1 - Electronic Instrument Service - Horological and Ultrasonic

Greiner vibrograf A.G.
Weststrasse 69
CH - 4900 Langenthal
Switzerland
Helmut Klein GmbH.
Steinenlandstrasse 1
DE - 75181 Pforzheim
Germany
Tel. ++41 62 923 44 33
Fax ++41 62 923 18 46
Email: greinervibrograf@datacomm.ch
Internet: www.greinervibrograf.com
User Manual
ACS - 900
Greiner
english
Tel. ++49 7231 9535 0
Fax ++49 7231 9535 95 Greiner
User Manual ACS-900

Contents
Contents ------------------------------------------------
Introduction ACS-900 -------------------------------
Loading of the jars -----------------------------------
Fixed cleaning programs---------------------------
Select your own cleaning program-------------
Display explanation --------------------------------
Programming ------------------------------------------
Programming ------------------------------------------
Start cleaning program-----------------------------
Placing a password ---------------------------------
Help --------------------------------------------------------
Accessories --------------------------------------------
Baskets --------------------------------------------------
User Manual ACS-900
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13-19
Page 1

Introduction ACS-900 Page 2
Unpack the ACS-900 and install it on the working place.
Open the front doors and remove all packing material inside the instrument.
1. Main switch off.
2. Connect the ACS-900 with the delivered powercable
to the Power socket.
Please observe the Voltage (230 or 115 Volts)
marked on the label.
3. Switch on the main power switch.
The basket - holder moves upwards, the turntable
turns to Pos. 5 in front and the bracket of basket
holder turns to front.
The Instrument is now in standby Position.
4. Press the „LOAD“ key on the keyboard to install
the Ultrasound and the glass jars.
Standby Position = Position 5 of turnable is in front. Bracket of basket holder
is in frontl. A arrow in the display is moving from left to right.
The machine is ready to start.
Caution :
Do not place anything on top to the instrument that can block the ventilation
The ventilator fan that evacuates the fumes during the cleaning process from the machine is
located on the top. When process is finished, ventilator stops automatically after 5 min.
Preparation of the baths
Pos. 1 = cleaning bath (with or without ultrasonic)
Pos. 2 = cleaning bath or 1st rinsing bath
Pos. 3 = rinsing bath
Pos. 4 = cleaning or lubrication bath
Pos. 5 = remains empty (drying position)
Take care not to exceed the maximum level of fluids indicated on the jar and ultrasonic.
(Quantity 0,55 l).
User Manual ACS-900

Loading of the jars
1. Press LOAD
2. Press ENTER
3. Put ultrasonic in Pos. 1
4. Press ENTER
5. Put jar in Pos. 2
6. Continue as discribed in point 2
till all the jars are installed
7. Press EXIT
8. Load the baskets with the parts you
want to clean, insert in lower
basket-holder and close fixture.
9. The machine is ready for service.
You can start a test.
for example: Programm 7
10. Press
11. Press
12. Press
LOAD
ENTER
ENTER
EXIT
CLEAN
7
ENTER
User Manual ACS-900
Display shows :
Next or Pos. 1 - 5
Basket holder moves upwards.
Page 3
Turntable turns to the Pos. 1
If you operate 1,2,3,4 or 5 instead of ENTER
the turntable turns directly to the
corresponding position.
If ultrasonic is not requested you can install
a cleaning jar instead.
Turntable turns to the nex Position,
Pos. 2
--
--
ACS-900 change over to standby position.
--
--
Display says,
Which clean program?
Display shows you datas in programm 7
Cleaning program 7 is running.

Fixed cleaning programs Page 4
Buttons 7 8 9
Descriptions of the programs :
Program 7
Position turntable
Cleaning time
in minutes
are fixed programs (factory set).
They can not be changed.
1 2 3 4 5 S US
7 > 3 0 - - 1 1 3 1 5 F 1 U
Spin drying time
Basket
Cold air
movement typ Drying time
Program 8
Programm 9
1 2 3 4 5 S US
8 > 3 0 - - 1 3 3 3 5 H 1 U
Warm air
Positions which are not used
1 2 3 4 5 S US
9 > 5 0 2 5 - - 3 3 5 H 1 U
User Manual ACS-900
Ultrasonic
TIME MODE
Ultrasonic yes
Warm air
1 Minute
Positions which are not used
TIME MODE
TIME MODE

Select your own cleaning program
Important: Button 1-6 can be used for cleaning procedures.
Programming of ACS 900 is possible in standby
status or during cleaning program.
Explanation of the settings :
Time
Acc
Time programming positions 1-5 ( 0 - 9 minutes )
0 = Position is inactiv
1 - 9 basket stays in the jar between 1-9 minutes
Movement typ of the basket 0 - 5
User Manual ACS-900
1 2 3
Page 5
5
4 6
0 = Basket turns slowly in one direction half of the time and in the
reverse direction the other half of the selected time. No agitation
1 = movements are very slowly and stretched
2 = movements are slowly and less strectched.
3 = mean movements
4 = quick and short movement
5 = very quick and very short movement.
Spin Spin 1 - 5 minutes
Spinning is effected in the upper part of the jars.
Selected time is between 1 – 5 minutes.
The selected time is for all jars.
Drying Drying (warm or cold)
US
H = warm air Switch on or off with button 1
F = cold air
Remark : When jar (4) is selected, temperature of warm air is already
in the right position when basket runs for drying
Ultrasound
Programming of ultrasound is effected with Pos. 1 of turntable. With
Button 1 you can switch on or off. Movement status 0 is suggested
during cleaning with ultrasonic.

