Understanding API ICP653 Reading 15-Worksheet-11a
Q84. A welder qualified to weld in the 2G position on pipe would have to be qualified in which of the addiiional positions to qualify for all position groove welding on pipe? A. 1G B. 2G C. 5G D. 6G E All of the above ANS: C Q85. The maximum preheat temperature decrease allowed without requalification of a GMAW groove weld procedure is: A. 50°F B. 100 o F C. 125 o F D. 150 o F E. None of the above ANS: b Charlie Chong/ Fion Zhang
Q86. A welder is qualified to weld all thicknesses of material when: A. The test is any thickness above 3/8 inch B. The test thickness was 1/2 inch C. The test thickness was 3/4 inch or over D. The test pipe wall thickness was 5/8 inch and nominal pipe size was over ½ inches E. None of the above ANS: b? 87. What is the maximum defect permitted on the convex surface of a welder qualification bend test after bending , except for corner cracks and corrosion resistant weld overlay? A. ¼ inch B. 1/8 inch C. 1/16 inch D. 3/16 inch E. No defects are allowed ANS: b Charlie Chong/ Fion Zhang
- Page 105 and 106: Q9. A welder qualifying with plate
- Page 107 and 108: Q12. Charpy V-notch tests are perfo
- Page 109 and 110: Q17. A WPS must describe: A. Essent
- Page 111 and 112: Q21. For the SAW process ______ is
- Page 113 and 114: Q26. Immediate retests of welders q
- Page 115 and 116: QW-452 Performance Qualification Th
- Page 117 and 118: QW-430 F-NUMBERS QW-431 General The
- Page 119 and 120: Q32. Ferrous weld metal chemical co
- Page 121 and 122: Q36. What is the basic difference b
- Page 123 and 124: QW-304 Welders Except for the speci
- Page 125 and 126: Q40. Who is responsible for qualifi
- Page 127 and 128: Q44. A repair organization has a WP
- Page 129 and 130: QW-424 Base Metals Used for Procedu
- Page 131 and 132: Q45. What positions are necessary t
- Page 133 and 134: Q48. May a GMAW, short circuit tran
- Page 135 and 136: ESW Electroslag welding (ESW) is a
- Page 137 and 138: Charlie Chong/ Fion Zhang #11
- Page 139 and 140: Q54. A welder was qualified with a
- Page 141 and 142: Charlie Chong/ Fion Zhang
- Page 143 and 144: Q55. What are the primary classific
- Page 145 and 146: Q58. Applicable essential variables
- Page 147 and 148: Q62. The test that determines the u
- Page 149 and 150: Q66. A non-essential variable may b
- Page 151 and 152: Q71. Unless notch-toughness is a co
- Page 153 and 154: Q76. Variable QW 404.24 for SAW pro
- Page 155: Q81. A WPS must address all applica
- Page 159 and 160: Q88. What period of inactivity from
- Page 161 and 162: Q92. Each manufacturer or contracto
- Page 163 and 164: Charlie Chong/ Fion Zhang
- Page 165 and 166: QW-405.3 A change from upward to do
- Page 167 and 168: 98. Under which of the following co
- Page 169 and 170: Charlie Chong/ Fion Zhang
- Page 171 and 172: Happy Holi Charlie Chong/ Fion Zhan
- Page 173 and 174: Happy Holi Charlie Chong/ Fion Zhan
- Page 175 and 176: Happy Holi Charlie Chong/ Fion Zhan
- Page 177 and 178: Charlie Chong/ Fion Zhang
- Page 179 and 180: Good Luck! Charlie Chong/ Fion Zhan
Q86. A welder is qualified to weld all thicknesses of material when:<br />
A. The test is any thickness above 3/8 inch<br />
B. The test thickness was 1/2 inch<br />
C. The test thickness was 3/4 inch or over<br />
D. The test pipe wall thickness was 5/8 inch and nominal pipe size was over<br />
½ inches<br />
E. None of the above<br />
ANS: b?<br />
87. What is the maximum defect permitted on the convex surface of a welder<br />
qualification bend test after bending , except for corner cracks and<br />
corrosion resistant weld overlay?<br />
A. ¼ inch<br />
B. 1/8 inch<br />
C. 1/16 inch<br />
D. 3/16 inch<br />
E. No defects are allowed<br />
ANS: b<br />
Charlie Chong/ Fion Zhang