Autodata - Diagnostic Trouble Codes Fault locations and probable causes - 2004 edition

05.02.2017 Views

I Engine management Trouble code identification I 00000 I No fault found - 00281 I Vehicle speed sensor (VSS) I Wiring, speedometer, VSS 00282 1 Idle speed control (ISC) actuator I Wiring, multi-plug incorrectly wired, ISC actuator 0051 5 rn 00516 00518 Crankshaft position (CKP) sensor Closed throttle position (CTP) switch Throttle position (TP) sensor 00522 I Enaine coolant temoerature (ECTI sensor I Wirina, poor connection. ECT sensor 00523 1 Intake air temperature (IAT) sensor I Wiring, IAT sensor 00525 00532 00537 00561 Heated oxygen sensor (H02S) Engine control module (ECM) - supply voltage Heated oxygen sensor (H02S) - lambda control Mixture control ( I Insecure rotor, wiring, CKP sensor Accelerator cable adjustment, wiring, CTP switch Wiring, poor connection, TP sensor Wiring, H02S, heating inoperative, fuel level low Battery, wiring Heating inoperative, exhaust leak, misfire, fuel pressure1 pump, EVAP canister purae valve Fuel level low, fuel pressurelpump, intakelexhaust leak, misfire, H02S, EVAP canister purge valve, injector, excessive fuel in engine oil 00670 1 Idle speed cOntrol (ISC) actuator position sensor I Wiring, throttle valve, ISC actuator position sensor 17978 Engine control module (ECM) immobiiizer active 65535 I Engine control module (ECM) lncorrectldamaged key, incorrectly coded, ECMl immobilizer replacement without coding, wiring, immobilizer defective ECM rn Trouble code may be displayed if engine is not idling during self-diagnosis due to missing CKP sensor signal. Ignore trouble code if engine starts. After repairs, erase learnt lambda control values as follows: Wait 30 seconds. Disconnect battery or ECM multi-plug for at least 30 seconds. Carry out road test to allow ECM to re-learn basic values.

Model: Arosa IbizalCordoba Toledo ToledolLeon Alhambra Year: 1991 -02 Transmission Arosa, lbtzalCordoba 1999-4 - in fascia fusebox Ibirat(=ordoba -4999 - driver's glovebox I I I Toledo -r03199 - adjacent to steering column I Toledo 03199 +, Leon - centre console Ahambra WOO -r - fascia, drivw's side

I<br />

Engine management<br />

<strong>Trouble</strong> code identification<br />

I<br />

00000 I No fault found -<br />

00281 I Vehicle speed sensor (VSS) I Wiring, speedometer, VSS<br />

00282 1 Idle speed control (ISC) actuator I Wiring, multi-plug incorrectly wired, ISC actuator<br />

0051 5 rn<br />

00516<br />

00518<br />

Crankshaft position (CKP) sensor<br />

Closed throttle position (CTP) switch<br />

Throttle position (TP) sensor<br />

00522 I Enaine coolant temoerature (ECTI sensor I Wirina, poor connection. ECT sensor<br />

00523 1 Intake air temperature (IAT) sensor I Wiring, IAT sensor<br />

00525<br />

00532<br />

00537<br />

00561<br />

Heated oxygen sensor (H02S)<br />

Engine control module (ECM) - supply voltage<br />

Heated oxygen sensor (H02S) - lambda control<br />

Mixture control (<br />

I<br />

Insecure rotor, wiring, CKP sensor<br />

Accelerator cable adjustment, wiring, CTP switch<br />

Wiring, poor connection, TP sensor<br />

Wiring, H02S, heating inoperative, fuel level low<br />

Battery, wiring<br />

Heating inoperative, exhaust leak, misfire, fuel pressure1<br />

pump, EVAP canister purae valve<br />

Fuel level low, fuel pressurelpump, intakelexhaust leak,<br />

misfire, H02S, EVAP canister purge valve, injector,<br />

excessive fuel in engine oil<br />

00670 1 Idle speed cOntrol (ISC) actuator position sensor I Wiring, throttle valve, ISC actuator position sensor<br />

17978<br />

Engine control module (ECM) immobiiizer active<br />

65535 I Engine control module (ECM)<br />

lncorrectldamaged key, incorrectly coded, ECMl<br />

immobilizer replacement without coding, wiring,<br />

immobilizer defective<br />

ECM<br />

rn <strong>Trouble</strong> code may be displayed if engine is not idling during self-diagnosis due to missing CKP sensor signal. Ignore trouble code if<br />

engine starts.<br />

After repairs, erase learnt lambda control values as follows: Wait 30 seconds. Disconnect battery or ECM multi-plug for at least<br />

30 seconds. Carry out road test to allow ECM to re-learn basic values.

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!