Spaenaur

C
AVK Test Data
Les données d'essai «AVK»
Inch and Metric
Pouces et Métrique
The test data on this page is intended to provide the designer with approximate strength values in various materials and
thicknesses. The figures shown are averages of multiple tests. AVK recommends that this data be used only as a guide since
various application factors may affect AVK product performance. We recommend testing your application when an exact
strength figure is required or the load to be applied comes close to the published data.
Thread size data is provided in pounds (LBS.) and Kilo-Newtons (KN) for force and inch pounds (INCH LBS.) and Newton
meters (Nm) for torque.
PULL-OUT is the force
required to pull the AVK
product from the parent
material. The parent material is
restrained by a hold down ring
3x the AVK part "D" dim.
A-S SERIES A-L/A-K SERIES
R-N SERIES A-H SERIES
C174
PUSH-OUT is the force SPIN-OUT is the torque
required to push the AVK required to turn the AVK
product through the parent product in the parent material
material. The parent material is after installation without
supported by a hold down ring influencing clamp load on the
3x the AVK part "D" dim AVK product.
A-L, A-K, A-H, A-S, product was tested with the -4 finish. R-N Series was Cadmium plated.
ASSEMBLY TORQUE is the
amount of torque suggested for
Grade 5 (Metric Class 8.0/9.9)
mating hardware based on
industry standards.
PULL-OUT PUSH-OUT SPIN-OUT
IN STEEL SHEET IN ALUMINUM SHEET IN STEEL STEEL ALUM
THREAD .030" .062" .090" .125" .030" .062" .090" .125" .125" .062" .062" ASSEMBLY
SIZE 0.76 mm 1.57 mm 2.28 mm 3.17 mm 0.76 mm 1.57 mm 2.28 mm 3.17 mm 3.17 mm 1.57 mm 1.57 mm TORQUE
6-32 316 817 1347 1952 276 898 1464 1604 12
8-32 316 773 1428 2000 275 828 1341 1571 22
10-24 473 971 1694 2127 325 964 1626 1967 32
10-32 473 971 1694 2127 325 964 1626 1967 36
1/4-20 570 1196 2244 2983 411 1157 2269 2892 75
5/16-18 703 2034 3066 4501 463 1435 2591 3896 156
3/8-16 703 1509 2551 4501 601 1554 2709 3850 276
1/2-13 NA 1693 2855 4480 NA 1866 3055 4184 660
M4 1.4 3.4 6.3 8.8 1.2 3.6 5.9 6.9 2.5
M5 2.1 4.3 7.5 9.4 1.4 4.2 7.2 8.7 5.0
M6 2.5 5.3 9.9 13.2 1.8 5.1 10.0 12.8 8.6
M8 3.1 9.0 13.6 20.0 2.0 6.3 11.5 17.3 21
M10 3.1 6.7 11.3 20.0 2.6 6.9 12.0 17.1 42
M12 NA 7.5 12.7 19.9 NA 8.3 13.5 18.6 72
6-32 284 735 NA 248 898 NA 37 40 12
8-32 284 696 NA 247 745 NA 36 39 22
10-24 426 874 1525 292 867 1463 69 71 32
10-32 426 874 1525 292 867 1463 69 71 36
1/4-20 513 1176 2020 369 1041 2042 130 143 75
5/16-16 633 1831 2759 416 1292 2332 190 186 156
3/8-16 633 1358 2296 541 1399 2438 190 188 276
M4 1.3 3.1 5.7 1.0 3.2 5.3 4.2 4.5 2.5
M5 1.9 3.9 6.7 1.2 3.8 6.4 7.8 8.0 5.0
M6 2.2 4.8 8.9 1.6 4.6 9.0 14.7 16.2 8.6
M8 2.8 8.1 12.2 1.8 5.6 10.3 21.5 21.0 21
M10 2.8 6.0 10.2 2.3 6.2 10.8 21.6 21.0 42
6-32 316 817 1437 1952 276 898 1464 1604 628 12
8-32 316 773 1428 2000 275 828 1341 1571 623 22
10-24 473 971 1694 2127 325 964 1626 1967 578 32
10-32 473 971 1694 2127 325 964 1626 1967 578 36
1/4-20 570 1196 2244 2983 411 1157 2269 2892 874 75
5/16-16 703 2034 3066 4501 463 1435 2591 3896 1134 156
3/8-16 703 1509 2551 4501 601 1554 2709 3850 1155 276
M4 1.4 3.4 6.3 8.8 1.2 3.6 5.9 6.9 2.7 2.5
M5 2.1 4.3 7.5 9.4 1.4 4.2 7.2 8.7 2.5 5.0
M6 2.5 5.3 9.9 13.2 1.8 5.1 10.0 12.8 3.8 8.6
M8 3.1 9.0 13.6 20.0 2.0 6.3 11.5 17.3 5.0 21
M10 3.1 6.7 11.3 20.0 2.6 6.9 20.0 17.1 5.1 42
1/4-20 347 854 1768 398 845 2100 1991 51 30 75
5/16-18 574 1201 2008 533 1106 2244 2688 70 46 156
3/8-16 623 1229 2041 585 1174 2110 3693 131 83 276
1/2-13 611 1314 2236 774 1385 2643 3877 300 130 660
M6 1.5 3.7 7.8 1.7 3.7 9.3 8.8 5.5 4.5 8.6
M8 2.5 5.3 8.9 2.6 2.9 9.9 11.9 7.2 5.9 21
M10 2.7 5.4 9.0 2.6 5.2 9.3 16.4 14.0 7.9 42
M12 2.7 5.8 9.9 3.4 6.1 11.7 17.2 37.9 26.6 72
CATALOG 13