Understanding API ICP653 Reading 15-Worksheet-11a
Q3. The ——— is intended to provide direction for the welder, while the ——— was used in qualifying the ——— and details the test results. (a) WPS-PQR-WPQ (b) WPS-WPQ.-WPS (c) WPS-PQR-WPS, ANS: c Q4. What Figure Number is used for procedure qualification, reduced-section tension tests specimens, for pipe having an O.D. greater than 3"? (a) OW-462.1 (b) QW462.1 (c) QW462.1 ANS: Charlie Chong/ Fion Zhang
Q5. Where are notch-toughness requirements for the specimen, orientation and acceptance criteria found? (a) ASTM E208 (b) SA-370 (c) Construction Code ANS: b Q6. The radiographic acceptance criteria for welders qualified in accordance with QW-142 is found in: (a) The Construction Code (b) QW-191.2.2 (c) QW-192.2 ANS: Charlie Chong/ Fion Zhang
- Page 1 and 2: Charlie Chong/ Fion Zhang
- Page 3 and 4: Expert at Works Charlie Chong/ Fion
- Page 5 and 6: Expert at Works Charlie Chong/ Fion
- Page 7 and 8: Charlie Chong/ Fion Zhang Fion Zhan
- Page 9 and 10: The Magical Book of Tank Inspection
- Page 11 and 12: API 653 Exam Administration -- Publ
- Page 13 and 14: • API Recommended Practice 575, I
- Page 15 and 16: Charlie Chong/ Fion Zhang
- Page 17 and 18: ASME SECTION IX EXERCISES Charlie C
- Page 19: TASK# 1 Read the following paragrap
- Page 23 and 24: Q9. How is the minimum specimen cur
- Page 25 and 26: Q13. Procedure and performance macr
- Page 27 and 28: Charlie Chong/ Fion Zhang #2
- Page 29 and 30: QW-191.1 Radiographic Examination Q
- Page 31 and 32: Q3. When may longitudinal-bend test
- Page 33 and 34: QW-100.3 Welding Procedure Specific
- Page 35 and 36: Q8. What are the test orientations
- Page 37 and 38: Task#2 Ref Para. 1. A QW-10()3 2. B
- Page 39 and 40: Reading: General Requirements QW-10
- Page 41 and 42: Q5. What constitutes a "set" of red
- Page 43 and 44: Q7. The WPS must list ___ variables
- Page 45 and 46: Task#3 Ref Para 1. A QW-484 2. C QW
- Page 47 and 48: Reading: Procedure Qualifications Q
- Page 49 and 50: Q5. The qualification of the ___is
- Page 51 and 52: QW-200.4 (b) For GTAW, SMAW, GMAW,
- Page 53 and 54: Charlie Chong/ Fion Zhang #5
- Page 55 and 56: QW-200.4 Combination of Welding Pro
- Page 57 and 58: Discussion: GTAW PQR variables: T=1
- Page 59 and 60: Q5. What limitation is invoked when
- Page 61 and 62: Q9: An organization's operational c
- Page 63 and 64: Q12. The ____ is a true record of t
- Page 65 and 66: Charlie Chong/ Fion Zhang #6
- Page 67 and 68: Reading: Performance Qualifications
- Page 69 and 70: Q5. How are the thickness limits de
Q5. Where are notch-toughness requirements for the specimen, orientation<br />
and acceptance criteria found?<br />
(a) ASTM E208<br />
(b) SA-370<br />
(c) Construction Code<br />
ANS: b<br />
Q6. The radiographic acceptance criteria for welders qualified in accordance<br />
with QW-142 is found in:<br />
(a) The Construction Code<br />
(b) QW-191.2.2<br />
(c) QW-192.2<br />
ANS:<br />
Charlie Chong/ Fion Zhang