Understanding API ICP653 Reading 15-Worksheet-11a
QW-151-1(c) (c) When multiple specimens are used, in lieu of full thickness specimens, each set shall represent a single tension test of the full plate thickness. Collectively, all of the specimens required to represent the full thickness of the weld at one location shall comprise a set. (d) When multiple specimens are necessary, the entire thickness shall be mechanically cut into a minimum number of approximately equal strips of a size that can be tested in the available equipment. Each specimen of the set shall be tested and meet the requirements of QW-153. 1/3T x 3 plate thickness T, full plate thickness Charlie Chong/ Fion Zhang
Q7. The WPS must list ___ variables, while the PQR must list __ _ (a) essential, nonessential, I essential, supplementary essential (b) essential, nonessential and acceptable ranges, supplementary (when required) / essential, supplementary (when required) (c) essential/ nonessential, supplementary essential ANS: b Q8. The cut surfaces of guided-bend test specimens are designated____of the specimen, while the other two surfaces are called the ____and ____ surfaces. (a) sides-face-root (b) face-root-side (c) root-side-face ANS: a Charlie Chong/ Fion Zhang
- Page 1 and 2: Charlie Chong/ Fion Zhang
- Page 3 and 4: Expert at Works Charlie Chong/ Fion
- Page 5 and 6: Expert at Works Charlie Chong/ Fion
- Page 7 and 8: Charlie Chong/ Fion Zhang Fion Zhan
- Page 9 and 10: The Magical Book of Tank Inspection
- Page 11 and 12: API 653 Exam Administration -- Publ
- Page 13 and 14: • API Recommended Practice 575, I
- Page 15 and 16: Charlie Chong/ Fion Zhang
- Page 17 and 18: ASME SECTION IX EXERCISES Charlie C
- Page 19 and 20: TASK# 1 Read the following paragrap
- Page 21 and 22: Q5. Where are notch-toughness requi
- Page 23 and 24: Q9. How is the minimum specimen cur
- Page 25 and 26: Q13. Procedure and performance macr
- Page 27 and 28: Charlie Chong/ Fion Zhang #2
- Page 29 and 30: QW-191.1 Radiographic Examination Q
- Page 31 and 32: Q3. When may longitudinal-bend test
- Page 33 and 34: QW-100.3 Welding Procedure Specific
- Page 35 and 36: Q8. What are the test orientations
- Page 37 and 38: Task#2 Ref Para. 1. A QW-10()3 2. B
- Page 39 and 40: Reading: General Requirements QW-10
- Page 41: Q5. What constitutes a "set" of red
- Page 45 and 46: Task#3 Ref Para 1. A QW-484 2. C QW
- Page 47 and 48: Reading: Procedure Qualifications Q
- Page 49 and 50: Q5. The qualification of the ___is
- Page 51 and 52: QW-200.4 (b) For GTAW, SMAW, GMAW,
- Page 53 and 54: Charlie Chong/ Fion Zhang #5
- Page 55 and 56: QW-200.4 Combination of Welding Pro
- Page 57 and 58: Discussion: GTAW PQR variables: T=1
- Page 59 and 60: Q5. What limitation is invoked when
- Page 61 and 62: Q9: An organization's operational c
- Page 63 and 64: Q12. The ____ is a true record of t
- Page 65 and 66: Charlie Chong/ Fion Zhang #6
- Page 67 and 68: Reading: Performance Qualifications
- Page 69 and 70: Q5. How are the thickness limits de
- Page 71 and 72: Q9. What welding positions on pipe
- Page 73 and 74: QW-304 Welders Except for the speci
- Page 75 and 76: TASK#7 Reading: Performance Qualifi
- Page 77 and 78: Q5. Why is the Manufacturer respons
- Page 79 and 80: Q9. When performance qualification
- Page 81 and 82: Q13. Failure of any portion of a co
- Page 83 and 84: Charlie Chong/ Fion Zhang #8
- Page 85 and 86: TASK#8 Welding Data QW-400 thru QW-
- Page 87 and 88: Q2. Under what conditions may a WPS
- Page 89 and 90: Q6. A change in a welding condition
- Page 91 and 92: Q8. The grouping of ____and____ by
Q7. The WPS must list ___ variables, while the PQR must list __ _<br />
(a) essential, nonessential, I essential, supplementary essential<br />
(b) essential, nonessential and acceptable ranges, supplementary (when<br />
required) / essential, supplementary (when required)<br />
(c) essential/ nonessential, supplementary essential<br />
ANS: b<br />
Q8. The cut surfaces of guided-bend test specimens are designated____of<br />
the specimen, while the other two surfaces are called the ____and ____<br />
surfaces.<br />
(a) sides-face-root<br />
(b) face-root-side<br />
(c) root-side-face<br />
ANS: a<br />
Charlie Chong/ Fion Zhang