DeltaV S-Series Traditional I/O

DeltaV Product Data Sheet 

October 2014 – Page 1 

S-Series Traditional I/O 

DeltaV S-Series Traditional I/O 

The DeltaV I/O interfaces are easy to install and maintain. 

• Modular and Flexible construction 

• Reduced installation time and expense 

• Easy Online expansion 

• Field mounted capable hardware 

• 1:1 Redundancy for Traditional I/O 

• Plug and Play IO 

Introduction 

S-series Traditional I/O interfaces provide improved ease 

of installation with the same proven features of M-series 

I/O interfaces. This modular I/O subsystem offers flexibility 

during installation and is designed for extreme 

environmental conditions of field installtions. S-series 

Traditional I/O is equipped with a snap in retention system 

for quick installation. The I/O interfaces can be installed in 

any of the possible 64 slots. 

All wiring is through the carriers and terminal blocks so 

that modules can easily be removed without disconnecting 

any wires. Modularity, fast installation, online expansion 

and environmentally robust hardware make DeltaV S- 

series Traditional I/O a smart choice for your process 

control system. 

www.DeltaV.com



Benefits 

Modular and Flexible construction. The S-series 

Traditional I/O subsystem is designed with your 

investment in mind. Each controller supports up to 8 I/O 

carriers that form a robust , passive bus for up to 64 I/O 

interfaces. Each interface has a matching I/O terminal 

block and can be installed in any I/O slot on the bus. 

Carriers and interfaces can be added online, without 

interruption to the existing I/O communication. This 

modular design enables you to purchase the exact amount 

of I/O cards, 8-wide carriers, power/controllers, and 2-wide 

carriers you need and add more DeltaV I/O as your 

system grows. 

Reduced installation time and expense. The 

DeltaV system’s S-series I/O interfaces are designed for 

quick assembly and error proof maintenance. All carriers 

snap onto T-DIN rails and interfaces snap into the I/O slots 

without the use of any tools. 

Each I/O interface has a separate wiring terminal block 

which connects field wiring to the interface. The I/O card 

can easily be removed without touching the I/O wiring on 

the terminal block. Some I/O cards can also use the fused 

terminal block, which is equipped with in-line fuses that 

can be pulled to isolate power to the field circuit. 

Traditional I/O interfaces have I/O function keys that allow 

the Terminal block to be set to receive a specific I/O card. 

These keys ensure that the correct I/O card is always 

plugged into the corresponding terminal block. The keys 

provide a safety measure by preventing the wrong I/O 

card’s being installed. It’s incredibly easy to use and gives 

you time to do more. 


Easy Online expansion. The S-series I/O carriers and 

interfaces can easily be added online, without disruption of 

exisinting I/O communication. I/O carriers can be extended 

online, either by directly connecting them to the right side 

of the existing carrier, or using extender cables to mount 

the new carrier on a different DIN rail. The controller 

automatically detects new carriers and interfaces and 

allows these to be auto-sensed into the configuration 

database. 

Field mounted capable hardware. All S-Series 

Traditional I/O interfaces are rated for extreme operating 

termperature ranges of -40 to 70 ºC (-40 to 158 ºF). The 

interfaces can be installed in field mounted enclosures so 

you significantly reduce the footprint of your equipment 

and increase valuable control room space for other uses. 

This also allows you to save on wiring expenses by 

eliminating the need for long runs of multi-cores. The 

integrated design of the I/O subsystem can eliminate the 

need for marshaling panels. This saves you even more in 

your total capital costs. 

1:1 Redundancy for Traditional I/O cards. 

Increased system availability is easy with S-series 

Traditional I/O cards. Four Traditional I/O card types are 

available with redundant terminal blocks for critical field 

circuits. Simply install a pair of cards on the prescribed 

redundant terminal block and DeltaV will automatically 

recognize them as a redundant pair. There is no 

configuration other than to autosense the redundant pair. 

All configuration options on the channels are consistent 

with the simplex version of the card. 

Plug-and-play I/O. All S-series Traditional I/O 

components plug into the I/O interface carrier and are auto 

sensed by the controller. There are no addressing 

switches or jumpers. Cards can be installed in any order 

simplifying the I/O subsystem design. New I/O interfaces 

are detected by the system and added to the engineering 

database automatically. Additional features can be 

enabled as needed and downloaded without disruption to 

existing I/O communication, allowing you to install the I/O 

you need today with the ability ot expand tomorrow. 

S-series terminal blocks. 

The I/O carriers provide integrated bussed field power 

distribution to the I/O interfaces. The integrated bus is 

divided into primary and secondary power for odd and 

even numbered slots. Each slot is individually fused to 

protect power to other cards. This significantly reduces the 

external power distribution circuits while still providing 

each card with fused 24 vdc bussed field power.



Product Description 

The S-series Traditional I/O subsystem 

includes: 

• I/O interface carrier ( DIN rail surface mounted) on 

which all I/O related components are installed. 

• Bulk AC to 24 VDC power supply for field devices. 

• A variety of analog and discrete I/O interfaces, 

consisting each of an I/O card enclosed in a common 

form factor and an associated I/O terminal block, 

which easily plug into the I/O interface carrier. 

• Cable Extenders that provide flexibility in carrier 

mounting. 


• AI (Plus) 4-20 mA HART, 16 channels 

• AO (Plus) 4-20 mA HART, 16 channels 

• DI (Plus) 24 VDC, Dry Contact, 32 channels 

• DO (Plus) 24 VDC, High-Side, 32 channels 

The following I/O cards are supported in simplex format to 

meet your field wiring needs. 

• AI Isolated, 4 channels 

• RTD, 8 channels 

• Thermocouple, 8 channels 

• Millivolt, 8 channels 

• DI 24 VDC Isolated, 8 channels 

• Pulse Count Input, 4 channels (Isolated DI) 

• Sequence of Event, 16 channels (DI 24 VDC) 

• DI 120 VAC Low Side Detection, 8 channels 

• DI 120 VAC Isolated , 8 channels 

• DO 24 VDC Isolated, 8 channels 

• DO 120/230 VAC High Side, 8 channels 

• DO 120/230 Isolated, 8 channels 

S-series traditional I/O Interface 

The I/O cards are connected to the field with a terminal 

block, which allows removal of I/O cards without 

disconnecting any field wiring. 

I/O Cards 

A variety of analog and discrete I/O interfaces are 

available to meet your specific requirements. The following 

cards support simplex or redundant installation: 

• AI 4-20 mA HART, 8 channels 

• AO 4-20 mA HART, 8 channels 

• DI NAMUR, 8 channels 

• DO 24 VDC High Side, 8 channels 

All I/O cards are enclosed in a common form factor that 

plugs into the I/O interface carrier. The housing is clearly 

labeled with the enclosed I/O card type. All cards have 

power and internal error indicators. Eight channel cards 

have clearly visible channel status LEDs. 

