Understanding API ICP653 Reading 15-Worksheet-11a

More documents

Recommendations

Info

Q3: The open defects for guided-bend test specimen of the convex surface of the weld or heat affected zone shall not exceed ____ (a) 1/16". (b) 1/8" (c) 3/16“ ANS: b Q4. The PQR qualification test determines the ___ of the___ but not the ___ of the welder or welding operator. (a) properties-weldment-skill (b) skill-welder-qualification (c) qualification-welder-skill ANS: a Charlie Chong/ Fion Zhang
Q5. What constitutes a "set" of reduced multiple section specimens for plate or pipe tension tests? (a) Strips of equal size that can be tested in the available equipment. (b) All specimens representing the full thickness of the weld at one location. (c) All specimens representing half the thickness ofthe weld at one location. ANS: a Q6. What is the purpose of the welder's performance qualification? (a) To determine the welder's ability to operate the equipment. (b) To determine the mechanical properties of the weldment. (c) To determine the welder's ability to deposit sound weld metal. ANS: c Charlie Chong/ Fion Zhang
Page 1 and 2: Charlie Chong/ Fion Zhang
Page 3 and 4: Expert at Works Charlie Chong/ Fion
Page 5 and 6: Expert at Works Charlie Chong/ Fion
Page 7 and 8: Charlie Chong/ Fion Zhang Fion Zhan
Page 9 and 10: The Magical Book of Tank Inspection
Page 11 and 12: API 653 Exam Administration -- Publ
Page 13 and 14: • API Recommended Practice 575, I
Page 15 and 16: Charlie Chong/ Fion Zhang
Page 17 and 18: ASME SECTION IX EXERCISES Charlie C
Page 19 and 20: TASK# 1 Read the following paragrap
Page 21 and 22: Q5. Where are notch-toughness requi
Page 23 and 24: Q9. How is the minimum specimen cur
Page 25 and 26: Q13. Procedure and performance macr
Page 27 and 28: Charlie Chong/ Fion Zhang #2
Page 29 and 30: QW-191.1 Radiographic Examination Q
Page 31 and 32: Q3. When may longitudinal-bend test
Page 33 and 34: QW-100.3 Welding Procedure Specific
Page 35 and 36: Q8. What are the test orientations
Page 37 and 38: Task#2 Ref Para. 1. A QW-10()3 2. B
Page 39: Reading: General Requirements QW-10
Page 43 and 44: Q7. The WPS must list ___ variables
Page 45 and 46: Task#3 Ref Para 1. A QW-484 2. C QW
Page 47 and 48: Reading: Procedure Qualifications Q
Page 49 and 50: Q5. The qualification of the ___is
Page 51 and 52: QW-200.4 (b) For GTAW, SMAW, GMAW,
Page 55 and 56: QW-200.4 Combination of Welding Pro
Page 57 and 58: Discussion: GTAW PQR variables: T=1
Page 59 and 60: Q5. What limitation is invoked when
Page 61 and 62: Q9: An organization's operational c
Page 63 and 64: Q12. The ____ is a true record of t
Page 67 and 68: Reading: Performance Qualifications
Page 69 and 70: Q5. How are the thickness limits de
Page 71 and 72: Q9. What welding positions on pipe
Page 73 and 74: QW-304 Welders Except for the speci
Page 75 and 76: TASK#7 Reading: Performance Qualifi
Page 77 and 78: Q5. Why is the Manufacturer respons
Page 79 and 80: Q9. When performance qualification
Page 81 and 82: Q13. Failure of any portion of a co
Page 85 and 86: TASK#8 Welding Data QW-400 thru QW-
Page 87 and 88: Q2. Under what conditions may a WPS
Page 89 and 90: Q6. A change in a welding condition
Page 91 and 92:
Q8. The grouping of ____and____ by
Page 93 and 94:
Charlie Chong/ Fion Zhang #9
Page 95 and 96:
TASK#9 Welding Data QW-451 thru QW-
Page 97 and 98:
Q3. In reviewing the form QW-483 (P
Page 99 and 100:
Q5. The SAW process is commonly cla
Page 101 and 102:
ASME SECTION IX PRACTICE QUESTIONS
Page 103 and 104:
Q5. New Welding Procedure Specifica
Page 105 and 106:
Q9. A welder qualifying with plate
Page 107 and 108:
Q12. Charpy V-notch tests are perfo
Page 109 and 110:
Q17. A WPS must describe: A. Essent
Page 111 and 112:
Q21. For the SAW process ______ is
Page 113 and 114:
Q26. Immediate retests of welders q
Page 115 and 116:
QW-452 Performance Qualification Th
Page 117 and 118:
QW-430 F-NUMBERS QW-431 General The
Page 119 and 120:
Q32. Ferrous weld metal chemical co
Page 121 and 122:
Q36. What is the basic difference b
Page 123 and 124:
QW-304 Welders Except for the speci
Page 125 and 126:
Q40. Who is responsible for qualifi
Page 127 and 128:
Q44. A repair organization has a WP
Page 129 and 130:
QW-424 Base Metals Used for Procedu
Page 131 and 132:
Q45. What positions are necessary t
Page 133 and 134:
Q48. May a GMAW, short circuit tran
Page 135 and 136:
ESW Electroslag welding (ESW) is a
Page 137 and 138:
Charlie Chong/ Fion Zhang #11
Page 139 and 140:
Q54. A welder was qualified with a
Page 141 and 142:
Charlie Chong/ Fion Zhang
Page 143 and 144:
Q55. What are the primary classific
Page 145 and 146:
Q58. Applicable essential variables
Page 147 and 148:
Q62. The test that determines the u
Page 149 and 150:
Q66. A non-essential variable may b
Page 151 and 152:
Q71. Unless notch-toughness is a co
Page 153 and 154:
Q76. Variable QW 404.24 for SAW pro
Page 155 and 156:
Q81. A WPS must address all applica
Page 157 and 158:
Q86. A welder is qualified to weld
Page 159 and 160:
Q88. What period of inactivity from
Page 161 and 162:
Q92. Each manufacturer or contracto
Page 163 and 164:
Page 165 and 166:
QW-405.3 A change from upward to do
Page 167 and 168:
98. Under which of the following co
Page 169 and 170:
Page 171 and 172:
Happy Holi Charlie Chong/ Fion Zhan
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding API ICP653 Reading 15-Worksheet-11a

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?