combined small
TECHNICAL DATA SHEET SOLIDFIX FS WEARING COMPOUND 17 August 2016, Rev 2 TECHNICAL DETAILS: No of components : 2 Chemical resistance : Acids and alkalis, aliphatic solvents and petroleum products Mixing Ratio by volume: 2:1 by volume Pot Life (500ml) : 15 – 17 min at 25 degC Touch Dry : 1 hours Practical cure : 2 - 3 hours Full Cure : 18hrs Apply by : Trowel or gloved hand Theoretical Coverage : 6 ltr/m2 at 6mm Hardness : Shore D 85 Compressive Strength : 100 Mpa ASTM D-695-54 Tensile Strength : 35 Mpa Lap shear : > 13 Mpa Heat Deflection Temp : 70 Degrees C Volume Solids : 100% Application Temp : Minimum 5 Degrees C & Maximum 35 Degrees C Cleaner : Epoxy Thinners Shelf Life : 12 month Health and safety: All PPE must be worn at all times. Please consult the relevant Health & Safety Data Sheet available from Technical Finishes KZN on request and sent with each delivery. Safety Precautions: Ensure adequate ventilation in work area. Use protective clothing to avoid skin contact with uncured compound at all times. No sparks or naked flame to be permitted in the vicinity while tools and equipment are being cleaned with Epoxy Thinners or other flammable products. Important Note Technical Finishes products are guaranteed against defective materials and manufacture and are sold subject to its standard Terms and Conditions of Sale, copies of which can be obtained on request. Page 2 of 2 Gauteng Kwa-Zulu Natal Western Cape 35 Activia Rd, Activia Park, Germiston, 1610 41 Circuit Rd, Westmead 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 7475 Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455
TECHNICAL DATA SHEET SOLIDWEAR HP 100 1 July 2016, Rev 2 SOLIDWEAR HP 100 High Performance Epoxy Wearing Compound DESCRIPTION Solidwear HP100 is a high performance technically advanced epoxy wearing compound containing graded hi Alumina ceramic bead fillers, held uniformly in suspension in a blended high performance epoxy resin system to provide a long lasting lining to plant and equipment subject to a high degree of abrasive wear. Benefits: Excellent acid resistance > 70% Sulphuric acid. Strong acid blends typically used in mine processing. Cuts down time to a minimum, as most repairs are done on site. Extends life of costly plant and components. Easy to mix and apply. It conforms and spreads easily into tight corners and curved surfaces. Can be applied to vertical and overhead surfaces and areas in which compound shapes or difficult access make the application of other wearing materials impractical. Water smoothable – Lightly wetting trowel or gloved hand gives a smooth finish. Rapid Cure- Normally ready to use in 12 hrs hours at normal room temperature- less if heat is applied. Excellent adhesion to metal and other surfaces under adverse conditions including damp surfaces. Good low temperature cure down to 5 Degrees C and excellent corrosion resistance. Uses: Any plant and equipment subject to erosion caused by abrasion from process materials. Common areas of application are feed chutes, spigots, pipe elbows, slurry lines, hoppers, chests, settling tanks, cyclones pump casings ect. Substrate requirements: Surfaces to be clean, dry and free of rust or mill scale. Grit blasting is recommended. If mechanical grinding is used ensure that prepared surface has a rough profile. Application: Using a steel trowel or gloved hand apply compound at 4mm-6mm thickness or as specified. Wipe smooth with hands, which are slightly wet with soapy water. Any mixed material will become unusable after 40 minutes. To accelerate curing time post cure after compound has gardened by heating to about 40 Degrees C for 30 minutes. Resistance Resists dilute acids and alkalis, aliphatic solvents and petroleum products, seawater and distilled water. Page 1 of 2 Gauteng Kwa-Zulu Natal Western Cape 35 Activia Rd, Activia Park, Germiston, 1610 41 Circuit Rd, Westmead, 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1, 7475 Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455