All cards meet ISA G3 corrosion specifications by the 

careful selection of superior electronic components and 

the use of conformal coating. 

Pulse Counters are available on most DI cards. The 

supported maximum frequency varies from 0.1 Hz on AC 

signals to 75 or 120 Hz on 24 VDC inputs, and up to 50 

KHz on the High Speed Pulse input card. 

DeltaV provides control module level time stamping for log 

events and alarms. For greater event resolution the 16 

channel Sequence of Event DI card can provide signal 

driven events to a resolution of +/- 0.25 ms per card, or 

within 1 ms per controller. Please refer to the Sequence of 

Events PDS for more in formation on Sequence of Event 

data collection and system options for this feature.



I/O Card Redundancy 

Redundant I/O cards are available for critical applications. 

The same card can be used in simplex or redundant 

applications. When installed on a two-wide redundant 

terminal block, the cards are recognized as a redundant 

pair by the controller. The controller scans each card and 

determines which card is acting as the active interface. 

When a fault is detected, the system automatically 

switches to the standby I/O card. 

DeltaV Control modules reference simplex and redundant 

I/O channels identically and there is no special 

configuration required to take advantage of redundancy. 

Switchover of a redundant I/O card is completed within 

two scans of the I/O bus. Make-before-break contacts 

ensure digital field instruments remain powered and the 

process is undisturbed. Analog output signals are briefly 

driven by both cards for < 5 ms during switchover of the 

card. 

Hardware Alerts automatically report hardware integrity 

errors for both the primary and secondary cards. Any 

event that causes a switchover is also reported 


automatically through the system hardware alerts and is 

logged in the Event Chronicle. Events that can cause a 

switchover include. 

• Hardware failure within the active card. 

• Communications failure between the active card and 

the controller. 

• Detection of a fault in the field wiring 

A switchover may also be initiated from the diagnostics 

explorer, and the health and status of both cards and their 

channels are available in the diagnostics explorer. 

The system automatically commissions a new standby 

card. In safe areas, failed cards can be replaced under 

power. In hazardous areas, appropriate installation 

procedures must be followed.




Hardware Specifications 

Common Environmental Specifications for all I/O Interfaces 

Operating temperature 

Storage temperature 

Relative humidity 

-40 to 70 C (-40 to 158 F) 

-40 to 85 C (-40 to 185 F) 

5 to 95% , non-condensing 

Protection rating IP 20, NEMA 12 

Airborne contaminants 

Shock 

Vibration 

ISA-S71.04-1985 Airborne Contaminants Class G3 

Conformal coating 

10 g ½-sine wave for 11 ms 

1 mm peak-to-peak from 5 to 13.2 Hz; 

0.7 g from 13.2 to 150 Hz 

S-series Traditional I/O interface enclosure




Analog Input signals 

Number of channels 8 

Specifications for AI Card, 8 channel, 4 to 20 mA, HART 

Input Sensor Types 

Full signal range 

Transmitter Power (2-wire) 

Accuracy over temperature range 

Repeatability 

Resolution 

Rolloff frequency (Anti-aliasing) 

Calibration 

LocalBus current per Card 

(12 VDC nominal) 

4 to 20 mA (span), 2-wire and 4-wire 

1 to 23 mA, with overrange checking 

13.5 V minimum at 20 mA (current limited at 29 mA max) 

0.1% of span 

0.05% of span 

16 bit A/D converter 

-3 dB at 2.7 Hz, -20.5 dB at 20 Hz 

None required 

Simplex: 120 mA typical, 150 mA maximum 

Redundant:175 mA typical, 250 mA maximum 

Field circuit power per card 300 mA maximum @ 24 VDC (+/-10%) 

Isolation 

Optional fuse 

HART Communications support 

Hart Scan Time 

Each channel is optically isolated from the system and 

factory tested to 1500 VDC. 

2.0 A (Terminal block option) 

HART pass-through for AMS Device Manager 

HART variable and status reporting for control functions 

600 – 800 mS (typical) per enabled channel 

Simplified circuit and connection diagram for simplex AI card, 8 channel, 4 to 20 mA, HART




Specifications for AI (Plus) Card, 16 Channel, 4 to 20 mA, HART 


Input Sensor Types 


Transmitter Power 


Repeatability 

Resolution 

Rolloff frequency (Anti-aliasing) 

Calibration 



4 to 20 mA (span), 2-wire 

2 to 22 mA, with overrange checking 

13.5 V minimum at 20 mA (max current limited at 29 mA) 

0.2% of span 

0.05% of span 


-3 dB at 2.7 Hz; -20.5 dB at 20 Hz 

None required 


Redundant: 110 mA typical, 200 mA maximum 

Field circuit power per Card 500 mA maximum @ 24 VDC (+/-10%) 

Isolation 



Each channel is optically isolated from the system and factory 

tested to 1500 VDC. 




Simplified circuit and connection diagram for simplex AI (Plus) card, 16 channel, 4 to 20 mA, HART




Specifications for RTD Input Card, 8 channel 

RTD channels per card 8 

Sensor types 

Resistance, Pt100, Pt200, Pt500, Ni120, Cu10, User Defined 

Sensor Configuration 

2 wire, 3 wire, or 4 wire 

Full Scale signal range 

See Table next page 

Accuracy 

See Table next page 

Repeatability 

0.05% of span 

Resolution 


Calibration 

None required 

Units 

Degrees C, Degrees F 

Sensor excitation current 100 µA 

Common mode rejection 

120 dB at 50/60 Hz 

LocalBus current (12 VDC nominal) 160 mA 

Open sensor detection 

Yes 

RTD, ohms Sensor Type Specifications 

Sensor Type Full Scale Operating Range 25° Reference 

Accuracy 

Temperature 

Drift 

Resolution 

Resistance 0 to 2,000 Ω 0 to 2,000 Ω ± 06.2 Ω ± 0.112 Ω/°C ~0.02 Ω 

Pt100 -200 to 850°C -200 to 850°C ± 0.5° C ± 0.018° C/°C ~0.05° C 

Pt200 -200 to 850°C -200 to 850°C ± 0.5° C ± 0.012° C/°C ~0.05° C 

Pt500 -200 to 850°C -200 to 850°C ± 3.5° C ± 0.063° C/°C ~0.18° C 

Ni120 -70 to 300°C 70 to 300°C ± 0.2° C ± 0.006° C/°C ~0.02° C 

Cu10 -30 to 140°C -30 to 140°C ± 2.0° C ± 0.157° C/°C ~0.23° C 

User Defined* 0 to 1000 Ω 0 to 1000 Ω ± 0.4 Ω ± 0.009 Ω/°C ~0.05 Ω 

* The Callendar-Van Dusen linearization equation can be used with user defined Pt RTDs. 

