STREETSCAPE GUIDANCE

Recommendations

Info

HOME INTRODUCTION PART A A vision for London’s streets PART B From strategy to delivery PART C New measures for new challenges PART D Balancing priorities PART F Appendix PART E Physical design and materials SECTION 6 Introduction SECTION 7 High quality footways SECTION 8 Carriageways SECTION 9 Crossings SECTION 10 Kerbside activity SECTION 11 Footway amenities SECTION 12 Safety and functionality SECTION 13 Street environment SECTION 14 Transport interchanges Streetscape Guidance [Part E – Physical design and materials] High quality footways 96 Figure 97: A selection of kerbs on the TLRN Standard TLRN kerb types The following guidance outlines the suite of standard kerb types used on the TLRN. This list focuses on the significance of the kerb upstand height and kerb profile for fulfilling a range of different functions in the street environment. It should be noted that for a typical kerb with an upstand of 125mm, the kerbstone will be approximately 300mm in total height as it will be bedded approximately 175mm below the carriageway surface. Dimensions stated are therefore not representative of the kerbstone size, but of the intended surface level aesthetic.
HOME INTRODUCTION PART A A vision for London’s streets PART B From strategy to delivery PART C New measures for new challenges PART D Balancing priorities PART F Appendix PART E Physical design and materials SECTION 6 Introduction SECTION 7 High quality footways SECTION 8 Carriageways SECTION 9 Crossings SECTION 10 Kerbside activity SECTION 11 Footway amenities SECTION 12 Safety and functionality SECTION 13 Street environment SECTION 14 Transport interchanges Streetscape Guidance [Part E – Physical design and materials] High quality footways 97 Kerb type Profile options Upstand height Application Standard straight kerbs Bull-nosed Maximum: 140mm (bus stops and central reserves) Standard: 125mm From footway to cycle tracks: 60-70mm maximum Low: 25mm (crossover) These kerbs can be laid on edge or flat. Standard sizes can be used on carriageway edges (30mph speeds or greater). Low sizes can be used in shared space settings, crossovers, or on-footway loading bay edge treatment as an option. 45° splayed Variable Used where vehicles may need to ride up on to the verge (ie in an emergency). Bespoke splayed transition kerbs are also used adjacent to designated cycle lanes to maximise the effective width of the lane (125mm upstand) although any other kerb with a maximum 60-70mm upstand fulfils the same purpose. Half-battered Variable Used to notify motorists when they are too close to the edge of the carriageway. Footpath can be provided next to this kerb. Edging Flush Flat topped edging laid on edge used to contain paving when transitioning from one material to another. Kerbs for channels Square edge Flush Can be laid on edge or laid flat based on requirements Channel (normally laid flat). These kerbs can be used to delineate a raised table at an entry treatment (normally laid on edge). Kerbs for corners Radius Maximum: 140mm Standard: 125mm To provide a smooth radius where the carriageway is turning. For corner radii greater than 15 metres, standard straight kerbs can be used interspersed with radius kerbs.
Page 1 and 2:
STREETSCAPE GUIDANCE Third Edition
Page 3 and 4:
HOME INTRODUCTION PART A A vision f
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
HOME Streetscape PART E Guidance Ph
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50: HOME INTRODUCTION PART A A vision f
Page 99: HOME INTRODUCTION PART A A vision f
Page 147 and 148: HOME PART E Physical design and mat
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
HOME PART E Physical design and mat
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335:
show all

STREETSCAPE GUIDANCE

Create successful ePaper yourself

Delete template?

Save as template?