Hohmann & Barnard catalog Reed First Source - Reed Construction ...

More documents

Recommendations

Info

Control Joints . Weep Holes . Mortar Net RS-Standard (2 5/8”) RS-Tee (2 5/8”) VS-Standard (2 5/8”) VS-Tee (2 5/8”) RS-8 (6 7/8”) VS-678 (6 7/8”) #341 Round Plastic Weep Holes #342 Rectangular Plastic Weep Holes #343 Louvered Weep Holes #343W Wilco TM Weep Holes QV Quadro-Vent TM The Mortar Net ® RS-12 (11 1/8”) VS-1118 (11 1/8”) RS Series - Rubber Control Joint Extruded rubber material designed for masonry walls at control joints. Rubber material conforms to ASTM D 2000 2AA-805. VS Series - PVC Control Joint The VS Series is a complete line of polyvinyl chloride control joints suitable for various wall conditions. PVC material conforms to ASTM D 2287 (Type PVC 654-4). Manufactured from post-industrial recycled material. #341 Series Standard - 1/4” or 3/8" outside diameter x 4" long. #342 Series Standard - 3/8" wide x 1-1/2" high x 3-1/2" long. #341W & #342W - Provided with cotton wick attached, for placement inside cavity. #341S & #342S - Provided with screen insert (Brass or Stainless Steel), to prevent infiltration of insects or debris. #341W/S & #342W/S - Provided with both wick and screen. #343 Standard - 2-1/4”, 2-7/8” or 3-1/2” high, injection-molded flexible PVC. Available only in Gray. Rectangular closer strip prevents mortar droppings from clogging openings. Compressible flanges for joint widths of 1/2” - 3/4”. #343W Standard - 2-1/4” or 3-3/4” high, painted aluminum. Available in Gray or White. Manufactured from post-industrial and/or post-consumer recycled material. Louvers direct passage of water from cavity to outside of building, while preventing reverse passage of water. Design permits air passage into cavity, thus aiding in pressure equalization while reducing suction. QV Standard: 3/8” x 3-3/8” x 2-1/2” high Jumbo: 3/8” x 3-3/8” x 3-1/2” high Other sizes available upon request. Colors: Gray, Clear, Cocoa, Tan or Almond Honeycomb design restricts ingress of insects and other debris. Allows passage of moisture up to its 2 1/2” height, important in the event of mortar droppings at bottom of cavity. Also suitable for top of wall venting. The Mortar Net ® - .4”, 1” or 2” thick x 10” high by 5’ long. Catches and permanently suspends mortar droppings in masonry cavity walls so water always has open flow paths to the weeps. The unique patented dovetail shape breaks up mortar droppings and prevents mortar damming. 2” thick is manufactured from recycled material. For material conformances, submittal sheets, CAD drawings and MSDS sheets see WWW.H-B.COM A19
Section A - Masonry Systems PTA Series Partition Top Anchors PTA Series Partition Top Anchors have been developed to provide lateral shear resistance at the upper limit of masonry walls. They permit vertical deflection of the slab above, without transferring compressive loads to the masonry wall below. PTA Series Anchors are suitable for construction using steel or concrete. PTA Tube with expansion filler is placed over rod anchor, which has been attached to concrete or steel by any of the methods illustrated. The vertical joint is then filled with mortar, fully surrounding tube. Other sizes available for heavy-duty applications. Contact H&B’s technical department. PTA-364 All details shown with H&B Neoprene Sponge PTA Tubes Clear butyrate tubes with compressible polyethylene filler (for use with all PTA series anchors except PTA-422) A20 PTA Series Partition Top Anchors Sizes: 12 ga. thick Finish: Mill Galv Hot Galv Stainless Steel PTA-420 PTA-422 (no PTA Tube required) Sizes: 12 ga. strap (5/16” dia. holes), 3/8” rod Finish: Mill Galv Hot Galv Stainless Steel Any H&B Gripstay Welded Bolted Welded Bolted H&B #305 H&B #305 Channel Connection Connection Connection Connection Dovetail Slot Dovetail Slot Typical Masonry Wall A B Sizes: 12 ga. thick available for 4”-12” block Finish: Mill Galv Hot Galv Stainless Steel PTA-RN Sizes: 3/8” threaded rod with beveled nut Finish: Mill Galv PTA-310 Sizes: 3/8” rod, 12 ga. dovetail head Finish: Mill Galv Hot Galv Stainless Steel Vertical Section Horizontal Section A B For material conformances, submittal sheets, CAD drawings and MSDS sheets see WWW.H-B.COM H& B recommends Type 304 Stainless Steel for maximum protection against corrosion.
Page 1 and 2: HB® Hohmann & Barnard, Inc. Design
Page 3 and 4: Section A - Masonry Systems TRUSS T
Page 5 and 6: Section A - Masonry Systems #180-BL
Page 7 and 8: Section A - Masonry Systems X-SEAL
Page 9 and 10: Section A - Masonry Systems MIGHTY-
Page 11 and 12: Section A - Masonry Systems New mas
Page 13 and 14: Section A - Masonry Systems A14 HB-
Page 15 and 16: Section A - Masonry Systems A16 Col
Page 17: Section A - Masonry Systems A18 Spy
Page 21 and 22: Section A - Masonry Systems Repair
Page 23 and 24: Section A - Masonry Systems H&B sou
Page 25 and 26: Flex-Flash ® Accessories Pre-Molde
Page 27 and 28: H&B Epra-MaxTM EPDM Thru-Wall Flash
Page 29 and 30: Available 1-1/2” or 3” wide (ot
Page 31 and 32: Section C - Residential C2 Wrap-N-S
Page 33 and 34: Section C - Residential Mite-Out TM
Page 35 and 36: Section C - Residential C6 Trac-Sea
Page 37: Hohmann & Barnard, Inc. www.h-b.com

Hohmann & Barnard catalog Reed First Source - Reed Construction ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?