Refer to Recommended I/O Practices in DeltaV Books online for usage information.




Simplified circuit diagram for RTD Input card, 8 channels 

Specifications for Thermocouple/mV Input Card, 8 channel 

Channels per card 8 

Sensor types 

• Thermocouple 

• mV 

B, E, J, K, N, R, S, T, uncharacterized 

Low level voltage source 

Sensor Ranges 

Repeatability 

Resolution 

Calibration 

Units 

Cold junction compensation 

(Not available on mV channels) 

Isolation 

See table next page 

0.05% of span 


None required 

Degrees C 

Degrees F 

±1°C 



Channels 1, 2, 3, and 4 are isolated from channels 5, 

6, 7, and 8 (verified by 1500 VDC factory test). 

 

Thermocouples attached to channels 1, 2, 3, and 4 are 

not electrically isolated and should be within + 0.7 VDC 

of each other.




Specifications for Thermocouple/mV Input Card, 8 channel 

 

Thermocouples attached to channels 5, 6, 7, and 8 are 

not electrically isolated and should be within + 0.7 VDC 

of each other. 

Common mode rejection 

LocalBus current (12 VDC nominal) 

Open sensor detection 

120 dB at DC/50/60 Hz 

210 mA 

Yes 

Sensor Type Specifications 

Sensor Type Full Scale Operating Range 25° 

Reference 

Accuracy 

Temperature Drift Resolution 

B 250 to 1810° C 500 to 1810° C ± 2.4° C ± 0.056 ° C/ °C ~ 0.18° C 

E -200 to 1000° C -200 to 1000° C ± 0.6° C ± 0.008° C/ °C ~ 0.07° C 

J -210 to 1200° C -190 to 1200° C ± 0.8° C ± 0.011° C/ °C ~ 0.05° C 

K -270 to 1372° C -200 to 1372° C ± 0.5° C ± 0.016° C/ °C ~ 0.18° C 

N -270 to 1300° C -190 to 1300° C ± 1.0° C ± 0.007° C/ °C ~ 0.10° C 

R -50 to 1768° C -50 to 1768° C ± 2.1° C ± 0.013° C/ °C ~ 0.14° C 

S -50 to 1768° C -40 to 1768° C ± 2.2° C ± 0.067° C/ °C ~ 0.24° C 

T -270 to 400° C -200 to 400° C ± 0.7° C ± 0.001° C/ °C ~ 0.04° C 

mV Source/ 

Uncharacterized 

(no linearization or 

cold junction 

compensation.) 

-100 to 100 mV -100 to 100 mV 0.1 mV ± 0.002 mV/ °C ~ 0.003mV 

Simplified circuit diagram of Thermocouple/mV card, 8 channels





Specifications for Isolated Input Card,4 channel 

Sensor Types 

• Thermocouple 

• RTD Sensor Types 

• mV and V ranges 

B, E, J, K, N, R, S, T, Uncharacterized 

PT100, PT200, Ni120, Cu10, Resistance, User Defined 

Refer to following tables. 

Input type mix 

Resolution 

Calibration 

Isolation 

Common Mode Rejection 

Input Impedance 

Roll off frequency (Anti-aliasing) 

LocalBus Current (12 VDC nominal) 

Independently configurable 


None required 

Channel to system - 600 VAC double insulation. Each channel 

is optically isolated from the system and factory tested to 

5000 VDC. 

Channel to channel - 600 V basic insulation. Each channel is 

optically isolated from each other and factory tested to 3100 

VDC. 

CAN/CSA-C22.2 No.1010.1-92 

120 dB at DC/50/60 Hz 

10 MΩ 

-3dB at 2.7 Hz 

350 mA 

Isolated Input Card, Thermocouple and mV Input Specifications 

Linearization error 

Cold Junction Comp. Accuracy 

Cold junction compensation 

(Not available on mV channels) 

+/- 0.003% full scale 

+/- 1.0°C 

Local: Integrally mounted in terminal block 

External: Specified channel 

Cold Junction Compensation range -40 to 85°C 

Open circuit detection (Thermocouple 

only) 

Open sensor detection time 

Yes 

1 second




Isolated Input Thermocouple/mV/V Sensor Type Specifications 

Sensor Types Full Scale Operating Range 25°C Reference 

Accuracy 

Temperature 

Drift 

Nominal 

Resolution 

B 250 to 1810° C 500 to 1810° C ±1.2° C ±0.116 ° C/°C 0.09° C 

E -200 to 1000° C -200 to 1000° C ±0.5° C ±0.004° C/°C 0.05° C 

J -210 to 1200° C -190 to 1200° C ±0.6° C ±0.005° C/°C 0.06° C 

K -270 to 1372° C -140 to 1372° C ±0.5° C ±.013° C/°C 0.05° C 

N -270 to 1300° C -190 to 1300° C ±1.0° C ±.015° C/°C 0.05° C 

R -50 to 1768° C 0 to 1768° C ±1.7° C ±.083° C/°C 0.06° C 

S -50 to 1768° C 0 to 1768° C ±1.8° C ±.095° C/°C 0.08° C 

T -270 to 400° C -200 to 400° C ±0.7° C ±.025° C/°C 0.04° C 

Uncharacterized 

(no linearization 

or CJC) 

-100 to 100 mV -100 to 100 mV ±0.05 mV ±0.0003 mV/°C 0.0031 mV 

20 mV source -20 to 20 mV -20 to 20 mV ±0.02 mV ±0.001 mV/°C 0.0008 mV 

50 mV sourc -50 to 50 mV -50 to 50 mV ±0.03 mV ±0.0005 mV/°C 0.0017 mV 

100 mV source -100 to 100 mV -100 to 100 mV ±0.05 mV ±0.0003 mV/°C 0.0031 mV 

0 - 5 V 0 to 5 V 0 to 5 V ±0.005 V ±0.0002 V/°C 0.00009 V 

0 - 10 V 0 to 10 V 0 to 10 V ±0.010 V ±0.0004 V/°C 0.00016 V 

1 - 5 V 1 to 5 V 1 to 5 V ±0.0005 V ±0.0002 V/°C 0.00009 V 

1 V +/- 1 V +/- 1 V ±0.0025 V ±0.0002 V/°C 0.00015 V 

5 V +/- 5 V +/- 5 V ±0.005 V ±0.0002 V/°C 0.00017 V 

10 V +/- 10 V +/- 10 V ±0.010 V ±0.0004 V/°C 0.0003 V 

Simplified circuit diagram of Isolated Input card,Thermocouple, mV, V, 4 channels




