TUAREG 92 4x4 EVO APACHE 92 4x4 EVO - Oleo-Mac
TUAREG 92 4x4 EVO APACHE 92 4x4 EVO - Oleo-Mac
TUAREG 92 4x4 EVO APACHE 92 4x4 EVO - Oleo-Mac
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Malfunction, defect<br />
Remedy<br />
Check that the blades are not bent or twisted, also check that they are balanced. If they are<br />
deformed, replace them.<br />
Check that the belt does not have burned areas or irregularities, which could cause the vibrations.<br />
If the belt is damaged, replace it.<br />
Belts vibrate<br />
extremely when<br />
turning on the<br />
mowing deck<br />
The travel drive<br />
belt of the machine<br />
is slipping<br />
The travel drive<br />
belt is being<br />
excessively worn<br />
out<br />
The machine does<br />
not travel after<br />
shifting into gear<br />
The machine is<br />
unusually loud<br />
after shifting into<br />
gear<br />
The machine<br />
loses power when<br />
travelling up a hill<br />
Extreme vibrations<br />
occur when<br />
travelling<br />
The steering is<br />
slipping through or<br />
loose<br />
Check that the blades are not worn out or damaged. Replace them if necessary.<br />
Check that the electromagnetic clutch switches properly. If the clutch is not working properly<br />
have it replaced or repaired at an authorised service centre.<br />
Check the inside surface of the pulley on the engine. If it is coarse or has cracks, it is necessary to<br />
replace the pulley.<br />
Check whether grass has accumulated on the underside of the mowing deck. It is necessary to<br />
remove this grass.<br />
Check whether the defect is not in the engine mount. Tighten bolts or replace as necessary.<br />
Check the tension of the belt ( 6.3.7. If necessary adjust the tension.<br />
Check the tension of the travel drive belt ( 6.3.8). If necessary adjust its tension. Also check<br />
the tension spring, replace it if necessary.<br />
Check whether the belt is damaged or worn out.<br />
Check whether the movement of the clutch mechanism is blocked by a foreign object. If yes,<br />
remove the foreign object.<br />
Check the engine pulley or transmission pulley for damage. Replace if necessary.<br />
Check belt tension.<br />
Check the tensioning mechanism, replace the damaged spring<br />
Check whether a foreign object is blocking the movement of the belt. If yes, remove the foreign<br />
object.<br />
Check the condition of the pulleys - replace the pulleys if necessary.<br />
Check the gear shifting mechanism - attachment of the draw bar of the travel direction lever.<br />
Check the oil level in the equalisation tank<br />
Check the oil level in the equalisation tank and fill it up if necessary.<br />
There are air pockets in the hydraulic circuit – drive the machine on level ground forward and<br />
back for several minutes. Contact your service centre.<br />
When the machine is under a high load and the ambient temperature is high, then the maximum<br />
working temperature of the oil may be exceeded. Lower the work demands on the machine.<br />
Check whether any pulleys are damage or deformed. Replace them if necessary.<br />
Check whether the belt has any burned spaces or other irregularities. Replace it if necessary.<br />
Check the tension of the travel drive belt ( 6.3.8). If necessary adjust its tension.<br />
Check that the mowing blades are balanced. Balance or replace them if necessary.<br />
Check that the space between the pinion and the segment is not too large. If yes, adjust the<br />
cogged segment. Check for wear on the ball and socket joints. Replace the joints if necessary.<br />
Check that there is petrol in the petrol tank.<br />
Check that the prescribed procedure for starting the engine was followed ( 5.2)<br />
Check the fuse. Replace if necessary.<br />
The engine does<br />
not run<br />
Check whether the voltage on the battery terminals is 12 V. On a new machine check whether the<br />
battery was activated and charged. On new machines replace the spark plug and check that there<br />
is not oil accumulated on the cylinder due to incorrect handling.<br />
Check that all wire connections are in order and that the electrical system switches work.<br />
Check the engine again exactly according to the instructions in the User’s manual of the engine<br />
manufacturer. Have the electrical system checked at a specialised workshop.<br />
42