Autodata - Diagnostic Trouble Codes Fault locations and probable causes - 2004 edition

05.02.2017 Views

I Transmission Model: Year: Avensis Fascia NOTE: Engine control module (ECM) incorporates transmission control function. General information Refer to the front of this manual for general test conditions, terminology, detailed descriptions of wiring faults and a general trouble shooter for electrical and mechanical faults. o Trouble codes are displayed by the 'OID OFF' warning lamp. 0 More detailed fault diagnosis information can be obtained using diagnostic equipment connected to the data link connector (DLC). Accessing Switch ignition ON. Check operation of 'OID OFF' lamp. Switch the OID switch on the gear lever to ON. Check that 'OID OFF' lamp extinguishes. Bridge data link connector (DLC) terminals 4 and 13 0. If no trouble codes are stored, the lamp will flash twice per second O. Each trouble code consists of two groups of one or more flashes El [A]. Warning lamp flash duration: 0,5 second El [B]. A 0,5 second pause separates each flash El [C]. A 1,5 second pause separates each trouble code group El [Dl. A 2,5 second pause separates each trouble code El [El. For example: Four 0,5 second flashes - 1,5 second pause - two 0,5 second flashes. Trouble code 42 displayed - vehicle speed sensor (VSS) 1. Trouble codes are repeated 4,5 seconds after last trouble code. Count warning lamp flashes. Compare with trouble code table. Remove bridge wire. Switch ignition OFF. Rectify faults as necessary. ON OFF 5

Erasing Ensure ignition switched OFF. Remove EFI fuse (15A) from underbonnet fusebox for 10 seconds minimum D. Refit fuse. Diagnostic equipment can also be used to erase data from ECM fault memory. Repeat accessing procedure to ensure trouble codes erased. Trouble codes may also be erased by disconnecting battery leads. WARNING: Disconnecting the battery may erase memory from electronic units (e.g. radio, clock). Trouble code identification

I<br />

Transmission<br />

Model:<br />

Year:<br />

Avensis<br />

Fascia<br />

NOTE: Engine control module (ECM) incorporates transmission<br />

control function.<br />

General information<br />

Refer to the front of this manual for general test conditions,<br />

terminology, detailed descriptions of wiring faults <strong>and</strong> a<br />

general trouble shooter for electrical <strong>and</strong> mechanical faults.<br />

o <strong>Trouble</strong> codes are displayed by the 'OID OFF' warning lamp.<br />

0 More detailed fault diagnosis information can be obtained<br />

using diagnostic equipment connected to the data link<br />

connector (DLC).<br />

Accessing<br />

Switch ignition ON.<br />

Check operation of 'OID OFF' lamp.<br />

Switch the OID switch on the gear lever to ON.<br />

Check that 'OID OFF' lamp extinguishes.<br />

Bridge data link connector (DLC) terminals 4 <strong>and</strong> 13 0.<br />

If no trouble codes are stored, the lamp will flash twice per<br />

second O.<br />

Each trouble code consists of two groups of one or more<br />

flashes El [A].<br />

Warning lamp flash duration: 0,5 second El [B].<br />

A 0,5 second pause separates each flash El [C].<br />

A 1,5 second pause separates each trouble code group El [Dl.<br />

A 2,5 second pause separates each trouble code El [El.<br />

For example: Four 0,5 second flashes - 1,5 second<br />

pause - two 0,5 second flashes. <strong>Trouble</strong> code 42<br />

displayed - vehicle speed sensor (VSS) 1.<br />

<strong>Trouble</strong> codes are repeated 4,5 seconds after last trouble<br />

code.<br />

Count warning lamp flashes. Compare with trouble code<br />

table.<br />

Remove bridge wire. Switch ignition OFF. Rectify faults as<br />

necessary.<br />

ON<br />

OFF 5

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!