Isolated Input Card, RTD, ohms Input Specifications 

Sensor configurations 

Excitation current 

Open sensor detection time 

Shorted sensor detection time 

2, 3, and 4 wire 

100 µA DC 

1 second 

1 second 

Pt 100 and Pt 200 alpha 0.00385 

Sensor Type 

Isolated Input Card, RTD, ohms Sensor Type Specifications 

Sensor Input Range 

25°C Reference 

Accuracy 

Temperature Drift 

Resolution 

Pt100 -200 to 850°C ± 0.5°C ± 0.018°C 0.05°C 

Pt200 -200 to 850°C ± 0.5°C ± 0.012°C 0.05°C 

Ni120 -70 to 300°C ± 0.2°C ± 0.006°C 0.02°C 

Cu10 -30 to 140°C ± 2.0°C ± 0.076°C 0.23°C 

Resistance 1 to 1000 ohm ± 0.5 ohms ± 0.018 ohms/°C 0.02 ohms 

User Defined* 0 to 1000 ohms ±0.4 ohms ±0.009 ohms/°C ~0.05 ohms 

* The Callendar-Van Dusen linearization equation can be used with user defined Pt RTDs. 

Refer to Recommended I/O Practices in DeltaV Books online for usage information. 

Simplified circuit diagram of Isolated Input card, RTD, 4 channels




Analog Output Signals 


Specifications for AO Card, 8 channel, 4 to 20 mA, HART 

Device Types 



Resolution 

Calibration 



4 to 20 mA 

1 to 23 mA 

0.25% of span (-40 to 60 ºC) 

0.4% of span (60 to 70 ºC) 

14 bit D/A converter 

None Required 



Field circuit power per card 300 mA maximum @ 24 VDC (+/-10%) 

Isolation 

Output compliance voltage 

Open-Loop Detection 

Optional fuse 




tested to 1500 VDC 

20 mA at 21.6 VDC supply into 700 load 

< 0.70 mA 





Simplified circuit and connection diagram for simplex AO card, 8 channel, 4 to 20 mA, HART




Specifications for AO (Plus) Card, 16 Channel, 4 to 20 mA, HART 


Device Types 



Resolution 

Calibration 



4 to 20 mA 

1 to 23 mA 

0.25% of span 


None required 



Field circuit power per Card 400 mA maximum @ 24 VDC (+/-10%) 

Isolation 








Simplified circuit and connection diagram for simplex AO (Plus) card, 16 channel, 4 to 20 mA, HART




DC Voltage Discrete Input Cards 


Specifications for DI Card, 8 channel, 24 VDC, NAMUR 

Input Compatibility 

Detection level for On 

Detection level for Off 


Wetting Voltage 

Fault Detecction capable 

Configurable channel types: 

• Discrete input 

• Pulse Count 

Compatible with NAMUR Sensors 

2.2 mA 

1 mA 

5 K (approximate) 

15 Volts 

NAMUR Sensors or field resistor pack 

Input 

Dry contact or discrete state sensor changing





Specifications for DI Card, 8 channel, 24 VDC, Isolated 



Input impedance 

Wetting Current 


• Discrete input 

• Pulse Count 

10 VDC 

5 VDC 

5K Ω (approximately) 

6 mA at 24 VDC 

Input signal profile 

Dry contact or discrete state sensor changing




Specifications for DI (Plus) Card, 32 channel, 24 VDC, Dry Contact 




Termination Fault Detection 

(A Mass Terminal Block feature only) 




2 mA 

0.25 mA 

Only available on Plus Cards when used with the S-Series Mass 

Connection Solutions or P+F HiD or HiC barriers and boards 

5K ohm (approximate) 

24 VDC 

50 mA typical, 75 mA maximum 

Field circuit power per card 150 mA maximum @ 24 VDC (+20%/-15%) 

Isolation 

Each channel is optically isolated from the system 

and factory tested to 1500 VDC. 

Simplified circuit and connection diagram for DI Card, 32 channel, 24 VDC, Dry contact 

Simplified circuit and connection diagram for simplex DI Plus Card, 32 channel, 24 VDC, Dry contact




Specifications for PCI Card, 4 channel, 24 VDC, Dry Contact 


Detection level for ON (min.) 

Detection level for OFF (max.) 


>4.8 VDC (>5 mA) 




Specifications for SOE Card, 16 channel, 24 VDC, Dry Contact 






Channel Scan Rate 

Time Stamp Accuracy (for SOE enabled 

channels only) 1 


Field circuit power per card 

Isolation 

2 mA 

0.25 mA 

5K ohm (approximate) 

24 VDC 

0.25 msec for all 16 channels 

0.25 msec from same card 

1 msec from same controller 


75 mA at 24 VDC 



Simplified circuit and connection diagram for SOE card, 16 channel, 24 VDC, Dry contact 

1 

Refer to Sequence of Event Product Data Sheet for more information on System capabilities and Sequence of Event data collection.




DC Voltage Discrete Output Cards 

Specifications for DO Card, 8 channel, 24 VDC, High Side 


Output range 24 VDC +/- 10% 

Output rating 

Off state leakage 


• Discrete output 

• Momentary output 

• Continuous pulse output 

1.0 A maximum continuous per channel; 

3.0 A maximum per I/O Interface. 

(Inrush 4.0A for < 100mSec, 6.0A for < 20 mSec) 

1.2 mA maximum 

Output signal profile 

Output stays in last state submitted by the control logic. 

Output remains active for a pre-configured time period. 

Output is active as a percentage of a pre-configured base time 

period (100 ms to 100 s). Resolution = 5 ms 



Isolation 

Optional fuse 


3.0 A at 24 VDC per I/O Interface 

(internal 10-Amp fast acting non-ressettable fuse) 


tested to 1500VDC. 

2.0 A 

Simplified circuit and connection diagram for DO card, 8 channel, 24 VDC, High Side





Specifications for DO Card, 8 channel, 24 VDC, Isolated 

Output range 

Output rating 






2 VDC to 60 VDC 

1.0 A (inrush 4.0 A for < 100 ms; 6A for < 20 ms) 









Isolation 


None 

Each channel is optically isolated from the system and from 

each other and factory tested to 1500 VDC. 

