Understanding API ICP653 Reading 15-Worksheet-11a

More documents

Recommendations

Info

Q7. The qualification of a new WPS or there-qualification of an existing WPS shall be in accordance with the: (a) component contract date. (b) current Edition and Addenda of Section IX. (c) 1962 or later Edition of Section IX. ANS: b Q8. In relation to the surface of the plate or pipe, what is the required test position orientation of a stud during welding? (a) Perpendicular to the surface. (b) ± <strong>15</strong> ° from the specified horizontal plane (c) ± <strong>15</strong> ° from the specified vertical plane. ANS: Charlie Chong/ Fion Zhang
Q9. How is the minimum specimen curvature of guided-bend jig specimens verified'? (a) A 1/8" diameter wire cannot be inserted between the specimen and the die. (b) A 1/8" diameter wire cannot be inserted between the specimen and the plunger. (c) The specimen is bottomed ejected. Q10. How is the tensile strength of a tension test specimen computed? (a) Dividing the maximum load by the least cross-sectional area of the specimen as measured before the load is applied. (b) Dividing the maximum load by the least cross-sectional area of the specimen as measured after the load is applied. (c) Measuring the percent of outer fiber elongation as required by the construction Code . ANS: b Charlie Chong/ Fion Zhang
Page 1 and 2: Charlie Chong/ Fion Zhang
Page 3 and 4: Expert at Works Charlie Chong/ Fion
Page 5 and 6: Expert at Works Charlie Chong/ Fion
Page 7 and 8: Charlie Chong/ Fion Zhang Fion Zhan
Page 9 and 10: The Magical Book of Tank Inspection
Page 11 and 12: API 653 Exam Administration -- Publ
Page 13 and 14: • API Recommended Practice 575, I
Page 15 and 16: Charlie Chong/ Fion Zhang
Page 17 and 18: ASME SECTION IX EXERCISES Charlie C
Page 19 and 20: TASK# 1 Read the following paragrap
Page 21: Q5. Where are notch-toughness requi
Page 25 and 26: Q13. Procedure and performance macr
Page 27 and 28: Charlie Chong/ Fion Zhang #2
Page 29 and 30: QW-191.1 Radiographic Examination Q
Page 31 and 32: Q3. When may longitudinal-bend test
Page 33 and 34: QW-100.3 Welding Procedure Specific
Page 35 and 36: Q8. What are the test orientations
Page 37 and 38: Task#2 Ref Para. 1. A QW-10()3 2. B
Page 39 and 40: Reading: General Requirements QW-10
Page 41 and 42: Q5. What constitutes a "set" of red
Page 43 and 44: Q7. The WPS must list ___ variables
Page 45 and 46: Task#3 Ref Para 1. A QW-484 2. C QW
Page 47 and 48: Reading: Procedure Qualifications Q
Page 49 and 50: Q5. The qualification of the ___is
Page 51 and 52: QW-200.4 (b) For GTAW, SMAW, GMAW,
Page 55 and 56: QW-200.4 Combination of Welding Pro
Page 57 and 58: Discussion: GTAW PQR variables: T=1
Page 59 and 60: Q5. What limitation is invoked when
Page 61 and 62: Q9: An organization's operational c
Page 63 and 64: Q12. The ____ is a true record of t
Page 67 and 68: Reading: Performance Qualifications
Page 69 and 70: Q5. How are the thickness limits de
Page 71 and 72: Q9. What welding positions on pipe
Page 73 and 74:
QW-304 Welders Except for the speci
Page 75 and 76:
TASK#7 Reading: Performance Qualifi
Page 77 and 78:
Q5. Why is the Manufacturer respons
Page 79 and 80:
Q9. When performance qualification
Page 81 and 82:
Q13. Failure of any portion of a co
Page 83 and 84:
Charlie Chong/ Fion Zhang #8
Page 85 and 86:
TASK#8 Welding Data QW-400 thru QW-
Page 87 and 88:
Q2. Under what conditions may a WPS
Page 89 and 90:
Q6. A change in a welding condition
Page 91 and 92:
Q8. The grouping of ____and____ by
Page 93 and 94:
Page 95 and 96:
TASK#9 Welding Data QW-451 thru QW-
Page 97 and 98:
Q3. In reviewing the form QW-483 (P
Page 99 and 100:
Q5. The SAW process is commonly cla
Page 101 and 102:
ASME SECTION IX PRACTICE QUESTIONS
Page 103 and 104:
Q5. New Welding Procedure Specifica
Page 105 and 106:
Q9. A welder qualifying with plate
Page 107 and 108:
Q12. Charpy V-notch tests are perfo
Page 109 and 110:
Q17. A WPS must describe: A. Essent
Page 111 and 112:
Q21. For the SAW process ______ is
Page 113 and 114:
Q26. Immediate retests of welders q
Page 115 and 116:
QW-452 Performance Qualification Th
Page 117 and 118:
QW-430 F-NUMBERS QW-431 General The
Page 119 and 120:
Q32. Ferrous weld metal chemical co
Page 121 and 122:
Q36. What is the basic difference b
Page 123 and 124:
QW-304 Welders Except for the speci
Page 125 and 126:
Q40. Who is responsible for qualifi
Page 127 and 128:
Q44. A repair organization has a WP
Page 129 and 130:
QW-424 Base Metals Used for Procedu
Page 131 and 132:
Q45. What positions are necessary t
Page 133 and 134:
Q48. May a GMAW, short circuit tran
Page 135 and 136:
ESW Electroslag welding (ESW) is a
Page 137 and 138:
Page 139 and 140:
Q54. A welder was qualified with a
Page 141 and 142:
Charlie Chong/ Fion Zhang
Page 143 and 144:
Q55. What are the primary classific
Page 145 and 146:
Q58. Applicable essential variables
Page 147 and 148:
Q62. The test that determines the u
Page 149 and 150:
Q66. A non-essential variable may b
Page 151 and 152:
Q71. Unless notch-toughness is a co
Page 153 and 154:
Q76. Variable QW 404.24 for SAW pro
Page 155 and 156:
Q81. A WPS must address all applica
Page 157 and 158:
Q86. A welder is qualified to weld
Page 159 and 160:
Q88. What period of inactivity from
Page 161 and 162:
Q92. Each manufacturer or contracto
Page 163 and 164:
Page 165 and 166:
QW-405.3 A change from upward to do
Page 167 and 168:
98. Under which of the following co
Page 169 and 170:
Page 171 and 172:
Happy Holi Charlie Chong/ Fion Zhan
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding API ICP653 Reading 15-Worksheet-11a

Create successful ePaper yourself

Delete template?

Save as template?