Spaenaur

;
;
;;;
CATALOG 13
Pocket Pull ® Flush Handle
• Flush installation
• For lifting or pulling
• Lifting load transferred directly to panel edge
• Single-hole, screw-mount installation
22.4
(.88)
25.5
(1.00) 121.5 (4.78)
64.3
(2.53)
CUP
2.5 (.09)
PANEL THICKNESS
LIFT
46.7
(1.84)
Installation
1. Prepare a rectangular
opening as shown.
38 +0.2
-0.0
(1.500±.005)
114.30±0.25
(4.500±.010)
0.7 (.03) R MAX.
Product Strength
Guidelines
(Distributed Load)
23
(.90)
Lifting, Pulling
91.5 (3.60)
123 (4.84)
Maximum working load 1300 N (300 lbs.)
Average ultimate load 2700 N (600 lbs.)
Snap-in design
• Fast, efficient installation
• One-piece design
• Compact envelope
• For lifting or pulling
• Two sizes
• Low Gloss Black ABS
Product Strength Guidelines
(forces applied as shown)
*Based on installation in 1.2 mm
(.048 in.) steel panel.
Maximum loads limited by panel
strength.
Maximum. working load* = 1800 N (400 lbs.)
Average. ultimate load* = 5300 N (1200 lbs.)
2. Place pull in panel,
seating the slot
against top of
opening.
Matte Finish
on these
surfaces
INSTALLATION
1. Prepare a
rectangular
opening as
shown.
87.5±0.3 (3.45±.01)
30.7±0.15
(1.210±.005)
2. Engage edge of opening under flange
of pull.
3. Firmly snap in opposite flange with a
rocking motion.
SPAENAUR No's.
ABS, Black ABS, Black
UL94-HB UL94-VO
PANEL THICKNESS
1 (.040) MIN.
1.8 (.070) MAX.
097-439 —
Mfr. #P1-30-101-11
Pushing, Sliding
Maximum working load
450 N (100) lbs.
Average ultimate load
670 N (150) lbs.
127.3 (5.01) larger P2
132±0.3 (5.20±.01)
R MAX.
1.5 (.06)
Pulls and Door Retaining Springs
Poignées et Ressorts de retenue pour porte
Other Panel Thickness Range to 3.3 (.130)
available Special Order.
Material and Finish
PULL and CUP: ABS, black.
SCREWS: Steel, zinc plated plus bright
chromate dip.
82.5 (3.25) smaller P2
TYP. 5.3 (.21)
R 1 (.040) TYP.
NOTE:
Installation in a panel thickness less than the maximum
for each range allows some movement of the pull.
3. Attach cup to pull
and back of panel
with two screws
(supplied).
;;; yyy
Operating Temperature Range:
-50°C to 60°C (-60°F to 140°F)
Maximum recommended tightening torque for
mounting screws is 0.5 N•m (5 in.-lbs.)
R 1.5
(.06)
25.5
(1.00)
millimeter (inch)
Dimensions without tolerances
are for reference only.
Panel Thickness
Tel: 1-800-265-8772 Fax: 519-744-0818
;;; yyy
;;; yyy
35.8
(1.41)
17
(0.65)
40
(1.58)
REF.
1.8 (.07)
SPAENAUR No. PANEL THICKNESS
Large Small Min. Max.
097-444 097-440 1 (.040) 1.4 (.055)
Mfr. #P2-51 Mfr. #P2-41
097-445 097-441 1.4 (.055) 1.8 (.070)
Mfr. #P2-52 Mfr. #P2-42
097-446 097-442 1.8 (.070) 2.1 (.085)
Mfr. #P2-53 Mfr. #P2-43
097-447 097-443 2.1 (.085) 2.5 (.100)
Mfr. #P2-54 Mfr. #P2-44
Maximum working load* = 450 N (100 lbs.)
Average ultimate load* = 650 N (150 lbs.)
L141
L