Simplified circuit and connection diagram for DO card, 8 channel, 24 VDC, Isolated




Specifications for DO (plus) Card, 32 channel, 24 VDC, High-Side 


Output rating 

100 mA per channel 

Output range 24 VDC 10% 

Off-state leakage 

Termination Fault Detection 

(A Mass Terminal Block feature only) 



Only available on Plus Cards when used with the S-Series Mass 

Connection Solutions or P+F HiD or HiC barriers and boards 


Field circuit power per card 3.2 A @ 24 VDC (+20%/-15%) 

Isolation 



Simplified circuit and connection diagram for simplex DO (Plus) Card, 32 channel, 24 VDC, High- Side




AC Voltage Discrete Input Cards 

Specifications for DI Card, 8 channel, 120 VAC, Dry Contact 



1.4 mA 


0.56 mA 


2 mA at 120 VAC 

Output Impedance 

60 K (approximately) 

LocalBus current (12 VDC nominal) 75 mA typical, 100 mA maximum 



Isolation 

Each channel is optically isolated from the system at 250 VAC 

Optional fuse 

2.0 A 

Simplified circuit and connection diagram for DI card, 8 channel, 120 VAC, Dry Contact









LocalBus current (12 VDC Nominal) 


Isolation 

Optional fuse 

Specifications for DI Card, 8 channel, 120 VAC, Isolated 

84 to 130 VAC 

0 to 34 VAC 


60 K (approximately) 


None 


and from other channels at 250 VAC. 


Simplified circuit and connection diagram for DI card, 8 channel, 120 VAC, Isolated




AC Voltage Discrete Output Cards 

Specifications for DO Card, 8 channel, 120/230 VAC, High Side 2 


Output range 

Output rating 






20 to 250 VAC 

375mA average per channel 

1.0 A maximum continuous per channel 

(inrush 5 A for < 100 ms; 20 A for < 20 ms) 

3.0 A maximum per card 

2 mA maximum at 120 VAC 









Isolation 

Optional fuse 


3.0 A at 120 VAC or 230 VAC 


2.0 A (inrush 5A for < 10 ms at 0.1% duty cycle) 

Simplified circuit and connection diagram for DO card, 8 channel, 120/230 VAC, HighSide 

2 

High-side means the output signal is switched on the positive leg. Switching on the positive leg avoids current in field wiring 

when there is no output signal.




Specifications for DO Card, 8 channel, 120/230 VAC, Isolated 



Output range 

Output rating 







20 to 250 VAC 

375mA average per channel 

1.0A maximum continuous per channel; 

(inrush 5A for < 100 ms: 20A for < 20 ms) 

3.0A maximum per card 








Isolation 

Optional fuse 


None 

Each channel is optically isolated from system at 250 VAC and 

from other channels at 250 VAC 

2.0 A (inrush 5A for < 10 ms at 0.1% duty cycle) 

Simplified circuit and connection diagram for DO card, 8 channel, 120/230 VAC, Isolated



I/O Terminal Blocks 

A variety of I/O terminal blocks is available to meet 

specific functionality and environmental requirements of 

the installation. The I/O interface is a combination of the 

I/O card and the I/O terminal block. Each I/O interface is 

uniquely keyed so that once installed in a carrier slot with 

a terminal block, that terminal block will only accept like 

replacement card. 


The keys prevent installation of an incorrect card, and the 

graphical information on the card makes it easy to 

determine if a keyed slot will accept a particular card. 

There are 9 different simplex I/O terminal blocks available 

to meet the wiring needs of field signals. 

• 8 Channel Terminal Block 

• Fused 8 Channel Terminal Block 

• AI 8 Channel Terminal Block 

• AI 16 Channel Terminal Block 

• AO 16 Channel Terminal Block 

• Discrete 32 Channel Terminal Block 

• Isolated Input Terminal Block 

• RTD/Resistance Terminal Block 

• Thermocouple Terminal Block 

The following redundant I/O terminal blocks are available 

on some I/O interfaces, allowing a pair of cards to be 

installed as a redundant pair. 

• Redundant AI 8 Channel Terminal Block 

• Redundant AO 8 Channel Terminal Block 

8 channel standard Terminal block 

The keying mechanism consists of two keying posts that 

rotate and lock into the terminal block base. Each post 

has 6 positions: A-F and 1-6. Each card is assigned a 

unique key which is marked on the side of the I/O card: 

• Redundant Discrete 8 Channel Terminal Block 

The table on the following page lists the compatible 

terminal blocks for each card, along with the cards unique 

key positions. The first terminal block listed is the 

recommended terminal block. 

In addition to standard signal wiring, some cards may also 

be ordered with Mass Terminal blocks that allow these 

cards to be connected to the S-Series Mass 

Connection Solutions or third party wiring solutions from 

Phoenix or if IS Barriers are required from Pepperl and 

Fuchs, mounted in an adjacent cabinet in order to meet 

special signal conditioning or for optimizing field wiring 

solutions. Please refer to the Alliance Program website for 

details on approved 3 rd parth products. 

• 16-pin Mass Terminal Block (simplex only) 

• 24-pin Mass Terminal Block (simplex only) 

Keying position for HART AI, 4-20 mA, 8 channel 

• 40-pin Mass Terminal Block (simplex and redundant) 

• 48-pin Mass Terminal Block (simplex and redundant)




Low Voltage Traditional I/O and terminal block compatibility: 

I/O Card 

I/O Card 

Keying 

Traditional I/O Terminal Blocks 

Mass Terminal Blocks 

AI, 8-channel, 4–20 mA, 

HART 

A1 

AI 8-Channel Terminal Block 

- (Supports 2 and 4 wire devices) 

16-pin Mass Terminal Block 

(Supports 2-wire Devices) 

Redundant AI 8-channel Terminal Block 

Fused 8-Channel Terminal Block 


(Supports 4-wire Devices) 

8-Channel Terminal Block 

AI, 16-channel, 4-20 mA 

HART 

AI Plus, 16-channel, 

4-20 mA HART 

A2 AI 16-Channel Terminal Block NA 

A6 NA 48-pin AI Mass Terminal Block 

Redundant 48-pin Mass AI Term. Block 

(Supports 2 and 4-wire Devices) 

AO, 8-channel,4–20 mA, 

HART 

A4 


Redundant AO 8-Channel Terminal Block 



AO Plus, 16-channel, 

4-20 mA HART 

A5 AO 16-Channel Terminal Block 48-pin AO Mass Terminal Block 

Thermocouple, mV C1 Thermocouple Terminal Block 


RTD, 8-channel C3 RTD/Resistance Terminal Block NA 

Isolated Input Card C2 Isolated Input Terminal Block NA 

Redundant 48-pin Mass AO Term. Block 

NA 

DI, 8-channel, 24 VDC, 

NAMUR 

B1 


Redundant Discrete 8-Channel Terminal 

Block 



DI, 8-channel, 24 VDC, 

Isolated 

B2 




DI, 32-channel, 24 VDC 

Dry contact 

DI Plus, 32-channel, 24 VDC 

Dry contact 

B3 Discrete 32-Channel Terminal Block 40-pin Mass Terminal Block 

E3 NA Redundant 40-pin Mass DI Term. Block 

(Supports Termination Fault Detection) 

