Network UPS Tools User Manual

Recommendations

Info

Network UPS Tools User Manual 69 / 84 • http://pinoutsguide.com/UPS/best_power_pinout.shtml • http://lit.powerware.com/ll_download.asp?file=m_patriotproii_jan99.pdf • Stan Gammons G.6 Tripp-Lite From Tripp-Lite, via Bryan Kolodziej This cable (black 73-0844 cable) is used on various models, using the "Lan 2.2 interface" and the genericups driver (upstype=5). H Configure options There are a few options that can be given to configure to tweak compiles. See also "./configure --help" for a current and complete listing. H.1 Driver selection --with-serial Build and install the serial drivers (default: yes)
Network UPS Tools User Manual 70 / 84 --with-usb Build and install the USB drivers (default: auto-detect) Note that you need to install the libusb development package or files. --with-snmp Build and install the SNMP drivers (default: auto-detect) Note that you need to install libsnmp development package or files. --with-neon Build and install the XML drivers (default: auto-detect) Note that you need to install neon development package or files. --with-powerman Build and install Powerman PDU client driver (default: auto-detect) This allows to interact with the Powerman daemon, and the numerous Power Distribution Units (PDU) supported by the project. Note that you need to install powerman development package or files. --with-ipmi --with-freeipmi Build and install IPMI PSU driver (default: auto-detect) This allows to monitor numerous Power Supply Units (PSU) found on servers. Note that you need to install freeipmi (0.8.5 or higher) development package or files. --with-linux_i2c Build and install i2c drivers (default: auto-detect) Note that you need to install libi2c development package or files. --with-drivers=,,... Specify exactly which driver or drivers to build and install (this works for serial, usb, and snmp drivers, and overrides the preceding three options). As of the time of this writing (2010), there are 46 UPS drivers available. Most users will only need one, a few will need two or three, and very few people will need all of them. To save time during the compile and disk space later on, you can use this option to just build and install a subset of the drivers. To select mge-shut and usbhid-ups, you’d do this: --with-drivers=apcsmart,usbhid-ups If you need to build more drivers later on, you will need to rerun configure with a different list. To make it build all of the drivers from scratch again, run make clean before starting. H.2 Optional features --with-cgi (default: no) Build and install the optional CGI programs, HTML files, and sample CGI configuration files. This is not enabled by default, as they are only useful on web servers. See data/html/README for additional information on how to set up CGI programs. --with-doc= (default: no) Build and install NUT documentation file(s). The possible values are "html-single" for single page HTML, "html-chunked" for multi pages HTML, "pdf" for a PDF file or "auto" to build all the possible previous documentation formats. Verbose output can be enabled using: ASCIIDOC_VERBOSE=-v make This feature requires AsciiDoc 8.6.3 (http://www.methods.co.nz/asciidoc).
Page 1 and 2:
Network UPS Tools User Manual i Net
Page 3 and 4:
Network UPS Tools User Manual iii C
Page 5 and 6:
Network UPS Tools User Manual v Ins
Page 7 and 8:
Network UPS Tools User Manual vii 9
Page 9 and 10:
Network UPS Tools User Manual ix F
Page 11 and 12:
Network UPS Tools User Manual xi J.
Page 13 and 14:
Network UPS Tools User Manual 2 / 8
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Network UPS Tools User Manual 10 /
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30: Network UPS Tools User Manual 18 /
Page 79: Network UPS Tools User Manual 68 /
Page 95: Network UPS Tools User Manual 84 /
show all

Network UPS Tools User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?