Spaenaur

Inch and Metric
AVK Industrial Products
Produits Industriels «AVK»
Pouces et Métrique
STEEL C-1010 or C-1110
FINISH: CAD PLATE PER QQ-P-416 TYPE 1 CLASS 3
TECHNICAL DATA
The suggested hole size listed below works well in softer materials
but may have to be enlarged in certain types of plastic to prevent
splitting and in hard materials to allow the nut to pull up into the
sleeve. In plastic, simply increase the drill size until the insert holds
without splitting the plastic. In hard material, increase the hole size
to allow the nut to pull into the sleeve. It is recommended that the
insert be tested in the application before finalizing the hole size.
OPEN END
STYLE
A-W ®
SERIES
INSERT
KNURLED THREADED INSERTS
C
INCH SERIES (All Dimensions in Inches)
SPAENAUR Thread Manufacturer’s HOLE SIZE HD L D IL Hole Depth Unit
No. Size No. +.005-.000 ±.005 ±.015 Max. Max. Min. Pkg.
215-114 #6-32 AWS2-632 15/64 (.234) .255 .370 .233 .205 .40 100
215-115 #8-32 AWS2-832 17/64 (.266) .285 .370 .264 .205 .40 100
215-116 #10-24 AWS2-1024 19/64 (.297) .320 .370 .295 .205 .40 100
215-117 #10-32 AWS2-1032 19/64 (.297) .320 .370 .295 .205 .40 100
215-118 1/4-20 AWS2-420 25/64 (.391) .415 .515 .389 .275 .54 100
215-119 1/4-28 AWS2-428 25/64 (.391) .415 .515 .389 .275 .54 100
215-120 5/16-18 AWS2-518 17/32 (.531) .550 .615 .528 .325 .64 50
215-121 5/16-24 AWS2-524 17/32 (.531) .550 .615 .528 .325 .64 50
215-122 3/8-16 AWS2-616 19/32 (.594) .615 .740 .590 .390 .77 50
215-123 3/8-24 AWS2-624 19/32 (.594) .615 .740 .590 .390 .77 50
METRIC SERIES ±0.13 ±0.38
(All Dimensions in Millimetres)
216-062 M4x0.7 AWS2-470 6.75 7.24 9.40 6.71 5.21 10.16 100
216-063 M5x0.8 AWS2-580 7.54 8.13 9.40 7.50 5.21 10.16 100
216-064 M6x1.0 AWS2-610 9.92 10.54 13.08 9.88 6.99 13.72 100
216-065 M8x1.25 AWS2-8125 13.49 13.97 15.62 13.41 8.26 16.26 50
CATALOG 13
NOTE:
1. Use AVK recommended tooling for satisfactory installations.
2. Internal threads are manufactured oversize due to the mechanical function of the inserts and are
not able to be gauged before or after installation. However, they are always compatible with class 2 bolts.
ENGINEERING DATA
1. The AW series insert will protrude approximately .015" above the parent
materials unless special hole preparation is specified, see bottom of page.
2. The attachment screw is to be installed into the top of the insert, not the
blind side.
3. The component part being assembled is to be in contact with the head of
the insert (see sketch at top right). In most cases, when used in this
configuration, torque resistance of the insert surpasses those of high
strength bolts.
4. Application testing is recommended where GASKET material is used over
the insert.
5. The component part being attached shall not be allowed to rotate with the
bolt. Normally two or more bolts are used in an application which prevent
rotation of the component.
TECHNICALLY FLUSH INSTALLATIONS
Special hole preparation is required to produce a technically
flush application. Please refer to the sketch at right.
HD DIM
+ .025"
H DIM
EXTRUDED
The A-W Series Insert
should come in contact with
attached part.
STATIONARY
RECOMMENDED
NOT RECOMMENDED
WITHOUT TESTING.
HD DIM
+ .025"
H DIM
COUNTERBORED
90°
HD DIM
+ .025"
H DIM
COUNTERSUNK OR
STEP DRILLED
SEE TECHNICAL DATA FOR HD DIMENSION
Tel: 1-800-265-8772 Fax: 519-744-0818
C183