PCI, 4-channel C6 Discrete 32-Channel Terminal Block NA 

SOE, 16-channel,24 VDC C5 Discrete 32-Channel Terminal Block 40-pin Mass Terminal Block 

DO, 8-channel, 24 VDC, 

High-Side 

B6 


Redundant Discrete 8-Ch. Terminal Block 



DO, 8-channel, 24 VDC, 

isolated 

B5 




DO, 32-channel, 24 VDC 

High-Side 

DO Plus, 32-channel, 24 

VDC High-Side 

B4 Discrete 32-Channel Terminal Block 40-pin Mass Terminal Block 

B4 NA Redundant 40-pin Mass DO Term. Block 

(Supports Termination Fault Detection)




High Voltage Traditional I/O and terminal block compatibility: 

I/O Card 

I/O Card 

Keying 

Traditional I/O Terminal Blocks 

Mass Terminal Blocks 

DI, 8-channel, 120 VAC, 

Dry contact 

E1 



NA 

DI, 8-channel, 120 VAC, 

isolated 

E4 



NA 

DO, 8-channel, 120 VAC/ 

230 VAC, high side 

F1 



NA 

DO, 8-channel, 120 VAC/ 

230 VAC, isolated 

F4 



NA




System Compatibility 

S-series Traditional I/O hardware requires: 

• SQ, or SX controllers 

• S-series horizontal carriers 

S-series and M-series controllers can be installed on the 

same DeltaV Area Control Network in v11.3.1 and beyond. 

Control modules can be assigned to any controller and 

inter-controller references are fully supported. 

DeltaV SIS Safety Logic Solvers can be installed under an 

S-series controller using SIS horizontal and verticalplus 

carriers. Refer to PDS_SLS_1508_LogicSolver and 

PDS_S-series_Horizontal_Carriers and as well to the 

PDS_S-series_VerticalPlus Carriers product data sheets 

for more information. 

The following Traditional I/O Plus cards require V13.3 or 

higher Software: 

- AI Plus, 4-20 mA HART, 16 channels 

- AO Plus, 4-20 mA HART, 16 channels 

- DI Plus, 32-channel, 24 VDC Dry contact 

- DO Plus, 32-channel, 24 VDC High-Side 

Termination Fault Detection is a feature wich only works 

within the following cards: 

- DI Plus, 32-channel, 24 VDC Dry contact 

- DO Plus, 32-channel, 24 VDC High-Side 

when used with the redundant 40-pin Mass DI or DO 

Terminal Block combined with the S-Series Mass 

Connection Solutions or P+F HiD or HiC IS barriers and 

termination boards for DeltaV. 

All other approved 3rd party mass termination products 

may be used with both non Plus S-series and M-series I/O 

interfaces. 

S-series Traditional I/O does not install on vertical 

carriers.For vertical I/O applications, use Electronic 

marshalling with CHARMS I/O. 

S-series Traditional I/O horizontal carriers are not 

physically compatible with M-series horizontal controller 

carriers. Install S-series I/O interfaces with S-series 

controllers and M-series I/O interfaces with M-series 

controllers.




Certifications 

The following certifications are available for S-series Traditional I/O: 

• CE: 

- EMC- EN 61326-3-1:2006 

- LVD: Directive 2006/95/EC Aug 2007 

• FM: 

- FM 3600, Dec. 2011 

- FM 3611, Dec. 2004 

- FM 3810, Jan 2005 

- ANSI/ISA 60079-0, Oct 2009 

- ANSI/ISA 60079-15, Jul 2009 

• CSA: 

- CSA C22.2 No. 213-M1987, 1987 

(Reaffirmed 2008) 

- CSA C22.2 No. 61010-1, 2004 


CAN/CSA-E60079-0, 2007 

- CAN/CSA-E60079-15, March 2002 


• ATEX: 

- ATEX 94/9/EC 

- EN60079-0: 2009 

- EN60079-15:2005 

- EN60079-15:2010 

• IEC-Ex: 

- IEC60079-0:2007 

- IEC60079-15:2005 

- IEC60079-15:2010 

• Marine Certifications: 

IACS E10:2006 Rev.5 Control, Protection & 

Safety; DNV 2.4:2006 

- ABS Certificate of Design Assessment 

- Bureau Veritas Certificate 

- DNV Marine Certificate 

- Lloyds Register 

• GOST Hazardous Area certification Zone 2 

(Russian) 

- POCC US.ГБ05.B03564



Certifications 

S-series Traditional I/O Cards will be submitted for the following certifications: 


• EAC Hazardous Area certification Zone 2 

(Russian, Belarus, Kazakhstan)



Hazardous Area/Location: 

S-series Traditional I/O Cards can be installed and used based on the following Standards: 

• FM (USA): 

Installation and Field Circuits: 

Class I, Division 2, Groups A, B, C, D, T4 

• cFM (Canada): 


Class I, Division 2, Groups A, B, C, D, T4 

• ATEX: 


• IEC-Ex: 

Ex nA IIC T4 Gc 

Ex nA [nL] IIC T4 Gc 

Ex nA [ic] IIC T4 Gc 

Ex nA nC IIC T4 Gc 


Ex nA IIC T4 Gc 

Ex nA nL IIC T4 Gc 

Ex nA ic IIC T4 Gc 

Ex nA nC IIC T4 Gc 


Regarding the Installation instructions please refer to the following Documents: 