- Page 1: Corrosion ProteCtion P O L Y S C R
- Page 4 and 5: STEEL PROTECTION PRODUCT NAME DESCR
- Page 6 and 7: P O L Y S C R E E D Corrolam solidg
- Page 8 and 9: Mining Products INDEX Technical Fin
- Page 10 and 11: TECHNICAL DATA SHEET SOLIDGUARD 88
- Page 12 and 13: TECHNICAL DATA SHEET Eposhield HCP
- Page 14 and 15: TECHNICAL DATA SHEET Eposhield ST 1
- Page 16 and 17: TECHNICAL DATA SHEET Corrolam VEP G
- Page 18 and 19: TECHNICAL DATA SHEET SOLIDGUARD LV
- Page 22 and 23: TECHNICAL DATA SHEET SOLIDWEAR HP 1
- Page 24 and 25: TECHNICAL DATA SHEET SOLIDWEAR HP 5
- Page 26 and 27: TECHNICAL DATA SHEET SOLIDWEAR HP 8
- Page 28 and 29: TECHNICAL DATA SHEET SOLIDBOND QSP
- Page 30 and 31: TECHNICAL DATA SHEET SOLIDBACK HP 1
- Page 32 and 33: TECHNICAL DATA SHEET SOLIDBACK ST 1
- Page 34 and 35: MATERIAL SAFETY DATA SHEET SOLIDGUA
- Page 36 and 37: MATERIAL SAFETY DATA SHEET SOLIDGUA
- Page 38 and 39: MATERIAL SAFETY DATA SHEET 5 Progre
- Page 40 and 41: MATERIAL SAFETY DATA SHEET SOLIDGUA
- Page 42 and 43: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 44 and 45: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 46 and 47: MATERIAL SAFETY DATA SHEET 41 Circu
- Page 48 and 49: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 50 and 51: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 52 and 53: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 54 and 55: MATERIAL SAFETY DATA SHEET 41 Circu
- Page 56 and 57: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 58 and 59: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 60 and 61: MATERIAL SAFETY DATA SHEET SOLIDWEA
- Page 62 and 63: MATERIAL SAFETY DATA SHEET 41 Circu
- Page 64: MATERIAL SAFETY DATA SHEET SOLIDWEA
TECHNICAL DATA SHEET<br />
SOLIDFIX FS WEARING COMPOUND<br />
17 August 2016, Rev 2<br />
TECHNICAL DETAILS:<br />
No of components : 2<br />
Chemical resistance : Acids and alkalis, aliphatic solvents and petroleum products<br />
Mixing Ratio by volume: 2:1 by volume<br />
Pot Life (500ml) : 15 – 17 min at 25 degC<br />
Touch Dry<br />
: 1 hours<br />
Practical cure : 2 - 3 hours<br />
Full Cure<br />
: 18hrs<br />
Apply by<br />
: Trowel or gloved hand<br />
Theoretical Coverage : 6 ltr/m2 at 6mm<br />
Hardness : Shore D 85<br />
Compressive Strength : 100 Mpa ASTM D-695-54<br />
Tensile Strength : 35 Mpa<br />
Lap shear<br />
: > 13 Mpa<br />
Heat Deflection Temp : 70 Degrees C<br />
Volume Solids : 100%<br />
Application Temp : Minimum 5 Degrees C & Maximum 35 Degrees C<br />
Cleaner<br />
: Epoxy Thinners<br />
Shelf Life<br />
: 12 month<br />
Health and safety:<br />
All PPE must be worn at all times. Please consult the relevant Health & Safety Data Sheet available from<br />
Technical Finishes KZN on request and sent with each delivery.<br />
Safety Precautions:<br />
Ensure adequate ventilation in work area. Use protective clothing to avoid skin contact with uncured<br />
compound at all times. No sparks or naked flame to be permitted in the vicinity while tools and equipment<br />
are being cleaned with Epoxy Thinners or other flammable products.<br />
Important Note<br />
Technical Finishes products are guaranteed against defective materials and manufacture and are sold<br />
subject to its standard Terms and Conditions of Sale, copies of which can be obtained on request.<br />
Page 2 of 2<br />
Gauteng Kwa-Zulu Natal Western Cape<br />
35 Activia Rd, Activia Park, Germiston, 1610 41 Circuit Rd, Westmead 3610 Cnr. Gunners Circle & Fisher Ave, Epping 1,<br />
7475<br />
Tel: +27 (0) 11 822 7242 Tel: +27 (0) 31 705 7733 Tel: +27 (0) 21 535 4455
Change language