05.02.2017 Views

Autodata - Diagnostic Trouble Codes Fault locations and probable causes - 2004 edition

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

I Engine management<br />

Model: 3 SerieslCompact (E36) 3 Series (E46) 520i (E34)<br />

5 Series (E39) 7 Series (E38) 23<br />

Scanner<br />

type<br />

<strong>Fault</strong> location<br />

Probable cause<br />

189 Heated oxygen sensor (H02S) 1, bank 2 - Wiring, connector(s), H02S<br />

rangelperformance problem<br />

190<br />

Heated oxygen sensor (H02S) 2, bank 1 -<br />

rangelperformance problem<br />

Wiring, connector(s), H02S<br />

191 Heated oxygen sensor (H02S) 2, bank 2 - Wiring, connector(s), H02S<br />

rangelperformance problem<br />

200 / Engine control module (ECM) - defective Disconnect ECM multi-plug for at least 5 min. - check if<br />

trouble code reappears before replacing ECM<br />

204 I<br />

MS41: Heated oxygen sensor (H02S) 1 -<br />

circuit malfunction<br />

Heated oxygen sensor (H02S) 2 - circuit<br />

malfunction<br />

Heated oxygen sensor (H02S), cyl. 1-3 -<br />

rangelperformance problem<br />

Heated oxygen sensor (H02S), cyl. 4-6 -<br />

rangelperformance problem<br />

Idle speed control (ISC) actuatorlidle air control<br />

(IAC) valve - idle speed incorrect<br />

Immobilizer control modulelengine control<br />

module (ECM) - plausibility<br />

Immobilizer control module - incorrect signal<br />

Wiring, connector(s), H02S<br />

Wiring, connector(s), H02S<br />

Wiring, intakelexhaust leak, fuel level low, fuel pressure,<br />

evaporative emission (EVAP) canister purge valve,<br />

injector(s), H02S, ECM<br />

Wiring, intakelexhaust leak, fuel level low, fuel pressure,<br />

evaporative emission (EVAP) canister purge valve,<br />

injector(s), H02S, ECM<br />

Intake leak, ISC actuator1lAC valve, TP sensor, throttle valve<br />

Wiring, immobilizer control module, ECM<br />

Wiring, incorrectly coded, immobilizer control module<br />

210 I Misfire detected - more than 2 cylinders Wiring, ignition coils, spark plugs, ignition signal resistor,<br />

ECM<br />

Idle speed control (ISC) actuatorlidle air control ISC actuatorllAC valve<br />

(IAC) valve - mechanical fault<br />

Camshaft position (CMP) actuator -<br />

Camshaft timing mechanism, CMP actuator<br />

212 1 mechanical fault<br />

Vehicle speed sensor (VSS) - signal Wiring, ECMIABS control module communication, electrical<br />

214 1 interference, ABS trouble code(s) stored, ECM<br />

Engine control module (ECM)lABS control Wiring, electrical interference, ABS trouble code(s) stored,<br />

215 1 module communication - plausibility<br />

ECM<br />

MS42: Heated oxygen sensor (H02S) 2, Wiring, connector(s), H02S<br />

bank 1 - no signal<br />

I CAN data bus. TCM - signal<br />

Wiring, transmission range (TR) switch, electrical<br />

interference, TCM, ECM<br />

MS42: Heated oxygen sensor (H02S) 2, Wiring, connector(s), H02S<br />

bank 2 - no signal<br />

CAN data bus, TCM - no data transmission Wiring, electrical interference, TCM<br />

218 ( CAN data bus, ECM Wiring<br />

219<br />

220<br />

CAN data bus, ECM<br />

Heated oxygen sensor (H02S) 2, bank 1 -<br />

malfunction<br />

Heated oxygen sensor (H02S) 2, bank 2 -<br />

malfunction<br />

Wiring<br />

Wiring, connector(s), H02S<br />

Wiring, connector(s), H02S

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!