Class 1 Division 2 Installation Instructions DeltaV S-Series 

Zone 2 Installation Instructions DeltaV S-Series 

12P5402 Rev. C 

12P5404 Rev. C




Additional Field Circuit Certification Information 

DC Voltage Traditional I/O Card Description 

Class I 

Zone 2 

Zone 2 

Zone 2 

Division II 

Ex nL 

Ex ic 

Ex nA 

Non Incendive 

Certified 

Certified 

Certified 

AI, 8 Channels 4-20 mA, HART 

AI, 16 Channels 4-20 mA, HART 

AI Plus, 16 Channels 4-20 mA, HART ─ 

RTD/Resistance, 8 Channels ─ 

TC/mV, 8 Channels 

TC/mV/V/RTD Isolated, 4 Channels ─ 

AO, 8 Channels 4-20 mA, HART ─ 

AO Plus, 16 Channels 4-20 mA, HART ─ ─ 

DI, 8 Channels, 24VDC, NAMUR ─ 

DI, 8 Channels, 24VDC, Isolated ─ ─ ─ 

DI, 32 Channels, 24 VDC, Dry Contact ─ ─ ─ 

DI Plus, 32 Channels, 24 VDC, Dry Contact ─ ─ ─ 

PCI, 4 Channels, 24 VDC Dry Contact ─ ─ ─ 

SOE, 16 Channels, 24 VDC, Dry Contact ─ ─ ─ 

DO, 8 Channels 24VDC, High-Side ─ ─ ─ 

DO, 8 Channels 24VDC, Isolated ─ ─ ─ 

DO, 32 Channels, 24VDC, High-Side ─ ─ ─ 

DO Plus, 32 Channels, 24VDC, High-Side ─ ─ ─ 

AC Voltage Traditional I/O Card Description 

Class I 

Division II 

Zone 2 

Ex nL 

Zone 2 

Ex ic 

Zone 2 

Ex nA 

Non Incendive 

Certified 

Certified 

Certified 

DI, 8 Channels, 120VAC, Isolated ─ ─ ─ ─ 

DI, 8 Channels, 120VAC, Dry Contact ─ ─ ─ ─ 

DO, 8 Channels 120/230VAC, Isolated ─ ─ ─ ─ 

DO, 8 Channels 120/230VAC, High-Side ─ ─ ─ ─



Ordering Information 


Description 

Analog Input, 8 Channels 4-20 mA, HART 

Analog Input Cards and Terminal Blocks 

AI Card: 8 Channels 4-20 mA, HART, AI 8-Channel Terminal Block 

AI Card: 8 Channels 4-20 mA, HART, Fused 8-channel Terminal Block 

AI Card: 8 Channels 4-20 mA, HART, 16-Pin Mass I/O Terminal Block 

AI Card: 8 Channels 4-20 mA, HART, 24-Pin Mass I/O Terminal Block 

Redundant Analog Input, 8 Channels 4-20 mA, HART 

Model Number 

SE4003S2B1 

SE4003S2B2 

SE4003S2B4 

SE4003S2B5 

2 x AI Card, 8 Ch, 4-20 mA, HART, AI 8 Channel redundant Terminal Block SE4033S2B1 

Analog Input 16 Channels 4-20 mA, HART 

Analog Input Card: 16 Channels 4-20 mA, HART, AI 16-Channel Terminal Block 

Analog Input Plus Card: 16 Channels 4-20 mA, HART, 48 Pin AI Mass Terminal Block 

(to be used with P+F HiD or HiC IS barriers and termination boards for DeltaV) 

Analog Input Plus Card: 16 Channels 4-20 mA, HART, 48 Pin AI Mass Terminal Block 

including 16 Channel AI MASS CONNECTION BOARD * supporting 2-& 4-wire Devices 

Redundant Analog Input 16 Channels 4-20 mA, HART 

2 x AI Plus Card: 16 Channels 4-20 mA, HART, Red. 48 Pin AI Mass Terminal Block 


2 x AI Plus Card: 16 Channels 4-20 mA, HART, Red. 48 Pin AI Mass Terminal Block 

including 16 Channel AI MASS CONNECTION BOARD * supporting 2-& 4-wire Devices 

RTD/Resistance, 8 Channels 

RTD Card: 8 Channels, RTD/ Resistance Terminal Block 

Thermocouple/mV, 8 Channels 

mV Card: 8 Channels; 8-ChanneL Terminal Block 

Thermocouple Card: 8 Channels; Thermocouple Terminal Block 

Isolated Input, 4 Channels (Thermocouple/mV/V, RTD) 

Isolated Input Card, 4 Channels; Isolated Input terminal Block 

SE4003S2B6 

SE4003S2B11 

SE4053S2B11 

SE4033S2B11 

SE4083S2B11 

SE4003S6B1 

SE4003S4B1 

SE4003S5B1 

SE4003S7B1 

* 

For more Details on the DI Mass Connection Board and Connection cables, please refere to the PDS S-series 

Mass Connection Solution




Analog Output Cards and Terminal Blocks 

Description 

Model Number 

Analog Output, 8 Channels 4-20 mA, HART 

AO Card: 8 Channels 4-20 mA, HART, 8-Channel Terminal Block 

AO Card: 8 Channels 4-20 mA, HART, Fused 8-Channel Terminal Block 

AO Card: 8 Channels 4-20 mA, HART, 16-Pin Mass Terminal Block 

SE4005S2B1 

SE4005S2B2 

SE4005S2B3 

Redundant Analog Output, 8 Channels 4-20 mA, HART 

2 x AO Card, 8 Ch, 4-20 mA, HART, Redundant AO 8-Channel Terminal Block SE4035S2B1 

Analog Output 16 Channels 4-20 mA, HART 

Analog Output Plus Card: 16 Channels 4-20 mA, HART, AO 16-ChannelTerminal Block SE4005S2B4 

Analog Output Plus Card: 16 Channels 4-20 mA, HART, 48 Pin AO Mass Terminal 

Block 


Analog Output Plus Card: 16 Channels 4-20 mA, HART, 48 Pin AO Mass Terminal 

Block 

including 16 Channel AO MASS CONNECTION BOARD * 

SE4005S2B5 

SE4055S2B5 

Redundant Analog Output 16 Channels 4-20 mA, HART 

2 x AO Plus Card: 16 Channels 4-20 mA, HART, Red. 48 Pin AO Mass Terminal Block 


2 x AO Plus Card: 16 Channels 4-20 mA, HART, Red. 48 Pin AO Mass Terminal Block 

including 16 Channel AO MASS CONNECTION BOARD * 

SE4035S2B5 

SE4085S2B5 

* For more Details on the DI Mass Connection Board and Connection cables, please refere to the PDS S-series 





VDC Discrete Input Cards and Terminal Blocks 

Description 

Model Number 

Discrete Input Card: 8 Channels, 24Vdc, NAMUR 

DI Card: 8 Channels, 24Vdc, Dry Contact, 8-Channel Terminal Block 

DICard: 8 Channels, 24Vdc, Dry Contact, Fused 8-Channel Terminal Block 

DI Card: 8 Channels, 24Vdc, Dry Contact, 16-Pin Mass Terminal Block 

SE4001S2T2B1 

SE4001S2T2B2 

SE4001S2T2B3 

Redundant Discrete Input, 8 Channels, 24Vdc, NAMUR 

2 x DI Card, 8 Ch, NAMUR, Redundant Discrete 8-Channel Terminal Block SE4031S2T2B1 

