Understanding API ICP653 Reading 15-Worksheet-11a
Q60. Name two defects that would cause visual rejection of a welder's test pipe or plate? A. Porosity, underfill B. Lack of penetration/ fusion C. Slag, overlap D. Any of the above ANS: d Q61. A variable that, when changed will cause a change in the mechanical properties of the weldment is called a: A. Essential variable B. Non-essential variable C. Supplementary essential variable D. All of the above ANS:a Charlie Chong/ Fion Zhang
Q62. The test that determines the ultimate strength of groove-weld joints is a: A. Notch Tough ness Test B. Tension Test C. Fillet Weld Test D. Guided-Bend Test ANS: b Q63. The procedure qualification test is used to determine: A. The skill of the welder B. That the proposed production weldment is capable of having the required properties C. The corrosion -resistance of the proposed weldment D. None of the above ANS: b Charlie Chong/ Fion Zhang
- Page 95 and 96: TASK#9 Welding Data QW-451 thru QW-
- Page 97 and 98: Q3. In reviewing the form QW-483 (P
- Page 99 and 100: Q5. The SAW process is commonly cla
- Page 101 and 102: ASME SECTION IX PRACTICE QUESTIONS
- Page 103 and 104: Q5. New Welding Procedure Specifica
- Page 105 and 106: Q9. A welder qualifying with plate
- Page 107 and 108: Q12. Charpy V-notch tests are perfo
- Page 109 and 110: Q17. A WPS must describe: A. Essent
- Page 111 and 112: Q21. For the SAW process ______ is
- Page 113 and 114: Q26. Immediate retests of welders q
- Page 115 and 116: QW-452 Performance Qualification Th
- Page 117 and 118: QW-430 F-NUMBERS QW-431 General The
- Page 119 and 120: Q32. Ferrous weld metal chemical co
- Page 121 and 122: Q36. What is the basic difference b
- Page 123 and 124: QW-304 Welders Except for the speci
- Page 125 and 126: Q40. Who is responsible for qualifi
- Page 127 and 128: Q44. A repair organization has a WP
- Page 129 and 130: QW-424 Base Metals Used for Procedu
- Page 131 and 132: Q45. What positions are necessary t
- Page 133 and 134: Q48. May a GMAW, short circuit tran
- Page 135 and 136: ESW Electroslag welding (ESW) is a
- Page 137 and 138: Charlie Chong/ Fion Zhang #11
- Page 139 and 140: Q54. A welder was qualified with a
- Page 141 and 142: Charlie Chong/ Fion Zhang
- Page 143 and 144: Q55. What are the primary classific
- Page 145: Q58. Applicable essential variables
- Page 149 and 150: Q66. A non-essential variable may b
- Page 151 and 152: Q71. Unless notch-toughness is a co
- Page 153 and 154: Q76. Variable QW 404.24 for SAW pro
- Page 155 and 156: Q81. A WPS must address all applica
- Page 157 and 158: Q86. A welder is qualified to weld
- Page 159 and 160: Q88. What period of inactivity from
- Page 161 and 162: Q92. Each manufacturer or contracto
- Page 163 and 164: Charlie Chong/ Fion Zhang
- Page 165 and 166: QW-405.3 A change from upward to do
- Page 167 and 168: 98. Under which of the following co
- Page 169 and 170: Charlie Chong/ Fion Zhang
- Page 171 and 172: Happy Holi Charlie Chong/ Fion Zhan
- Page 173 and 174: Happy Holi Charlie Chong/ Fion Zhan
- Page 175 and 176: Happy Holi Charlie Chong/ Fion Zhan
- Page 177 and 178: Charlie Chong/ Fion Zhang
- Page 179 and 180: Good Luck! Charlie Chong/ Fion Zhan
Q60. Name two defects that would cause visual rejection of a welder's test<br />
pipe or plate?<br />
A. Porosity, underfill<br />
B. Lack of penetration/ fusion<br />
C. Slag, overlap<br />
D. Any of the above<br />
ANS: d<br />
Q61. A variable that, when changed will cause a change in the mechanical<br />
properties of the weldment is called a:<br />
A. Essential variable<br />
B. Non-essential variable<br />
C. Supplementary essential variable<br />
D. All of the above<br />
ANS:a<br />
Charlie Chong/ Fion Zhang