4 0.250 7-3/4 7.750 8-1/4 8.250 445R 1/4 0.250 8 8.000 8-1/2 8.500 446R 1/4 0.250 8-1/2 8.500 9 9.000 447R 1/4 0.250 9 9.000 9-1/2 9.500 448R 1/4 0.250 9-1/2 9.500 10 10.000 449R 1/4 0.250 10 10.000 10-1/2 10.500 450R 1/4 0.250 10-1/2 10.500 11 11.000 451R 1/4 0.250 11 11.000 11-1/2 11.500 452R 1/4 0.250 11-1/2 11.500 12 12.000 453R 1/4 0.250 12 12.000 12-1/2 12.500 454R 1/4 0.250 12-1/2 12.500 13 13.000 455R 1/4 0.250 13 13.000 13-1/2 13.500 456R 1/4 0.250 13-1/2 13.500 14 14.000 457R 1/4 0.250 14 14.000 14-1/2 14.500 458R 1/4 0.250 14-1/2 14.500 15 15.000 459R 1/4 0.250 15 15.000 15-1/2 15.500 460R 1/4 0.250 15-1/2 15.500 16 16.000 198
<strong>SEAL</strong> TYPES 10S 20S 50S 40S 70S 260 290 300 310 320 330 340 350 360 400 410 430 440 450 460 540 560 570 590 610 960 970 980 990 1000 TPDW TW2 TW TW-H TFF TFW-H 80S 90S 410 430 440 450 460 470 480 490 510 520 690 700 710 720 740 750 760 780 790 830 860 870 880 890 900 910 920 930 940 620 640 650 2000 2000E 2010 2030 2040 2050 2300 2710 2720 2730 2740 2760 2770 2780 2790 2800 2810 2820 2830 2840 2850 2860 2870 2900 KEY 210 660 METAL RUBBER FELT TEFLON LEATHER 240 TDW-H 250 680
Page 1 and 2:
SSG SEAL SPECIFICATION GUIDE THE TI
Page 3 and 4:
TABLE OF CONTENTS SECTION. . . . .
Page 5 and 6:
SEAL DESIGN/TYPES 10S 20S 50S 40S 7
Page 7 and 8:
SHAFT RECOMMENDATIONS Shafts Seal a
Page 9 and 10:
BORE RECOMMENDATIONS Bore Diameter
Page 11 and 12:
OPERATING CONDITIONS Eccentricity S
Page 13 and 14:
MATERIAL SELECTION General Elastome
Page 15 and 16:
IMPROPER METHOD OF SEAL INSTALLATIO
Page 17 and 18:
KWIK-SLEEVE TM - COMPONENTS Put the
Page 19 and 20:
Part Part Shaft Bore O.D. Width Num
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Styles VS1, VS3, & VS4 Style VS2 Sh
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Shaft Bore O.D. Width Part Number T
Page 89 and 90:
Shaft Bore O.D. Width Part Number T
Page 91 and 92:
Shaft Diameter Width on Overall Fla
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Part Seal Shaft O.D. Width Number N
Page 99 and 100:
Part Seal Shaft O.D. Width Number N
Page 101 and 102:
Part Number Style Matl Shaft Bore O
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150: Part Number Style Matl Shaft Bore O
Page 153 and 154: Styles VS1, VS3, & VS4 Style VS2 Pa
Page 165 and 166: Shaft Diameter Range Width on Overa
Page 171 and 172: Part Seal Number Shaft O.D. Width N
Page 173 and 174: Part Seal Number Shaft O.D. Width N
Page 175 and 176: Shaft Bore O.D. Width Part Number S
Page 199: Part Part Number Width I.D. O.D. Nu
Page 203 and 204: NOTES 200
show all

SEAL SPECIFICATION GUIDE

Create successful ePaper yourself

Delete template?

Save as template?