Chapter 8. Replacing FRUs - CNET Content Solutions
Chapter 8. Replacing FRUs - CNET Content Solutions Chapter 8. Replacing FRUs - CNET Content Solutions
98 Hardware Maintenance Manual cover and place it on the microprocessor socket of the failing system board when you complete this procedure. 18. Holding the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket on the new system board. Important To avoid damaging the microprocessor contacts, do not tilt the microprocessor when installing it into the socket. 19. Lower the microprocessor straight down into the system board socket of the new system board. 20. To secure the microprocessor in the socket, close the microprocessor retainer and lock it into position with the small handle. 21. Install the new retention module (if required) on the new system board. 22. Install the heat sink and fan assembly on the new system board. 23. Reconnect the heat sink and fan assembly cable to the system board. See the system board illustration for your machine type at “System board connectors” on page 88. 24. Install the new system board into the chassis and align the screw holes with those in the chassis. Insert and tighten the screws that secure the system board. 25. Reconnect all cables that were disconnected from the system board. 26. Reinstall the hard disk drive. See “Replacing the hard disk drive” on page 103. 27. Align the drive bay assembly with the two slots and rails on the sides of the chassis, reconnect the drive cables on the system board, and then slide the drive bay assembly towards the rear of the chassis until it snaps into position. 28. Reinstall the front bezel. 29. Reinstall any PCI adapter cards that were removed. 30. Position the fan duct on the heat sink fan. 31. Go to “Completing the FRU replacement” on page 111.
Replacing the microprocessor This procedure describes how to remove and replace the microprocessor. The procedure varies depending upon the machine type. Important The heat sink and microprocessor might be very hot. Make sure these components are cool enough to safely handle before continuing this procedure. 1. Remove the cover. See “Removing the cover” on page 89. 2. Lift the fan duct off the heat sink fan. 3. Disconnect the heat sink and fan assembly cable from the system board. See the system board illustration for your machine type at “System board connectors” on page 88. 4. Remove the four screws ▌1▐securing the heat sink and fan assembly to the system board. 5. Lift the heat sink and fan assembly off the system board. Place the heat sink on its side so that the thermal grease does not come in contact with anything. Note: You might have to gently twist the heat sink to free it from the microprocessor. Chapter 8. Replacing FRUs- Rocky computers 99
- Page 53 and 54: 7. When prompted, insert a blank, f
- Page 55 and 56: The Full Erase Hard Drive provides
- Page 57 and 58: Chapter 6. Using the Setup Utility
- Page 59 and 60: 3. Select the desired startup devic
- Page 61 and 62: Chapter 7. Symptom-to-FRU Index Har
- Page 63 and 64: Diagnostic Error Code FRU/Action 00
- Page 65 and 66: Diagnostic Error Code FRU/Action 00
- Page 67 and 68: Diagnostic Error Code FRU/Action 00
- Page 69 and 70: Diagnostic Error Code FRU/Action 01
- Page 71 and 72: Diagnostic Error Code FRU/Action 01
- Page 73 and 74: Diagnostic Error Code FRU/Action 01
- Page 75 and 76: Diagnostic Error Code FRU/Action 02
- Page 77 and 78: Diagnostic Error Code FRU/Action 07
- Page 79 and 80: Diagnostic Error Code FRU/Action 08
- Page 81 and 82: Diagnostic Error Code FRU/Action 17
- Page 83 and 84: Diagnostic Error Code FRU/Action 30
- Page 85 and 86: POST error codes Each time you powe
- Page 87 and 88: Miscellaneous error messages Messag
- Page 89 and 90: c. Memory modules d. Extended video
- Page 91 and 92: Chapter 8. Replacing FRUs (Types 70
- Page 93 and 94: Computer components The following i
- Page 95 and 96: Removing the cover Important Read C
- Page 97 and 98: 4. Using the blue handle▌1▐, li
- Page 99 and 100: Replacing the CMOS battery If the C
- Page 101 and 102: 7. Lift the power supply out of the
- Page 103: 12. Lift the heat sink and fan asse
- Page 107 and 108: Notes: a. Note the orientation of t
- Page 109 and 110: Replacing the hard disk drive Impor
- Page 111 and 112: Replacing an optical drive This pro
- Page 113 and 114: Replacing the power switch/LED asse
- Page 115 and 116: Replacing the system fan assembly T
- Page 117 and 118: Completing the FRU replacement Afte
- Page 119 and 120: Chapter 9. Replacing FRUs (Types 70
- Page 121 and 122: Computer components The following i
- Page 123 and 124: Removing the cover Important Read C
- Page 125 and 126: Replacing the power supply This pro
- Page 127 and 128: 11. Remove the four screws ▌1▐
- Page 129 and 130: 17. Lower the microprocessor straig
- Page 131 and 132: 5. Lift the heat sink and fan assem
- Page 133 and 134: 11. Lower the microprocessor straig
- Page 135 and 136: Replacing a PCI adapter This proced
- Page 137 and 138: Replacing the primary hard disk dri
- Page 139 and 140: 9. Align the drive cage pivot pin w
- Page 141 and 142: 4. Press the blue release button to
- Page 143 and 144: 10. Install the hard drive cage int
- Page 145 and 146: Replacing the diskette drive This p
- Page 147 and 148: 4. Install the new rear fan assembl
- Page 149 and 150: 6. Pull on the tips of the rubber m
- Page 151 and 152: Replacing the power switch/LED asse
- Page 153 and 154: Completing the FRU replacement Afte
98 Hardware Maintenance Manual<br />
cover and place it on the microprocessor socket of the failing system<br />
board when you complete this procedure.<br />
1<strong>8.</strong> Holding the microprocessor with your fingers, position the microprocessor so<br />
that the notches on the microprocessor are aligned with the tabs in the<br />
microprocessor socket on the new system board.<br />
Important<br />
To avoid damaging the microprocessor contacts, do not tilt the<br />
microprocessor when installing it into the socket.<br />
19. Lower the microprocessor straight down into the system board socket of the<br />
new system board.<br />
20. To secure the microprocessor in the socket, close the microprocessor retainer<br />
and lock it into position with the small handle.<br />
21. Install the new retention module (if required) on the new system board.<br />
22. Install the heat sink and fan assembly on the new system board.<br />
23. Reconnect the heat sink and fan assembly cable to the system board. See the<br />
system board illustration for your machine type at “System board connectors”<br />
on page 8<strong>8.</strong><br />
24. Install the new system board into the chassis and align the screw holes with<br />
those in the chassis. Insert and tighten the screws that secure the system<br />
board.<br />
25. Reconnect all cables that were disconnected from the system board.<br />
26. Reinstall the hard disk drive. See “<strong>Replacing</strong> the hard disk drive” on page<br />
103.<br />
27. Align the drive bay assembly with the two slots and rails on the sides of the<br />
chassis, reconnect the drive cables on the system board, and then slide the<br />
drive bay assembly towards the rear of the chassis until it snaps into position.<br />
2<strong>8.</strong> Reinstall the front bezel.<br />
29. Reinstall any PCI adapter cards that were removed.<br />
30. Position the fan duct on the heat sink fan.<br />
31. Go to “Completing the FRU replacement” on page 111.