Discrete Input Card: 8 Channels, 24Vdc, Isolated 

DI Card: 8 Channels, 24Vdc, Isolated, 8-Channel Terminal Block 

DI Card: 8 Channels, 24Vdc, Isolated, Fused 8-Channel Terminal Block 

DI Card: 8 Channels, 24Vdc, Isolated, 16-Pin Mass Terminal Block 

SE4001S2T1B1 

SE4001S2T1B2 

SE4001S2T1B3 

Discrete Input Card: 32 Channels, 24 Vdc, Dry Contact 

DI Card: 32 Channels, 24 Vdc, Dry Contact, Discrete 32-Channel Terminal Block 

DI Card: 32 Channels, 24 Vdc, Dry Contact, 40-pin Mass Terminal Block 


DI Card: 32 Channels, 24 Vdc, Dry Contact, 40-pin Mass Terminal Block 

including 2 x 16 Channel DI MASS CONNECTION BOARDs * 

SE4001S2T2B4 

SE4001S2T2B5 

SE4051S2T2B5 

Redundant Discrete Input Card: 32 Channels, 24 Vdc, Dry Contact 

2 x DI Plus Card: 32 Channels, 24 Vdc, Dry Contact, Red. 40-pin DI Mass Terminal Block SE4031S2T2B7 


2 x DI Plus Card: 32 Channels, 24 Vdc, Dry Contact, Red. 40-pin DI Mass Terminal Block SE4081S2T2B7 

including 2 x 16 Channel DI MASS CONNECTION BOARDs * 

Pulse Count Input Card: 4-Channels, 24 Vdc, Dry Conatact 

PCI Card: 4 Channels, 24 VDC Dry Contact; Discrete 32 Channel Terminal Block 

SE4015 

Sequence of Event Input Card: 16 Channels, 24 Vdc Dry Contact 

SOE Card: 16 Channels, 24 Vdc, Dry Contact; Discrete 32-Channel Terminal Block 

SOE Card: 16 Channels, 24 Vdc, Dry Contact; 40-pin Mass Terminal Block 

SE4001S5T2B4 

SE4001S5T2B5 






VDC Discrete Output Cards and Terminal Blocks 

Description 

Model Number 

Discrete Output Card: 8 Channels 24Vdc, High Side 

DO Card: 8 Channels 24Vdc, High Side, 8-Channel Terminal Block 

DO Card: 8 Channels 24Vdc, High Side, Fused 8-Channel Terminal Block 

DO Card: 8 Channels 24Vdc, High Side, 16-Pin Mass Terminal Block 

SE4002S1T2B1 

SE4002S1T2B2 

SE4002S1T2B3 

Redundant Discrete Output, 8 Channels, 24Vdc, High Side 

2 x DO Card, 8 Ch, High Side, Redundant Discrete 8-Channel Terminal Block SE4032S1T2B1 

Discrete Output Card: 8 Channels 24Vdc, Isolated 

DO Card: 8 Channels 24Vdc, Isolated, 8-Channel Terminal Block 

DO Card: 8 Channels 24Vdc, Isolated, Fused 8-Channel Terminal Block 

DO Card: 8 Channels 24Vdc, Isolated, 16-Pin Mass Terminal Block 

SE4002S1T1B1 

SE4002S1T1B2 

SE4002S1T1B3 

Discrete Output Card, 32 Channels, 24Vdc, High Side 

DO Card, 32 Channels, 24Vdc, High Side, Discrete 32-Channel Terminal Block 

DO Card, 32 Channels, 24Vdc, High Side, 40-Pin Mass I/O Terminal Block 


DO Card: 32 Channels, 24 Vdc, High Side, 40-Pin Mass I/O Terminal Block 

including 4 x 8 Channel DO MASS CONNECTION BOARDs * 

SE4002S1T2B5 

SE4002S1T2B6 

SE4052S1T2B6 

Redundant Discrete Output Card, 32 Channels, 24Vdc, High Side 

2 x DO Plus Card, 32 Channels, 24Vdc, High Side, 40-Pin DO Mass I/O Terminal 

Block 


2 x DO Plus Card: 32 Channels, 24 Vdc, High Side, 40-Pin DO Mass I/O Terminal Block 

including 4 x 8 Channel DO MASS CONNECTION BOARDs * 

SE4032S1T2B8 

SE4082S1T2B8 






VAC Discrete Input Cards and Terminal Blocks 

Description 

Model Number 

Discrete Input Card: 8 Channels, 120Vac, Isolated 

DI Card: 8 Channels, 120Vac, Isolated, 8-Channel Terminal Block 

(1 Power Terminal Plug incl. for dedicated Power supply through the 8-Wide I/O 

Carrier) 

DI Card: 8 Channels, 120Vac, Isolated, Fused 8-Channel Terminal Block 


Carrier) 

SE4001S3T1B1 

SE4001S3T1B2 

Discrete Input Card: 8 Channels, 120Vac, Dry Contact 

DI Card: 8 Channels, 120Vac, Dry Contact, 8-Channel Terminal Block 

(1 Power Terminal Plug incl. for dedicated Power supply through the 8-Wide I/O Carrier) 

DI Card: 8 Channels, 120Vac, Dry Contact, Fused 8-Channel Terminal Block 


SE4001S3T2B1 

SE4001S3T2B2 

VAC Discrete Output Cards and Terminal Blocks 

Description 

Model Number 

Discrete Output Card: 8 Channels 120/230Vac, Isolated 

DO Card: 8 Channels 120/230Vac, Isolated, 8-Channel Terminal Block 


Carrier) 

DO Card: 8 Channels 120/230Vac, Isolated, Fused 8-Channel Terminal Block 


Carrier) 

SE4002S2T1B1 

SE4002S2T1B2 

Discrete Output Card: 8 Channels 120/230Vac, High Side 

DO Card: 8 Channels 120/230Vac, High Side, 8-Channel Terminal Block 


DO Card: 8 Channels 120/230Vac, High Side, Fused 8-Channel Terminal Block 

SE4002S2T2B1 

SE4002S2T2B2




Description 

VAC Discrete Output Cards and Terminal Blocks 


Model Number




Spare part ordering Information 

Description 

250V 2A Fuse for Fused Terminal Block; Box of 20 

Spare Parts 

Model Number 

KJ4010X1-BC1 

. 

To locate a sales office near you, visit our website at: 

www.EmersonProcess.com/DeltaV 

Or call us at: 

Asia Pacific: 65.6777.8211 

Europe, Middle East: 41.41.768.6111 

North America, Latin America: 

+1 800.833.8314 or 

+1 512.832.3774 

For large power, water, and wastewater applications 

contact Power and Water Solutions at: 

www.EmersonProcess-powerwater.com 

Or call us at: 

Asia Pacific: 65.6777.8211 

Europe, Middle East, Africa: 48.22.630.2443 

North America, Latin America: +1 412.963.4000 

© Emerson Process Management 2013. All rights reserved. For Emerson Process Management trademarks and service marks, go to: 

http://www.emersonprocess.com/home/news/resources/marks.pdf. 

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be 

construed as warrantees or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed 

by our terms and conditions, which are available on request. We reserve the right to modify or improve the design or specification of such products at any time 

without notice. 

www.DeltaV.com

DeltaV S-Series Traditional I/O

Create successful ePaper yourself

Delete template?

Save as template?