Understanding API ICP653 Reading 15-Worksheet-11a
Q7. Welder's and welding operators who pass the tests for groove welds are qualified for what groove and fillet weld positions? (a) The positions of groove and fillet welds shown in QW-461.9. (b) In all thicknesses of material, sizes of fillet welds, and diameters of pipe and tube 2 7/8" and less. (c) In all thicknesses of material sizes of fillet welds, and diameters of pipe and tube 2-7/8" and over. ANS: A Q8. The three methods by which a welder or welding operator may be qualified are __ of initial production weld, radiography of____ or____ taken from a test coupon. (a) radiography-test coupon-bend tests (b) bend tests -test coupon-tension tests (c) tension tests-test coupon-bend tests ANS: A Charlie Chong/ Fion Zhang
Q9. What welding positions on pipe test coupons omit the specimens in the upper right and lower left quadrants, and replaces the root bend specimen in the upper left quadrant with a face-bend? (a) 2G or 5G (b) 1G or 2G (c) 5G or 6G ANS: Q10. What are the immediate retests required if a welder fails the mechanical tests of QW-302.1 or radiography examination of QW-302.2? . (a) Mechanical tests. (b) Mechanical tests and radiographic examination respectively. (c) Radiographic examination. ANS: b Charlie Chong/ Fion Zhang
- Page 19 and 20: TASK# 1 Read the following paragrap
- Page 21 and 22: Q5. Where are notch-toughness requi
- Page 23 and 24: Q9. How is the minimum specimen cur
- Page 25 and 26: Q13. Procedure and performance macr
- Page 27 and 28: Charlie Chong/ Fion Zhang #2
- Page 29 and 30: QW-191.1 Radiographic Examination Q
- Page 31 and 32: Q3. When may longitudinal-bend test
- Page 33 and 34: QW-100.3 Welding Procedure Specific
- Page 35 and 36: Q8. What are the test orientations
- Page 37 and 38: Task#2 Ref Para. 1. A QW-10()3 2. B
- Page 39 and 40: Reading: General Requirements QW-10
- Page 41 and 42: Q5. What constitutes a "set" of red
- Page 43 and 44: Q7. The WPS must list ___ variables
- Page 45 and 46: Task#3 Ref Para 1. A QW-484 2. C QW
- Page 47 and 48: Reading: Procedure Qualifications Q
- Page 49 and 50: Q5. The qualification of the ___is
- Page 51 and 52: QW-200.4 (b) For GTAW, SMAW, GMAW,
- Page 53 and 54: Charlie Chong/ Fion Zhang #5
- Page 55 and 56: QW-200.4 Combination of Welding Pro
- Page 57 and 58: Discussion: GTAW PQR variables: T=1
- Page 59 and 60: Q5. What limitation is invoked when
- Page 61 and 62: Q9: An organization's operational c
- Page 63 and 64: Q12. The ____ is a true record of t
- Page 65 and 66: Charlie Chong/ Fion Zhang #6
- Page 67 and 68: Reading: Performance Qualifications
- Page 69: Q5. How are the thickness limits de
- Page 73 and 74: QW-304 Welders Except for the speci
- Page 75 and 76: TASK#7 Reading: Performance Qualifi
- Page 77 and 78: Q5. Why is the Manufacturer respons
- Page 79 and 80: Q9. When performance qualification
- Page 81 and 82: Q13. Failure of any portion of a co
- Page 83 and 84: Charlie Chong/ Fion Zhang #8
- Page 85 and 86: TASK#8 Welding Data QW-400 thru QW-
- Page 87 and 88: Q2. Under what conditions may a WPS
- Page 89 and 90: Q6. A change in a welding condition
- Page 91 and 92: Q8. The grouping of ____and____ by
- Page 93 and 94: Charlie Chong/ Fion Zhang #9
- Page 95 and 96: TASK#9 Welding Data QW-451 thru QW-
- Page 97 and 98: Q3. In reviewing the form QW-483 (P
- Page 99 and 100: Q5. The SAW process is commonly cla
- Page 101 and 102: ASME SECTION IX PRACTICE QUESTIONS
- Page 103 and 104: Q5. New Welding Procedure Specifica
- Page 105 and 106: Q9. A welder qualifying with plate
- Page 107 and 108: Q12. Charpy V-notch tests are perfo
- Page 109 and 110: Q17. A WPS must describe: A. Essent
- Page 111 and 112: Q21. For the SAW process ______ is
- Page 113 and 114: Q26. Immediate retests of welders q
- Page 115 and 116: QW-452 Performance Qualification Th
- Page 117 and 118: QW-430 F-NUMBERS QW-431 General The
- Page 119 and 120: Q32. Ferrous weld metal chemical co
Q9. What welding positions on pipe test coupons omit the specimens in the<br />
upper right and lower left quadrants, and replaces the root bend specimen in<br />
the upper left quadrant with a face-bend?<br />
(a) 2G or 5G<br />
(b) 1G or 2G<br />
(c) 5G or 6G<br />
ANS:<br />
Q10. What are the immediate retests required if a welder fails the mechanical<br />
tests of QW-302.1 or radiography examination of QW-302.2? .<br />
(a) Mechanical tests.<br />
(b) Mechanical tests and radiographic examination respectively.<br />
(c) Radiographic examination.<br />
ANS: b<br />
Charlie Chong/ Fion Zhang