Display explanation
When you press key and 1 of the keys
the programs which were entered are shown on the display as you can see in the
following example:
Position turntable
Button-No.
Cleaning time
in minutes
Page 6
CLEAN 1 9
1 2 3 4 5 S US
1 > 3 0 - - 1 1 3 1 5 F 1 U
Spining time
Basket
Cold air
movement typ Drying time
Position turntable
button-No.
Cleaning time
In minutes
1 2 3 4 5 S US
7 > 3 0 - - 1 1 3 1 5 H 1 -
User Manual ACS-900
Ultrasonic
TIME MODE
Ultrasonic yes
1 minute
Spining time
TIME MODE
Basket
Warm air
movement typ Drying time
Ultrasonic
Ultrassonic no
1 bis 5 minutes

Programming Page 7
Key application display Indication Remark
PROG
1
ENTER
5
0
ENTER
4
1
ENTER
4
2
ENTER
6
3
ENTER
9
ENTER
ENTER
ENTER
ENTER
Which clean Program ?
1 > -- -- -- -- -- 1 -
Pos 1 > Time: # Acc: #
Pos 1 > Time: 5 Acc: #
Pos 1 > Time: 5 Acc: 0
Pos 2 > Time: # Acc: #
Pos 2 > Time: 4 Acc: #
Pos 2 > Time: 4 Acc: 1
Pos 3 > Time: # Acc: #
Pos 3 > Time: 4 Acc: #
Pos 3 > Time: 4 Acc: 2
Pos 4 > Time: # Acc: #
Pos 4 > Time: 6 Acc: #
Pos 4 > Time: 6 Acc: 3
Pos 5 > Time: 0
Pos 5 > Time: 9
User Manual ACS-900
Which program ?
Time pos. 1
Movement typ
Time pos. 2
Movement typ
Time pos. 3
Movement typ
Time pos. 4
Movement typ
Time pos. 5
See next page

Programming with button 1 1 ( exampel)
Page 8
Key application display indication Remark
ENTER
ENTER
ENTER
1
ENTER
1
Fan : OFF 1. ON
Heat : OFF 1. ON
Spin btwn stations : #
Spin btwn stations : 1
US : OFF 1. ON
US : ON 1. OFF
EXIT > > > > > > > > > > > > > >
PROG Which clean Program ?
1
1 2 3 4 5 S US
1 > 5 0 4 1 4 2 6 3 9 H 1 U
By pressing button 1, fan
for drying is activated or
deactivated.
By pressing button 1,
heat for drying is
activated or deactivated.
Spining time
1 bis 5 minutes
By pressing button 1,
ultrasonic is activated or
desactivated.
Arrow to the right
For controlling fixed
programs.
TIME MODE
Is cleaning program of button 1 correct ? 1 If yes,
EXIT
> > > > > > > > > > > > > >
Programming of button is installed and stored.
Programming of button + can be done in the same
way. On page 5 you will find all the adjustments which are possible.
1
2 6
User Manual ACS-900

Start cleaning program Page 9
Key application Display indication
Press button
Press button
Press button
1 9
ENTER
CLEAN
Interruption Cleaning program:
You can interrupt cleaning at any time.
1. Press button BREAK
2. Press button EXIT
User Manual ACS-900
Which clean Program ?
Indication of the dates from
the selected program.
Cleaning program is started
and whole run time is
Indicated.

Placing a password Page 10
Only the person who knows the password is able to change the cleaning program.
Any password can be used.
Installation can be done during standby-modus or cleaning program.
Enter a password for the first time:
Key application Display indication Remark
PROG
0
ENTER
1 9
ENTER
1 9
ENTER
Clear the password:
0
1
Which clean Program ?
Change password :
Enter new password :
Enter your personal
password
Code, max. 8 digits
Enter new pw again : Enter new pw again
Difference, new try :
Key application Display indication Remark
0
ENTER
7
Service, WELCOME !!!
User Manual ACS-900
Which program ?
In case of a mistake, enter
right no.
Now pw is installed and
stored.
Welcome to the service
program
The password is cleared

Assistance Page 11
The ultrasonic does not work.
Please check if the ultrasonic is installed as follows:
0
3
Key Display indication Remark
1
0
ENTER
Or
7
Service, WELCOME !!!
US uninst, 1, Toggle
US inst, 1 , Toggle
US inst, 1 , Toggle
Welcome to the service
program
Ultrasonic is not installed
Ultrasonic is installed
Press button 1
Indication is changing
between US inst and US
uninst
Press button 1 till display indication shows you (US inst, 1, Toggle).
Press button
exit
Check and reinstall programs 1 to 6 as required.
User Manual ACS-900

Accessories Page 12
Ultraschall
17142
17136
cover
couvercle
Deckel
17135
Glass jar
bocal en verre
Glaswanne
User Manual ACS-900
230 V = 17102
110 V = 17101
17938
Wave - breaker
Brise - remous
Wellenbrecher
for basket up to ø 80
pour panier jusqu‘à ø80
für Korb bis ø 80
US Generator
Print

Accessories
Ø 80 mm
17099
17098
15851
15852
15850
15848
15853
15849
Art. Nr
No.d’art.
part No.
10
17090
17092
17091
17132
17129
17128
17128
17127
17090
User Manual ACS-900
6
14
Ø 60 mm
Zubehör zu ACS900
Accessoires ACS900
Accessories ACS900
17122
17123
1 x 17122
5 x 17123
22
13
17131
Page 13
17134
20